LESSON-13 STRAIGHT KNIFE CUTTER

Slides:

Advertisements

Similar presentations

Types of saw blades Crosscut –used to make smooth cuts across the grain Rip –used to make smooth fast cuts with the grain Combination –used to make fast.

Advertisements

BARTOSZEK ENGINEERING 1 The Design of the Booster Collimators Larry Bartoszek BARTOSZEK ENGINEERING 3/10/03.

Sewing Tools Assignment

 When using the rotary cutter always walk with the blade closed. To open the blade place four fingers around the handle and slide the blade guard button.

PRESENTED BY: NEHA SAMDANI PRAJJWAL DEWASKAR M.ftech-3 rd sem PRESENTED BY: NEHA SAMDANI PRAJJWAL DEWASKAR M.ftech-3 rd sem.

How to sharpen a horticultural knife. Use a wire brush to remove any resin/deposit on the knife before sharpening.

Introduction to Culinary Arts

Cub Scout Pack 452 Whittling Chip Class

TRU-CUT  For True ease of operation, you can inch along or move at full speed by varying the thumb pressure on the left.  Dual automotive type clutches.

Icing the Cake An Investigation Icing the Cake The diagram shows a cake which consists of three tiers. The diameter of the bottom tier is 40cm. The diameters.

SURFACE AREA and VOLUME of RECTANGULAR PRISMS and CUBES.

Tips and Techniques. Construction Materials Corrugated CardboardDuct Tape up to ½ in. thick any color combined ≤ 1 in. thick on seams only.

Jimmy K.C. Lam The Hong Kong Polytechnic University

Sewing Equipment.

8cm 5cm Area = 8 x 5 = 40cm 2 A parallelogram can be split up into a rectangle and 2 triangles – each with the same area. 10cm 5cm.

Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 15 Woodworking with Power Machines.

Area of Trapezoids Return to table of contents. Area of a Trapezoid ·Cut the trapezoid in half horizontally ·Rotate the top half so it lies next to the.

Many games depend on how a ball bounces. For example, if different basketballs rebounded differently, one basketball would bounce differently off of a.

My Personal Journal Think of your most comfortable garment. What type of garment is it? Describe it below and explain it’s importance to you (why it is.

Lecture 17 Cutting Department. Marker making….  Efficiency of marker = (Area of patterns in marker plan / Total area of the marker plan) X 100.

Specifications and Blade Types OBJECTIVE: give basic facts on the reciprocating saw tool. By: Phuong Dinh Points of Discussion Definitions Types of Reciprocating.

Heat energy Unit2 Lesson 3 Transfer of heat energy.

Presented by Andrew 3/4L Simple Machines. Contents  Lever Lever  Wheel & Axle Wheel & Axle  Pulley Pulley  Incline Plane Incline Plane  Screw Screw.

PRODUCTION PLANNING AND MATERIALS CONTROL

USED IN TROUSERS MAKING

Look at the shapes below. How do I know which ones are pentagons?

Lesson 11.2 Area of Parallelograms and Triangles.

M May Triangles Angles of triangle add to 180˚ * o * o * o Straight angle = 180˚

© Folens 2009 Learning objectives/aims You must: recognize a range of basic equipment. describe how and when equipment is used. You should: should be able.

UNIVERSAL COLLAGE OF ENGINEERING & TECHNOLOGY

Cam and Follower The cam and follower is a device which can convert rotary motion (circular motion) into linear motion (movement in a straight line). Cam.

Intro to the Sewing Machine. 1. Stitch Plate Where the seam allowance guidelines are found. Each line is 1/8” apart, beginning with the inside edge of.

Pre-Algebra Point-Slope Form. Learn to find the equation of a line given one point and the slope.

Reciprocating Saws Objective: Provide a general understanding of reciprocating saws and their use. By: Derek Landschoot References:

The Blades and Motor Presented by Jeffrey Wu. Objective: To understand the blades and the motor of a reciprocating saw. Definition: A portable power saw.

Industrial Machinery.  The machine opposite is a lock stitch machine.  It only does a basic straight stitch.  Different specialist machines do other.

In this lesson you are going to learn how to divide fractions by multiplying by the reciprocal.

Print Making 101 By Mrs. Peachee.

PostBase Automatic Feeder Component Removal Service Training

What is the Cam? A Cam is a rotating or sliding piece in a mechanical linkage used especially in transforming rotary motion into linear motion. A cam may be defined as a rotating machine part designed to.

Cams are used to convert rotary motion into reciprocating motion

CAMS WITH SPECIFIED CONTOURS

Surface Area of Rectangular Prisms

continued on next slide

T400 Motor Replacement.

FILL IT UP!! FILL IT UP!! FILL IT UP.

continued on next slide

continued on next slide

PHONE Case Design brief:

Pam Eckert ota 210 November 12, 2012

Using a histogram to estimate the median

Using a histogram to estimate the median

Which Tape Is Stickiest?

Cams and Followers.

Obj. 4.01a Key Terms & Questions

Components of a Reciprocating saw

How many links? Linkage examples.

COMMERCIAL MANUFACTURING PRACTICES

BASIC TECHNOLOGY YEAR 7.

Knife Skills mise en place

Structures and Mechanisms.

9.4 Multiplying & Dividing Rational Expressions

continued on next slide

Finding missing side -triangle.

kitchen By using “Slide Show” “Custom Slide Show”,

continued on next slide

Presentation transcript:

LESSON-13 STRAIGHT KNIFE CUTTER STRAIGHT KNIFE CUTTER IS VERY USEFUL IN GARMENT INDUSTRIES A HANDLE FOR THE CUTTER TO DIRECT THE BLADE,AND A SHARPENING DEVICE.

THE BASE PLATE ON ITS ROLLERS SLIDES UNDER THE GLAZEDPAPER WHICH IS SPREAD BELOW THE BOTTOM PLY OF FABRIC IN THE LAY. TWO KINDS OF POWER ARE REQUIRED TO OPERATE A STRAIGHT KNIFE. 1.MOTOR POWER 2.OPERATOR POWER

MOTOR POWER DRIVES THE RECIPROCATING BLADE. OPERATOR POWER DRIVES THE KNIFE THROUGH THE LAY. BLADE HEIGHT VERY FROM 10C.M TO 33C.M. STROKES VERY FROM 2.5C.M TO 4.5C.M.