Revise No. 1.

Slides:



Advertisements
Similar presentations
MRS SITI KAMARIAH MD SA’AT ERT252 GEOMATIC ENGINEERING.
Advertisements

TRAVERSING Computations.
Errors and Horizontal distance measurement
Distance Measuring.
Types of angles A Z MLN – Horizontal angle ALM – Vertical angle
1 EDM Calculations ASM 215 EDM CALCULATIONS. 2 EDM Calculations HORIZONTAL DISTANCE MEASUREMENT n In plane surveying, the distance between two points.
Chemical Department. Guided by- prof D.M Prajapati. Prof. J. M. Jadav
1.Meet B Parmar ( ) 2.Swapnil A Parmar ( ) 3.Pratik C Patel ( ) B.E- 2 SEM MECHANICAL ENGINEERING LINEAR MEASUREMENTS.
CHAPTER 4 Coordinate Geometry and Traverse Surveying
Islamic University of Gaza Civil Engineering Department Surveying II ECIV 2332 By Belal Almassri.
ANGLE AND DIRECTION MEASUREMENT
Distance Measuring. Two principles of measuring distance 1) It takes two points to form a line. 2) The shortest distance between two points is a straight.
BALANCING A GOVERNMENT MEANDER LINE USING STATE PLANE COORDINATES
Triangulation and Trilateration
Slope of a Line Section 1.3. Lehmann, Intermediate Algebra, 3ed Section 1.3Slide 2 Introduction Two ladders leaning against a building. Which is steeper?
Surveying Chain Surveying
Coordinate Geometry and Traverse Surveying Faculty of Applied Engineering and Urban Planning Civil Engineering Department Lecture 8 - Week 5 2 nd Semester.
Leveling Chapter 4. Why do we perform leveling surveys? To determine the topography of sites for design projects Set grades and elevations for construction.
Roofs The exterior upper part of a house or building – to protect the interior from the elements (heat, cold, rain, snow etc.)
Air Pressure Read the lesson title aloud to students.
TOPIC 5 TRAVERSING MS SITI KAMARIAH MD SA’AT LECTURER
Given: DB bisects AE
By: Student #2. Four properties  Equidistant  Have same slope  Do no intersect  Lies on the same plane.
Chap 7 – Differential Leveling
5.8 Problem Solving with Right Triangles Angle of elevation horizontal line of sight Angle of depression line of sight.
Teaching the Rising Generation about our Profession.
WHITEBOARD PRACTICE FINDING THE MISSING ANGLE IN AN ANGLE PAIR.
COURSE PLAN Department of mining engineering, University of engineering & technology, lahore.
Objective To use angles of elevation and depression to solve problems.
Measurement Counting yields exact numbers Measuring yields inexact values Always some error Your job is to minimize it.
SURVEYING II (CE 6404) CONTROL SURVEYING UNIT I By Mr.R.GOPALAKRISHNAN, Asst.Professor in Civil Engineering, Sri Venkateswara College of Engineering.
Using Tangent The angle formed by a horizontal line and a line of sight to an object above the horizontal line. You can use the angle of elevation as.
In Compass survey chain or tape is used for linear measurements and compass is used for fixing direction. In compass freely suspended.
Surveying Equipment. Builder’s Level A telescope instrument used to check level of forms or field grades. Builders' levels are designed to be used for.
Submitted By: Mon Alfred B. Cabia Submitted To: Roberto Cabrera.
Finding the slope of a Line
Chapter (4) Traverse Computations
Chain surveying Notes.
Government Engineering College, Bhavnagar Civil Engineering Third Sem
Random Error Propagation
We have started to compute the traverse station
BASIC DISTANCE MEASUREMENT
Surveying Equipment.
Moments.
Lesson 6.5 Percents of Increase and Decrease
A percent, a whole, and a part
Angle, Distance, Traverse, and Leveling Errors
Angle of Elevation & Angle of Depression
Angles and Directions.
Angles and Directions.
LINEAR MEASUREMENT-PART 1
TRIANGLES Find the missing angles. Can these sides form a triangle?
Distance Measurement.
Distance Measurement.
Angles and Directions.
Angles and Directions.
Objective Solve problems involving angles of elevation and angles of depression.
Surveying With Construction Applications, 7th Edition
Linear Measurement NG1H703 & BE1S204 David Harper.
Angles and Directions.
Theodolite - Instrument Checks
Angles and Determination of Direction
Random Error Propagation
Revise No. 1.
Latitudes and Departures
Slope 3.5 Rate and Slope Horizontal and Vertical Lines Applications.
Revise No. II.
Taping Taping.
TRAVERSING.
Taping Taping.
Presentation transcript:

Revise No. 1

Q1) Answer the following statements (T) or ( F) : a- A sag error can be eliminated by decreasing the applied tension. b- c- A 3.63- percent slope is one that rises 10.08 m in 277.77 m. c- The slope distance between two points is 17.277 m and the slope angle is 1042/. The horizontal distance is 0.512 m.

Q2) Station 2+04. 67 must be marked in the field Q2) Station 2+04.67 must be marked in the field. If the steel tape to be used is only 99.98 m (under standard condition). How far from the existing station mark at 0+79.23.

Q3) find the Elevation of point C. Given : H. I = 5 Q3) find the Elevation of point C. Given : H.I = 5.51 m , instrument fixed above point B

Q4) A closed property traverse has the following data, compute the missing data

Q5) closed traverse consist of three courses Q5) closed traverse consist of three courses. From the following data , find the Azimuth angle of Course AC. BRGAB = N 50o 00/ 00// E BRGBC = S 20o 00/ 00// E LAC= LBC

Q6) closed traverse consist of three courses Q6) closed traverse consist of three courses. From the following data , find the internal angle IJK

Q7) closed traverse consist of three courses Q7) closed traverse consist of three courses. From the following data , find the error of closure

Q8) closed traverse consist of three courses Q8) closed traverse consist of three courses. From the following data , find the departure of the course DA. Error of closure = 0.54