Overview of Imaging and Tip Placement Procedures Craig Steffan

Slides:

Advertisements

Similar presentations

Build Your Own Future RC2 Serviceability. Build Your Own Future Safety and Ground Rules Before servicing, always remove A/C power from the unit and disconnect.

Advertisements

DS1000B-RM/ DS1500B-RM Battery Replacement Procedure.

Thread Cutting Part 2: Cutting an external thread.

Click on this image to open the full PDF document.

ES1000C/1500C Battery Replacement Procedure. 1.Pull off the front panel.

MP Prototype 2 1IWF-EXP/ÖAW GRAZ  Smaller Size  Outcome of the test results with MP-P1 was the need for a reduced cross section  Rectangular Shaped.

1 © 2011 Profile Recorder for ProtoFlow S Installation Instruction.

Scanning Tunneling Microscope How to use the STM Developed by Malory M. Peterson, Summer 2006 Nanotechnology Grant National Science Foundation #

Overview Test Interface (TIU PCB‘s) are extremely expensive.

Procedure for Pro4 using Keithley

Parts of a Compound Light Microscope. Mirror / Light the light source for a microscope, typically located in the base of the microscope. Most light.

MICROSCOPY Ken Leach Collins Hill High School. What do microscopes do? The forgotten Technology An optical instrument that uses a lens or a combination.

Removing and Replacing the Battery Cover 1. Ensure the phone is turned off. 2. Press the Battery cover locker; lift the battery cover up and away from.

Nanonics CryoView 2000™ CryoView 2000™ Product Presentation.

2G BBULBE PASS Instructions-5 Replacement of Heater.

Parts of the Microscope Notes. Arm: This part supports the entire upper portion of the microscope.

Figure 3.1. Schematic showing all major components of an SPM. In this example, feedback is used to move the sensor vertically to maintain a constant signal.

First you start off with a square piece of paper and lay it out on the blank side.

MultiView 1000™ Product Presentation Nanonics MultiView 1000™

Periodic Table Project Your 8 th grade class will design a periodic table together. You are responsible for designing 1 piece of the table. This is what.

PS2200B/3000B Battery Replacement Procedure. 1.Disconnect the wire connecting the UPS and the battery pack. 2.Pull off the battery pack front panel.

1 PST Heaters – Proposed Segmentation Forward = 2289mm. 6 hoops. 10 heaters Barrel = 1606mm. 4 hoops. 7 heaters.

Replacing the Main Monitor 1.Open Lower Main Door, and turn off machine power 2.Open the upper main door 3.Disconnect the video and power plugs from the.

1 Report SThM AFM LAB. SThM Signal vs Time. The SThM signal was recorded directly from the tip. At the same Time and incandescent light bulb was used.

Microscopes Kinds Light –Image illuminated from bottom in most, top in a few. –Magnifies from times. –Can see individual cells and a few organelles.

HANDLING, OPERATION & CARE OF THE LIGHT COMPOUND MICROSCOPE PRACTICAL 1.

Prepared By: Ms. Carolyn R. Magat

Veterinary Practice Laboratory

Activity 35- A License to Learn

Compound Microscopes and Lab Techniques

ATLAS pixel module assembly flow

X-Spot Lamp Socket Replacement Procedure

Check the focal distance of the lens

Tool Assembly Procedure

MICROSCOPE BASICS.

How to Use a Microscope.

Parts and Functions of a Microscope

Microscope Close-Out Photos

Setting up a trinocular compound microscope for best viewing

Start on the corner of your picture *(Not the corner of the paper)

The Compound Microscope

ZPS Foot & Ankle Display

nSW Alignment Installation

Immediate implant placement and function in the anterior region (cement-retained) – Hands-on presentation Disclaimer: Some products may not be regulatory.

Microscope Basics.

Parts of the Compound Light Microscope

Microscope 8/22/17.

Adjusting Tilt and Turn Inswing Door or Window

How to use a ….. Microscope.

Life-sustaining processes and survival of species

(Preliminary) WIYN 0.9 Meter Collimation Procedure

Replace fan motor MullToa 45 and 60

STRUCTURE AND FUNCTION

Microscope Intro Honors Bio.

Microscope Basics.

FOCUS! Hold microscope close

The Compound Microscope

909 3/4”-2”.

Volume 8, Issue 12, Pages R243-R246 (December 2000)

Molecular Imaging System

Gattini Detector Installation

Illumination Optics Design for DLP470TP with SBM-40-LC LED

Microscopes Learning Objectives: Define the term “microscopic”.

REPLACING ECONOMIZER ACTUATOR MODULE

Rule of Thirds.

Warm-Up, top of page 8 How does knowing how to use a microscope help me in Living Earth?

Repair Guide SYM XT Series.

Fix your Fireplace SYM-B Series.

Presentation transcript:

Overview of Imaging and Tip Placement Procedures Craig Steffan UT Meeting 04/05/2001 Overview of Imaging and Tip Placement Procedures Craig Steffan

IFM Optical Mount Components Piece 1 - Coarse focus and positioning. Applies the same design for the IFM head. Piece 2 - Connects Peak Microscope to piece 1. Peak microscope threads onto the top portion, three screws connect it to piece 1. Illumination - Provided by optical fiber.

Other Components Positioning reticle - Whipple grid 100 squares in a 7 mm square area.

IFM Optics Mount Piece 2 Piece 1

IFM Optics Mount

IFM Imaging Procedure Place whipple grid on sample holder. Image 5 um square at a corner with IFM. Remove IFM head and replace with optical head. Place optical reticle on 5 um square corner Replace positioning reticle with sample.

IFM Imaging Procedure Move the sample to the desired testing location. Remove optical head and replace with IFM head. Image sample or begin force/creep profile.

Tip Placement Apparatus Z-stage X-Y Stage

Tip Placement Apparatus

Tip Placement Procedure Place sensor on X-Y stage. Place tip in forceps and connect to z-stage. Carefully apply epoxy to tip base and desired sensor position. Move tip into contact with the sensor. Turn on cartridge heater. (Not pictured)

Tip Placement Procedure After curing gradually lift (approx. 1 mm) the sensor off the X-Y stage. Disconnect forceps from the tip.