INSTALLATION GUIDE FOR CRIMP CONNECTORS

Slides:



Advertisements
Similar presentations
Filter Changing Procedures For TEOM Series 1400ab and Model 8500 FDMS (B & C Types)
Advertisements

About ICM ICM Corporation is the global manufacturer of our patented 360° radial compression technology in both connectors and tools. Our F-Conn connectors.
Corning Cabelcon 1. 2 To begin with – we need some tools… Cable cutter Cabelcon Rotary Stripper Mounting tool Compression tool Please read the instructions.
CRIMPING Introduction
How to install a PL-259 My Way! by Steve, N1NXU. Start with a clean cut. Notice how the top cable end is a nice clean round cut. It was cut with a cable.
Zebra® Z4000, Z4M™, Z4Mplus™ Removing and Installing Printhead
Cap Sewing with HCS-1201 Voyager
Department of Environmental Conservation 1 DATAMAX PRINTER SETUP MODULE 1.
Purpose Body Making module is designed for bending the laminated foil film in the shape of a tube, for welding the side seam and for cutting bodies with.
Installation Procedures
Installation instructions for the one and only 3 point strut bar for the 5 th gen Accord Please follow the instructions to ensure proper fitment of the.
ModICE Modular Integrated Connector Enclosure
Copyright 2008 Kenneth M. Chipps Ph.D. How to Terminate a Corning Unicam Connector Last Update
Connector Installation Guide For Compression and Mechanical Connectors
1 Zebra 170 XiIII Plus Removing and Installing Printhead Calibrating Head Resistance Print Quality Adjustments.
Corning Cabelcon 1. 2 To begin with – we need some tools… Cable cutter Cabelcon RG11 Rotary Stripper Mounting tools Compression tool Please read the instructions.
Mini Reel Hand Tools. JST Mini Reel Hand Tool JST is proud to introduce the JST Mini Reel hand tool and explain the features, benefits and basic operation.
Welcome to Autoescorts Please Press F5 to view & Press Enter to change Slides.
Heating foil ECOFILM F Installation guide. ECOFILM F - OPTION Suitable for laminate floating floors: width(mm) input (W/m 2 ) F F (48V) 530.
Adding to your Diagnostic Station Adding to your Diagnostic Station.
Connect To Success Selection & Proper Installation of Coax Connectors.
The UTE Speed-O-Calibration Unit (SOC) is used to calibrate the locomotive speedometer. This presentation is an operations outline for Ultra-Tech model.
CONNECTORS, CABLES & SOLUTIONS Presentation I-Net M12 Crimp Field Industrial Ethernet D-Code 360° EMI/RFI Shielding with crimp flange system Railway cable.
Wiring MVRT 2010 – 2011 Season. Table of Contents Wire stripping Crimping Soldering.
Bob Howard 10/22/2011.  How many connectors do you need ◦ Max DC/Servo Motor Controllers is 4 so use 4  How long should the connectors be ◦
1 Fiber Optics LIGHT CRIMP TERMINATIONS USING THE PRENTIUM KIT.
5-15. Connect To Success Selection & Proper Installation of Coax Connectors.
OBJECTIVES 1. Create correctly sized connectivity cabling.
Usage Guidelines Throughout this template you will find tip-boxes to the left of the slides. To remove this box from the final presentation, simply click.
After Receiving this error code, Follow these steps to correct the problem… Click for next slide.
Copyright 2008 Kenneth M. Chipps Ph.D. How to Use the 3M Mechanical Splice Tool Last Update
Health and Safety. The Health and Safety at Work Act 1974 An Act to make further provision for securing the health, safety and welfare of persons at work,
CONNECTORS, CABLES & SOLUTIONS Presentation I-Net M12 Crimp Field Industrial Ethernet D-Code 360° EMI/RFI Shielding with crimp flange system 8/2010.
PROFIBUS wiring/installation can be done with:
Lighting and Wiring Services
5.1.? Student Book © 2005 Propane Education & Research CouncilPage 1 Selecting the pump for a propane dispenser should include a complete understanding.
The Mavica for the Maverick: A How-to Guide Operating instructions for the Sony Mavica CD350 Digital Camera An Easy-to-Follow Guide to Everything You Need.
Control System and Electrical Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team
lesson 3.3 STARTING, STOPPING, STEERING, AND TARGETING
PARKING BRAKE OPERATION, DIAGNOSIS, AND SERVICE
Framed Canopy Fitting Instructions Contents – 6- Angled frame fixing brackets 1 x handle pack 6 x self drilling tech screws 3 keys 1x door 6 x coach screws.
Flex Cam – Training This shows one version of a complete FlexCam system including Power Unit HCP and Compact Cam CC for piercing operation.
Project On Ethernet Cable Building & Video Recording James Maclean & Stephen Craig.
WeldFit Push-in Fittings
Grapple Housing Top Sub Grapple Collet Seal Housing Bottom Sub Seal Housing Metal Seal Ring.
Adding to your Diagnostic Station Adding thermometry The temperature module attaches to the top of the BP module. It is made up of the following two.
SAMI MAKERSPACE MAKE: AN ELECTRONICS WORKSHOP. TOOL BASICS.
IOPtiMate™ OT-135P2 Technical Training – Part I System Description, Installation & Operation IOP (07)
Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.
Hardware Configuration Guide Configuring Dongles and Creating Barcodes for Devices Used with VSC.
Getting Started with your Diagnostic Station Getting Started with your Diagnostic Station.
UTP cabeling. Introduction This document shows how to properly construct a Crossover network cable. This cable can be used to directly connect two computers.
YJQ-W1Q Pneumatic Crimping Tool Instruction GENERAL INFORMATION 1. YJQ-W1Q is widely used for the crimping of wires and contacts in electronic connectors.
UTH-65A VER. CAUTIONS ! PLEASE USE THE OUTLET PREPARED BY A QUALIFIED SERVICEMAN AND MUST CONFIRM IT BEFORE APPLY[SING AN ELECTRIC CURRENT.
THE CENTRE LATHE - 'FACING OFF' A very basic operation is called ‘facing off’. A piece of steel has been placed in the chuck and the lathe cutting tool.
VIEW SERIES with Sliding Door
Select your System Freedom Micro DI.
What is TETRIX? If you can dream up a robot design, you can build it with the TETRIX Robotics Design System.
Scorpion is a remote tester specifically designed for testing ASD systems. Scorpion is compatible with the FAAST aspirating smoke detector. It is particularly.
CAUTION GENERAL TOOLS REQUIRED ASSEMBLY AND INSTALLATION
2-Blades Model The V-block can be reversed, and the indication arrow"}" shows recommended cable size (RG). Stripping distance can be changed if user moves.
INSTALLATION GUIDE FOR CRIMP CONNECTORS
ASSEMBLY/INSTALLATION INSTRUCTIONS ASSEMBLY AND INSTALLATION
Meeting In A Box Set Up Guide
CAUTION GENERAL TOOLS REQUIRED ASSEMBLY AND INSTALLATION
Coax Connector 3 Piece Connector Assembly Gerry Crenshaw WD4BIS www
Installation guide for RG6/59 compression connectors
Wire Stripping and Crimping
Installation guide for CX3 RG 7/11 compression connectors
Presentation transcript:

