Carpentry and Joinery Year 11 Mr O’Neill

Slides:

Advertisements

Similar presentations

OH & S WHOSE RESPONSIBILITY IS IT ???. The Victorian Occupational Health & Safety Act (2004) states that the employer must as far as is reasonably practicable,

Advertisements

S2 Course Choice Craft, Design & Technology V1.1 25/1/07.

Unit 1005 Maintain and use carpentry and joinery hand tools © Pearson Education 2010 Printing and photocopying permitted Learning Outcome 1 Know how to.

Vocational (craft) routes: Construction Level 1 Electrical Installations Plumbing & Heating Brickwork Carpentry and Joinery Painting and Decorating 3 GCSEs.

Digital Electronics Soldering & De-soldering. 2 This presentation will… Review the tools needed to solder and de-solder electronic components. Demonstrate.

ERGONOMIC SOLUTIONS ERGONOMIC SOLUTIONS Designing The Workplace To Best Protect The Health And Safety Of Employees.

ERGONOMIC SOLUTIONS Designing The Workplace To Best Protect The Health And Safety Of Employees.

Key Stage 3 A Bird Feeder A Suggested Year 9 / 10 Project RA Moffatt WELB.

Vocational (technical) routes: Construction Level 1 Electrical Installations Plumbing & Heating Brickwork Carpentry and Joinery Painting and Decorating.

WELCOME TO PRODUCT DESIGN With Mr Yule and Mr Zierer.

1 Personal Protective Equipment Module 6. 2Objectives After this module you should be able to – identify the most common PPE-related hazards – take the.

Safety when cutting with knives. By Fergus Evans..

Welding, Subpart J OSHA 500 Course. Critical Hazards n Heat is a source of ignition in the various welding processes n Welding fumes can become a health.

Unit 204: Common plumbing processes

Material Safety Data Sheets & Contamination MSDS MSDS is an acronym for Material Safety Data Sheets and is used as a resource for chemical management.

Environment & Sustainability

Tools, Fire Extinguishers and Explosives Section E of the Forest Activities Code.

Engineering & Technology General Safety Rules

Front Slide Jo Richardson Community School.

Instructor: Mr. Ruffino Wood Lab Technologies. COURSE DESCRIPTION: This course is designed to concentrate on all basic wood construction methods. Students.

Health And Safety At Work Act (HSWA) is… A piece of Legislation enforced by the local authorities along with the Health and Safety Executive that covers.

Soldering. Soldering Tools Soldering Iron Soldering Iron Care & Maintenance Tinning Process Good Solder Connections Bad Solder Connections De-Solder Process:

Unit 1006 Maintain and use carpentry and joinery power tools © Pearson Education 2010 Printing and photocopying permitted Learning Outcome 1 Know how to.

Unit 1006 Maintain and use carpentry and joinery power tools © Pearson Education 2010 Printing and photocopying permitted Learning Outcome 2 Know how to.

Year 9 KS4 Course Choices Parents Information Evening 2010 Route B – 25 th January.

Table of Contents Unit 1- Understand the Problem Unit 2- Gather Information Unit 3- Develop Solutions Unit 4- Implement A Solution Unit 5- Test and Evaluate.

Product Design Specification - PDS The Product Design Specification (PDS) is a very important document in the design process as it contains all the information.

MANUFACTURING. Storage of materials, mostly different types of woods.

1 Part 2 Directions: As your instructor goes through the safety rules for the lab, write down the missing word or words in the blank spaces on your student.

Craft Skills What is Craft Skills? In Curriculum for Excellence Craft Skills is the subject that used to be known as PRACTICAL CRAFT SKILLS.

Proposed Agriculture Courses Board of Education October 6, 2015.

Cabinetmaking 1 Mr. Higgins. ► Review ► Descriptions ► Outlines ► Course Competency ► Expectations ► Materials.

Unit 1005 Maintain and use carpentry and joinery hand tools © Pearson Education 2010 Printing and photocopying permitted Learning Outcome 2 Know how to.

Small Engine Safety Jesse Morris Spring 2002 Virginia Tech This presentation has not been edited by the Georgia Curriculum Office.

New Revised Specification In Construction For 1st teaching September 2009 For moderation 2011.

ENGINEERING CRAFT SKILLS Bench Skills - Metal Machine Processes - Metal Fabrication & Thermal Joining + Coursework Project.

BTEC CONSTRUCTION 2014 BTEC Course Mrs C. Bollans Head of Technology Mr C Wright Assistant Head of Technology.

Year 10 GCSE Focus Evening. Work Experience Mr T Beal Work Experience Mr T Beal GCSE Focus Evening.

Level 1 Diploma in Electrical Installation © 2014 City and Guilds of London Institute. All rights reserved. 1 of 7 PowerPoint presentation Supporting information.

LO.2.2 MB1 How can you simplify an experienced maintenance procedure in order to produce a maintenance plan that is more efficient and easier to follow?

SILS4 OFFSITE LEARNING for FOUNDATION LEARNING 2009/10 Terry O’ReganTerry O’Regan.

Session 2: Cutting and Shaping Tools; Other Common Hand Tools

Hand Tool Safety Use the right SIZE and TYPE of tool for the job

Soldering Magic of Electrons © 2011 Project Lead The Way, Inc.

WJEC Construction at Monkwearmouth

Careers in Manufacturing

Simplifying Fractions

Year 9 Subject Selection – VET Building and ConstructionTaster

Auto Upkeep Basic Car Care, Maintenance, and Repair (2nd Edition)

Lab Safety Procedures Mrs. Mondry’s Class.

Craft Occupations in the Construction Industry

Manufacturing Production of goods primarily by the application of labor and capital to raw materials.

Design & Technology Department Port Glasgow High School

Tools and equipment needed for this task..

Technology Department Desborough College

LADDER SAFETY TRAINING

Soldering & De-soldering

Auto Upkeep Basic Car Care, Maintenance, and Repair (2nd Edition)

Hand Tool Safety Use the right SIZE and TYPE of tool for the job

Auto Upkeep Basic Car Care, Maintenance, and Repair (2nd Edition)

Soldering & Desoldering

WORKSHOP SAFETY BOOKLET….

CRAFT KNIFE SAFETY WSR ART DEPT..

Hand and Power Tool Safety

Tank Project… Name: _______________________________.

ERGONOMIC SOLUTIONS Designing The Workplace To Best Protect The Health And Safety Of Employees.

Soldering & De-soldering

Personal Details Name:Mr.Klaus Ndumba Student number: Institution:NUST Course:HCVET Learning area: Joinery and Carpentry

Presentation transcript:

Carpentry and Joinery Year 11 Mr O’Neill Occupational studies Carpentry and Joinery Year 11 Mr O’Neill

Occupational studies 2 year course Equivalent of 2 GCSE’s

What do you do? Deadline is Christmas Complete booklet Complete practical project (Table).

Split up into three sections Health and safety and basic hand tools The use of basic hand tools and their maintenance Manufacture of joinery components using basic joints

Health and safety and basic hand tools Safe use of basic tools (especially those that are sharp) Material storage, lifting methods Identify the use of basic tools

The use of basic hand tools and their maintenance Be able to measure and mark out work and create a cutting list Be able to perform craft operations Proper care in keeping tools sharp

Manufacture of joinery components using basic joints Selection of basic joints Manufacture of a small item (Table)