Use this one when drilling from front

Slides:

Advertisements

Similar presentations

How to check close-to-the-line arrows F E D E R A T I O N I T N E R N A T I O N A L E D E T I R A L ' A R C a b TOP VIEW FRONT VIEW a b c d e c d e.

Advertisements

Protractor Center Hole. Measuring and Drawing Angles with a Protractor By Christine Berg Edited By V Hamilton.

KPL CHINA SOURCING CO., LTD. Mail: Website: FURNITURE.

Following Directions Lesson

Start with a sheet of A4 paper size FOLD the paper on all lines then open up. 2 2.

Michael Long– Eagle Project - Exhibit D-1 Plans/Drawings – Top View

Single-Balanced Mixer Assembly Instructions Revision 2 Updated 5/7/2012.

How to make a Miners Lantern. Developed as part of… SURVIVNG STAVELEY.

This P shaped package is designed this way because P for Penguin. My mouse is a penguin so it kind of explains it.

Reading a Graduated Cylinder And All about the Meniscus.

EML 2023 – Modeling, Assemblies Lecture 3.2 – Assemblies, part 2.

Trim Fwd Spar End Brackets July 6, H2-2, Horizontal Stab Rear Spar 7H1-2, Stab Full Rib Corner of Forward.

Full Ribs to Rear Spar Parts Layout July 6, H2-2, Horizontal Stab Rear Spar with upper and lower doublers.

OR-PR 156 Fabricate a Standard Full Calf Cuff.  Cut a strip of leather 2 1/2” wide and the length of the largest calf circumference + 2 1/2” Largest.

Components Connection Jig Graph Paper (#4101) Mounting Blocks (#5902) Nails Tape Measure Pen Hammer Customer Coordinates.

Fence Construction. What is the Purpose of a Fence? Protection from enemies To keep livestock in or protect from predators To protect a garden from animals.

© T Madas. Mathematical and Technical Drawings Bottom Side (Left) Back Front Top Side (Right)

Air Racer Design and Layout.

Mark a line at the center of the canvas for its entire length. Place frame on a table or saw horses, bottom up.

PRST5450-eTraining presents… Book Repair Issues: “Tipping-In”

Rut ‘n’ Strut Game Calls How I turn a Pot Call. Select wood that you want to use to turn Pot Calls out of, Rip it 4” wide and then Crosscut into 4” X.

3-D Views of Solid Figures

Using the Alphabet of lines. Drawing should be near bottom left corner. The front view shows how wide and how tall the object is.

Agriscience Toolbox Plan of Procedure 1. Table Saw (equipment) Rip the bottom of the toolbox to a width of 10 inches.

Following directions. Design your paper on ONE side.

Lesson 10-2: 3-D Views of Solid Figures 1 3-D Views of Solid Figures Lesson 10-2.

Lesson 11-2 Nets and Surface Area.

Drawings, Nets, and Other Models Drawings, Nets, and Other Models

This is a fold-down clothes bar that will hold up to 12 plastic clothes hangers or even more wire hangers. As I don’t have a trailer wall to put it on,

Final Assignment Air Car Chassis Design using Sketchup.

TRUE MITRE ANGLE in RAKING MOULDS by Greg Cheetham Original square mould along side.

Oneone IN-4 Objective: To construct a catapult or series of catapults in order to test an experimental variable. Core Question: How is the experimental.

Step one: Page Border and title block. Border will be ¼” from the edge of the paper. Drawing will be done in landscape format. Title block will be 1”

12 Steps 1. Wedge 2. Center 3. Drop the hole 4. Check the thickness of base leave ½ inch 5. Undercut base & pull up walls 6. Shape the pot 7. Trim the.

Layout for Fixel Readout Board fiber Holder The FRBH module will provide structure to the fiber assembly in the Fixel Readout system. header Pots, two.

Zero Waste Garment Sewing Instructions

How to Make an Origami Jumping Frog. This amazing origami frog really jumps! When you're done making this amazing frog, you can have a frog jumping contest.

Folding Fold a paper crane Prepare a square paper.

Three View Drawing Technical Drawing and Design Osbourn Park High School Mrs. House.

Draw a net of a triangular prism. What shapes did you use? A. 3 squares and 1 triangle B. 3 rectangles and 2 triangles C. 1 rectangle and 4 triangles D.

Measuring and Drawing Angles with a Protractor. Protractor Center Hole.

Completed Front and Rear Standard 10 ½” 1 ½” 3 ¼” 4 ½” 1” ¾” 1 ½” 6” ¾” Channel Length: 5 ¼”, ¾” from end.

1.2 Drawings, Nets, and Other Models

Board Replacement for Engineered Glue-Down Pattern Plus with a Premier Performance replacement board.

Drawing Alcoves using One Point Perspective

Development of Surfaces

Fire Fire drill.

قراءة القوائم المالية وفـاء شـريف علي. محلل مالي

Making a trap cage.

Whimsical round floral design

How to make a paper aeroplane

Two Point Perspective Widget Walkthrough.

Creating a grid by Carl Dellutri.

Break down Lance rack Cut one of each of these for each rack

Christmas Card Box Marcus P. Dula.

FRONT No Solutions Infinite Solutions 1 solution (x, y)

Can I easily identify all four members of

Reading the Graduated Cylinder

Make your own Rotocopter

3-D Views of Solid Figures

You decide which of the following is:

Miniature Train.

Cylinder Technique Project

Miniature Train Smoke Stack.

QUESTION NUMBER 1.

Drawstring Backpack Instructions

Building pattern  Complete the following tables and write the rule 

Trim along dotted line INPUT RESONANCE Align this to the

Presentation transcript:

Use this one when drilling from front 2 1 3 6 7 8 9 ATTACK 4 10 DECAY SUSTAIN RELEASE Trim along dotted line Pot hole center lines for reference Midway between decay & sustain pot centers ¼” from panel edge Center of panel Center top LED Center bottom LED Use this one when drilling from front

Use this one when drilling from back 2 1 3 6 7 8 9 ATTACK 4 10 DECAY SUSTAIN RELEASE Trim along dotted line Pot hole center lines for reference Midway between decay & sustain pot centers ¼” from panel edge Center of panel Center top LED Center bottom LED Use this one when drilling from back