SCX-4521F/SCX-4321 Series training

Slides:



Advertisements
Similar presentations
Introduction to PIC Microcontrollers
Advertisements

SCX-6X22 Series training JULY 2006 SCX-6X22 Series training JULY 2006 Mechanism.
Programmable Interval Timer
LOGO.  Concept:  Is read-only memory.  Do not lose data when power is lost.  ROM memory is used to produce chips with integrated.
In this presentation you will:
Oscilloscope Watch Teardown. Agenda History and General overview Hardware design: – Block diagram and general overview – Choice of the microcontroller.
Basic Input Output System
Memory Chapter 3. Slide 2 of 14Chapter 1 Objectives  Explain the types of memory  Explain the types of RAM  Explain the working of the RAM  List the.
Motion Tracking Recorder 360 (MTR-360) Group #1 Lee Estep Philip Robertson Andy Schiestl Robert Tate.
Critical Design Review The Lone Rangers Brad Alcorn Tim Caldwell Mitch Duggan Kai Gelatt Josh Peifer Capstone 2007.
Copier Jam Detector Design Problem
ASPPRATECH.
Introduction ‘Have you ever played video games before? Look at the joystick movement. When you move the joystick to the left, the plane on the TV screen.
Microcontroller: Introduction
Engineering 1040: Mechanisms & Electric Circuits Fall 2011 Introduction to Embedded Systems.
Fill in the blanks on your note.
Introduction ► Scope:- Service Diagnostics Routines can use for XXL, Side by Side products with STEALTH user interface with single evaporator fan product.
Mother Board MOTHER BOARD Holds CPU, memory, PCI bays, etc.
AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER
Training (H/W) [ML-5510N/ ML-5510ND/ML-6510ND ML-5512ND/ML-6512ND
Objectives How Microcontroller works
Training (S/W) 상품화 개발 2G Samsung IT Solutions Business Nov [ML-5510N/ ML-5510ND/ML-6510ND ML-5512ND/ML-6512ND.
COE4OI5 Engineering Design Chapter 2: UP2/UP3 board.
Renesas Electronics Europe GmbH A © 2010 Renesas Electronics Corporation. All rights reserved. RL78 Clock Generator.
Introduction to Computing: Lecture 4
Random access memory.
System Clocks.
Organization of a computer: The motherboard and its components.
Introduction to Computers
The Basic Input/Output System Unit objectives: Access the BIOS setup utility, change hardware configuration values, and research BIOS updates Explain the.
Exercise 2 The Motherboard
MOBILE OPERATING ROBOT ON EMBEDDED SYSTEM
Zach Molden Shamlan Al-Roomi NJ Purevsuren Raied Farash Aadiel Rizvi C ritical D esign R eview.
Circuits, Gigabyte, RAM, Silicon Chips, Storage Devices Made of melted sand and that is what circuits are embedded into to keep them together. The ability.
8279 KEYBOARD AND DISPLAY INTERFACING
Computers Are Your Future Chapter 1 Slide 1 Introduction to the Computers & Internet Chapter 1 Concepts of Information Technology IT.
Basic Input/Output System
L2000 Technical Training 5. Installation and Servicing.
PRIYADARSHINI SHRAVYA KAVYAA MOBILE CONTROLLED ROBOT USING DTMF ALLPPT.com _ Free PowerPoint Templates, Diagrams and Charts.
Automatic accident avoiding system PROJECT MEMBERS MUTHUKUMAR.K (05ME33) SAKTHIDHASAN.S (05ME39) SAKTHIVEL.N (05ME40) VINOTH.S (05ME56) PROJECT GUIDE:
CLX-3170 Series training. Agenda I.General Specification I.Product Overview II.Product General Specification III.Review II.Feature Details I.UI (Control.
8254 Timer.
CLX-6240FX & CLX-6200FX series Hardware.
OBSTACLE AVOIDANCE ROBOT
8279 KEYBOARD AND DISPLAY INTERFACING
Digital Printing Division Elbert & Elbert-P Changes 11.Aug
Digital Printing R & D 1 group Feb 2008 Education of CLP-310/310N.
Ⅰ. PS Driver ML-4050N Series PostScript, Driver ML-4050N Series PostScript, Driver.
Firmware (CLP-310 Series).
Engine & EDC Training June I.Engine II.LSU Error III.Heat Error IV.EDC Mode Agenda.
Chapter 2 HAEDWAER.
Digital Literacy: Computer Basics
Parts of a Computer. Keyboard: The input device that you use to type letters, numbers, and symbols into a computer.
SCX-4828FN & 4824FN Hardware SCX-4828FN & 4824FN Hardware.
Lesson 2 Component Overview Core Hardware Fundamentals.
Computer Basics Just How Does a Computer Work?
BITS Pilani Pilani Campus Pawan Sharma ES C263 Microprocessor Programming and Interfacing.
WATER LEVEL INDICATOR AND AUTOMATIC MOTOR SWITCHING SYSTEM
Mobile phone keypad sensed password entry for door opening.
Voice Controlled Robot by Cell Phone with Android App
Programming Concepts (Part B) ENGR 10 Introduction to Engineering
Arduino Based Industrial appliances control system by decoding dual tone multi frequency signals on GSM / CDMA network. Submitted by:
ARDUINO BASED AUTOMATIC TEMPERATURE BASED FAN SPEED CONTROLLER
PROPELLER DISPLAY OF MESSAGE BY VIRTUAL LEDS
ARDUINO LINE FOLLOWER ROBOT
Parts of a Computer I plan to use this presentation for an introduction at the start of the year. Maybe even create a “word wall” with the cards.
Programming Concepts (Part B) ENGR 10 Introduction to Engineering
The bios.
Programming Concepts (Part B) ENGR 10 Introduction to Engineering
Presentation transcript:

