S1 Orthographic Sketching

Slides:

Advertisements

Similar presentations

Technical Sketching and Drawing

Advertisements

1 of 4 LESSON #13 A REVIEW OF ORTHOGRAPHIC PROJECTION

SURFACE AREA and VOLUME with BASE 10 BLOCKS

THINKING SKILLS Year 9 Graphics. What method of drawing am I thinking of? 1. 2 dimensional drawing? 2. Isometric Projection? 3. Orthographic Projection?

The Other Side Product Design Sketching Activity.

EXAMPLE 1 Use the net of a prism Find the surface area of a rectangular prism with height 2 centimeters, length 5 centimeters, and width 6 centimeters.

Isometric and Orthographic Projections

Orthographic to Isometric

Sketching Practice “One picture is worth a thousand words.”

Dimensioning Dimensioning Gateway To Technology®

Orthographic Drawing.

Greenfaulds High School Orthographic Views. Orthographic Projection Orthographic projection is the name given to the type of drawing where a 3D object.

Holt Geometry 10-2 Representations of Three-Dimensional Figures Warm Up Write a description of each figure. 1. cube 2. pentagonal prism 3. cylinder prism.

Using Drawings to Communicate Lecture 3 –How to create an isometric drawing of a part when given front, top, & right side views.

Drawing Unit Orthographic Projection P. Hennessy

Sketching Multiview Drawings

Area & Perimeter An Introduction. AREA The amount of space inside a 2-dimensional object. Measured in square units cm 2, m 2, mm 2 Example: 1 cm 2 cm.

Tuesday 3:15-4:30. Homework Check pp

Pictorial Drawing Isometric.

3-view drawings. orthographic projection 3-view drawings 3-View Drawings will depict 3 views of a 3 Dimensional Object. 3-View Drawings show: height,

Graphic Communication.  Auxiliary views are additional views that are used in orthographic projection.  Auxiliary views are normally used to view the.

EXAMPLE 3 Find the area of an isosceles triangle

1.2 Drawings, Nets, and Other Models

Isometric & Orthographic Drawings

Nets and Drawings for Visualizing Geometry

Deans Community High School

Section 1.1 – Nets and Drawings for Visualizing Geometry

Representations of Three-Dimensional Figures

September 10, 2009 DRILL Answer the following in complete sentences:

Introduction to Agriculture, Food, and Natural Resources

Area – Perimeter - Volume

Forging new generations of engineers

Orthographic Projection

Orthographic Projection & Line Types

First and Third Angle Projection.

WORKING DRAWINGS Footer Text 11/14/2018.

Isometric Projection -the term ‘isometric’ comes from the Greek for ‘equal measure’ reflecting the scale along each axis is the same - Isometric views.

Projections Orthographic drawings – drawings where three views of an object are drawn in perpendicular planes to one another.

Multi-View Sketching STEM Foundations Multi-View Sketching

2D or Not 2D Technical Drawing Workshop: Orthographic Views

I can make Orthographic drawings

Oblique Pictorials Introduction to Engineering DesignTM

نجاح وفشل المنشآت الصغيرة

ENGN103 Engineering Drawing

Orthographic Sketch Solution

Technical Drawings Sketch by Leonardo DaVinci. 500 years ago.

7.G.5 Surface Area of a prism

Auxiliary Introduction

Sketching Multiview Drawings

ENGN103 Engineering Drawing

Forging new generations of engineers

Sketching Multiview Drawings

Orthographic Views of Solids

ENGN103 Engineering Drawing orthographic projections

Orthographic Projections

Visualizing Geometry Skill 01.

ENGN103 Engineering Drawing orthographic projections

2-D Representations of Solids

ENGN103 Engineering Drawing

Sketching Multiview Drawings

ENGN103 Engineering Drawing orthographic projections

What is area? The amount of space that a figure encloses

Projections & Technical Drawing

Projections Orthographic drawings – drawings where three views of an object are drawn in perpendicular planes to one another.

~ Chapter 7 Section 3 Polygons are similar if: (Similar Polygons)

Introduction to Orthographic Projections

Orthographic Projection:

How many 3D shapes can you list?

Forging new generations of engineers

1.2: Drawings, Nets, and other models

Presentation transcript:

S1 Orthographic Sketching

INTRODUCTION Orthographic drawing is a way of drawing a three dimensional object. Normally the object is drawn as three separate, related views - Front View, Side View and Plan View.

BLOCK 1 Draw the Front View, Top View and End Views of the block. 4 Draw the Front View, Top View and End Views of the block. The block has a length of 10 squares, a height of 6 squares and a thickness of 4 squares. 10 6 6 2

BLOCK 1 – ANSWERS

Block 2 Draw the Front View, Top View and End Views of the block. 3 3 Draw the Front View, Top View and End Views of the block. The block has a length of 10 squares, a height of 6 squares and a thickness of 4 squares. 3 6 10 4

BLOCK 2 - ANSWERS

10 6 3 4 Block 3- HOMEWORK Draw the Front View, Top View and End Views of the block. The block has a length of 10 squares, a height of 6 squares and a thickness of 4 squares.

BLOCK 3 - ANSWERS

BLOCK 4 Draw the Front View, Top View and End Views of the block. 2 BLOCK 4 Draw the Front View, Top View and End Views of the block. The block has a length of 10 squares, a height of 6 squares and a thickness of 4 squares. 2 7 10 4

BLOCK 4 - ANSWERS

BLOCK 5 Draw the Front View, Top View and End Views of the block. 1 BLOCK 5 10 Draw the Front View, Top View and End Views of the block. The block has a length of 10 squares, a height of 6 squares and a thickness of 4 squares. 1 6 4

BLOCK 5 HOMEWORK - ANSWERS

BLOCK 6 – HOMEWORK 2 4 6 Draw the Front View, Top View and End Views of the block. The block has a length of 10 squares, a height of 6 squares and a thickness of 4 squares.

BLOCK 6 HOMEWORK – ANSWERS

BLOCK 7 Draw the Front View, Top View and End Views of the block. 10 4 1 2 3 Draw the Front View, Top View and End Views of the block. The block has a length of 10 squares, a height of 6 squares and a thickness of 4 squares.

BLOCK 7 - ANSWERS