Back of tub 794 mm (31.25”) 654 mm (25.75”) 06-Jan-06 F.E.Taylor.

Slides:



Advertisements
Similar presentations
Drawing In One-Point Perspective
Advertisements

Using Algebra Tiles to Write an Expression as a Product or Sum

Drafting – Product Design & Architecture
Basic Setting Out.
2x2 module & stave layouts. 2 options “Small chip” “Big chip” Boundary between “small” and “big” is determined by the 6” sensor wafer layout that must.
One-Point Perspective Part II – The Sequel. Step 1 Begin with a simple room (just like last time) Draw a flat door.
Components Connection Jig Graph Paper (#4101) Mounting Blocks (#5902) Nails Tape Measure Pen Hammer Customer Coordinates.
Lines Identifying Different Types of Lines. LINES There are many different types of lines. Can you think of any? vertical horizontal diagonal perpendicular.
Drafting Rear Elevations. Start with outer frame when drafting standard flat. Heights are generally in multiples of 2’-0”. Outer Frame.
FLOORSFLATSTOTAL AREA FIRST SECOND THIRD ST, 2 ND & 3 RD FLOOR PLAN FLOOR PLAN OF 2 BHK LUX. APARTMENT ON PLOT NO.
First displayed at 2007 Fall Mega Event Plating the Gambia d Postage Stamp.
Aberdeen Grammar School
Hexagons & Hexagonal Prisms. Hexagons Hexagons are 6 sided shapes. Hexagons can be dimensioned in 2 different ways. 1. Across the faces. 2. Across the.
Ria Thompson, DenDesignery UNDER-STAIRS BUILT-IN STORAGE CONCEPT CADL03/6207, HND Stage 1, Final.
Elevations, Layout and Drawing Technique.
Using the Alphabet of lines. Drawing should be near bottom left corner. The front view shows how wide and how tall the object is.
J.Byrne Draw the outer shape of the room to sizes given. J.Byrne
Chapter 23 Elevation Layout and Drawing Techniques.
EDT Elevations1 Weekend Cabin Retreat Project Elevations Sacramento City College EDT 300/ENGR 306.
22 Elevations Chapter Permission granted to reproduce for educational use only.© Goodheart-Willcox Co., Inc. Introduction to Elevations Elevation –An.
Drawing a Bed in One-Point Perspective The red lines show the height and width of the bed. The vertical red line shows the side of the bed against the.
RAKING MOULDS by Greg Cheetham. Start with an original mould with square corners as it will sit in the square corner of the side wall and raked ceiling.
EDT Cabin Design Project - Elevations1 Weekend Cabin Retreat Project Elevations Sacramento City College EDT 300 Kenneth Fitzpatrick, P.E.
Multiview Drawing A multiview drawing is one that shows two or more two-dimensional views of a three- dimensional object. Multiview drawings provide the.
17/02/03Designed by Barry Forbes Graphic Communication Hexagons & Hexagonal Prisms.
Hexagons & Hexagonal Prisms.
ROOFS CHAPTER 7. ROOF SHAPES: GABLE ROOF SHAPES: HIP.
The reading is 7.38 mm. The reading is 7.72 mm.
Hexagonal Prisms Developments.  A development is a flat template of a 3D shape that when folded up in the correct way makes the actual shape of the 3D.
SWIMMING POOLS CONSTRUCTED AND REPAIRED
Neutrino v2.1 structural assessment
Interior Wall Coverings
February 27, 2007 Drill – ELEVATIONS
Plating the Gambia d Postage Stamp
Elevation Layout and Drawing Techniques
Sneed Property th Ave E, Puyallup Exterior of House
Mrs. RESHMA RAJ AP/CIVIL ENGINEERING DEPARTMENT OF SCD
PERSPECTIVES & ELEVATIONS
Forging new generations of engineers
Engineering drawing Every language has its own rules of grammar.
Animated picture changes during motion path (Advanced)
Beam Rafter with Assembly of two roof surfaces and Window
Projections Orthographic drawings – drawings where three views of an object are drawn in perpendicular planes to one another.
How to Draw Cones & Cylinders
Fold green paper in half, by width, keeping crease at the top…
Let’s start at where we left out just now
Measuring Instruction for Outdoor Bamboo or PVC Blinds
Carlisle Station : Suggested Improvement Works to Passenger Facilities
Break down Lance rack Cut one of each of these for each rack
The Framers Gallery FRONT CENTER KITCHEN ENTRANCE BACK WC
Sketching Multiview Drawings
My friend measured and said this beam is below where the extra studs need to be placed in the room above. That wire coming out is the wire from the outlet.
Surface Area.
Wall and Ceiling Construction
Creating Elevations from a floor plan
Graphic Communication
Print Reading.
Label: Horizon, Vanishing Point, Vertical, Horizontal
Forging new generations of engineers
Road to Civil War booklet directions
Sketching Multiview Drawings
Difference between 3 COF and 6 COF Open cells in 22” Segment
Sketching Multiview Drawings
Projections Orthographic drawings – drawings where three views of an object are drawn in perpendicular planes to one another.
Identifying Different Types of Lines
Three Dimensional Problems
Elevations, Layout and Drawing Technique.
Forging new generations of engineers
Observations: 70 bacteria colonies. Some are yellow, most are off-white. The yellow and most of the white colonies have smooth edges. They are raised.
Presentation transcript:

Back of tub 794 mm (31.25”) 654 mm (25.75”) 06-Jan-06 F.E.Taylor

Front of tub 699 mm (27. 50”) 654 mm (25.75”) Top of tub 06-Jan-06 F.E.Taylor

Bottom of beam to top of tub Back of tub Beam to top of tub 1575 mm (62”) Bottom of beam to top of tub 1581 mm (62.25”) Corner to outer edge 794 mm (31.25”) Tile wall-to-wall 1575 mm (62”) 06-Jan-06 F.E.Taylor

Front showing ventilator Front tile wall to back tile wall 1575 mm (62”) Height of bottom of ventilator above top of tub 1321 mm (52”) 06-Jan-06 F.E.Taylor

Detail of tile 108 mm (4.25”) 108 mm (4.25”) 06-Jan-06 F.E.Taylor

Notes Suggest making tile height above tub extend to bottom of ventilator – but could go higher to bottom of ceiling beams Cork board will probably have to be removed to glue tile to wall Dimensions approximate Color of tile ‘white’ Thanks very much! 06-Jan-06 F.E.Taylor