INSTALLATION GUIDE FOR CRIMP CONNECTORS How to prepare your cable? How to install your crimp connectors? You can step forward and back in this guide using your arrow buttons...

The quality of your work can be seen by your customers... Follow this guide to ensure a good result of your installation!

First of all... Please always make sure to use the right size of connector for your cable. Poor installation or using the wrong type of connector for your cable will decrease the electrical, mechanical and environ- mental performance of your system. Cabelcon manufactures various sizes of connectors, also to match your cable. Examples of Cabelcon crimp connectors

Use a proper cable stripper... The use of Cabelcon’s Rotary Cable Strippers are recommended. They are all designed for precise stripping dimensions to match Cabelcon’s crimp connectors. This is important for correct connectorisation! Cabelcon’s Rotary Cable Strippers also save time on installation. Please read the instructions supplied with the tool. Rotary Stripper for RG6/59

- and the right hex size of your crimping tool It is also important to crimp your connector with the right hex size (MINI - ALM - UNIV - RG11). Always crimp in one operation. Avoid to re-crimp with a smaller tool size or with another tool - not intended for crimping.

Now, we are ready to work... Strip your cable. Stripping dimensions (A & B) must be as follows: A = 6.5 mm (4mm for EPA short) B = 6.5 mm at IEC 169-24 (Europe) B = 8.0 mm at SCTE SP 401-199X (US) (a “B” dimension of 6.5 mm will be sufficient in most cases) Cabelcon’s Rotary Strippers are designed and pre-adjusted to make these dimensions in one operation. A B

Next... Fold exposed braid back over the jacket. This is how to do it: For Quad shield, Tri shield and Super Shield cables: Remove the outer braid and foil only. Fold back the inner braid. Leave inner foil attached to dielectric. Make sure that the foil is undamaged and smooth. This is how to do it: Use your arrow buttons to go forward and back

Then... Most of Cabelcon’s F-crimp connectors for RG 6/59 have a built-in “tool” (chamfer) in the front part to ensure a smooth foil before installation - when needed. (Note: This is normally not necessary after using Cabelcon’s Rotary Cable Stripper). Before After Press the front part of the connector against the cable (when needed) and turn slowly to prepare the foil to enter into the connector .

Mount the connector... Push the connector over the foil and allow the support mandrel to slide between the foil and the braid. Press and turn until the dielectric is flush with the support mandrel face. A mounting tool can be used to keep a better grip on the connector during installation.

Now we are ready to crimp... Open the crimp tool and place the connector in the hex opening. Crimp over the area (between the red lines) as shown. Slowly crimp the connector until the lever arm is closed.

That’s all... - and it’s that easy. Please always read the operation instructions supplied with the tools. Mounting instructions for your specific type of connectors can be supplied from Cabelcon on request.

Finally - a selection of our tools for crimp connectors Rotary Cable Strippers Item no. 98501010 for ALM, UNIV, EPA (RG6/59) Item no. 98501011 for new EPA (short body) Item no. 98501102 for RG11 Item no. 98501000 for DT596 (RG6/59) ALM, UNIV, EPA (RG6/59) DT596 (RG6/59) RG11 More tools..

- more tools for crimp connectors... Cabelcon recommend the use of Torque Wrench Spanners when installing F-connectors. This is to ensure a proper installation in accordance to SCTE standards and thus to minimise the risk of heavy screening leakage. SCTE recommends a torque of 3,4 - 5,6 Nm for F-connectors. (More types can be supplied). Torque Wrench TW407 Item no. 98029090 Mounting tool - Item no. 98028620 Cable Cutter - Item no. 98028620

and last - but not least ... Cabelcon’s crimping tools. Type For use to A B Item no. CRP 106C ALM - MINI .262 - .324 98028820 CRP 106H ALM - UNIV .324 - .360 98028840 CRP 106F ALM - RG11 .324 - .475 98028830 CRP 106J UNIV - RG11 .360 - .475 98028850

A Cabelcon guide to installation of crimp connectors December 1999 Copyright ©1999 by Cabel-Con A/S, Denmark