SCX-4521F/SCX-4321 Series training Hardware June, 2005

Agenda Overview Block Diagram Connection Diagram Schematic – Key concept Front Cover and Jam Cover open Toner Cartridge Tech mode

Ⅰ. Introduction 1. Overview SMPS Main Board ADF Board OPE Board HVPS LIU Board

Ⅰ. Introduction 2. Block Diagram of SCX-4521F

Ⅰ. Introduction 4-1. Main PBA - II CPU – Chorus2 Chorus2(S3C46Q0X) is developed using ARM7TDMI core, 0.18um CMOS standard cell 1.8V internal, 3.3V external(I/O boundary) Voltage used. 16bit/32bit RISC architecture and 16bit external data bus. Image processor included. On-Chip clock generator with internal PLL. USB Device(Ver 1.1) interface controller included. Parallel Port Interface controller included. Operating frequency 66MHz ( converting 10MHz main clock to 66MHz operating clocl using internal PLL )

Ⅰ. Introduction 4-1. Main PBA - III SDRAM – 8MB * 2ea Flash ROM – 2MB Two SDRAM chips (Max operating frequency : 133MHz) are used each SDRAM has 8MByte memory capacity. SDRAMs operates 66MHz which is the same as CPU’s operating frequency. Flash ROM( Nor flash ) has 2MB memory capacity and its access time is max. 70ns. Firmware is stored in the FlashROM this can be upgraded by user. When upgrading F/W, never turn off the power until completing upgrade process. If the user turn off the power while upgrading F/W, the program code will conflict and the machine will not work. If above situation occurs, replace the Main PBA. Flash ROM – 2MB

Ⅰ. Introduction 4-1. Main PBA - V Engine Motor Driver (A3977SLP) A3977SLP is a stepping motor driver IC with integrated step and direction translator interface. Direction Pin is tied to Vcc(High level) because the engine motor always rotate only one way. Stepping resolution Pin(MS1, MS2) tied to GND there is no need to control any other resolution except Full-Step. Current setting of the motor current is about 1.3A peak. Output voltage and output current of the A3977SLP appears like left side image (oscilloscope waveform) Vout Iout

Ⅰ. Introduction 4-1. Main PBA - VI Platen Motor driver (TEA3718) TEA3718 is a stepper motor driver IC. TEA3718 IC uses a pair of outputs, and stepper motor needs 2pairs of outputs, so 2 ICs used for driving platen motors. Platen motor can be driven forward or backward direction and full-step, halt-step, quarter-step resolution by controlling 6 control inputs based on pre-defined control sequence. Platen motor driving current is 0.5A on peak level. Platen Motor driver (TEA3718)

Ⅰ. Introduction 4-1. Main PBA - VII EEPROM – M24C04 SCX-4x21 series has EEPROM in order to store environmental datum, total page count data, dot counter data, etc… M24C04(4Kbit) EEPROM device is used. Read/Write operation is activated when the machine states go idle. While printing, Copying, scanning or FAX transmitting, EEPROM read/write operation not activated. Because of this, if the user turn the power off right after the printed page has exited, there is no time for writing newer data therefore dot count and page count data will not be updated. Machine requires 2sec for updating EEPROM data after final page exit.

Ⅰ. Introduction 4-1. Main PBA – Differences between 4-in-1 and 3-in-1 2 1 SCX-4521F Main Board SCX-4321 Main Board SCX-4521F is a 4-in-1 machine, while SCX-4321 is a 3-in-1. SCX-4321 has no FAX function. SCX-4521F and SCX-4321 has basically the same PCB, but some parts which related on FAX function are different. The different parts between SCX-4521F and SCX-4321 are marked above picture. See area marked ( ). Parts relating to FAX function and speaker function are not mounted on the board. The Battery back-up function and RTC(real time clock) function have also been deleted on the SCX-4321 compared with SCX-4521F. (The crystal resonator used for the RTC function is also not mounted . See box marked ) 1 2

ADF Motor Driver IC – TEA3718 Ⅰ. Introduction 4-2. ADF PBA - I ADF Motor Driver IC – TEA3718 ADF Motor drive IC is used TEA3718 – the same part as used in platen motor driver. ADF Motor driving current is about 0.8A peak.

Ⅰ. Introduction 4-2. ADF PBA - II Photo Sensor 2 3 1 3 photo sensors exist on the ADF board. The first sensor- marked 1- detects whether the original document is on the ADF or not. The second sensor- marked 2 – detects the position of the original document for registration. The third sensor – marked 3 – detects the position stating scanning of the original document. If something prevent emitted ray from reaching base of the photo TR, sensor output goes High level, and if there is nothing interruptting emitted ray to photo TR, sensor output goes Low level.

II. Summary of Product 4-5. SMPS PBA - I SCX-4521F SMPS is almost same as ML-2010/2015. The only difference between SCX-4521F and ML-2010 is 24V output current. ML-2010 : 2.0A for 24V output SCX-4521F : 2.5A for 24V output On the SMPS board, Jam cover switch and paper-regi sensor exists.

II. Summary of Product 4-6. HVPS PBA - I PAPER-EXIT SENSOR HVPS board is exactly the same as ML-2010/2015 priter machine. SCX-4521F does not use SW2, LED1 and LED2. but they still places because they are used on ML-2010/2015. Two photo-sensor s take place – Paper empty sensor and paper exit sensor Cover open sensor is on the board.

II. Summary of Product 5. Front Cover & Jam Cover Open Sensing SMPS There are two user protection switches on this unit. If either of the two switches are opened, the +24V for DC fan, solenoid, main motor, polygon motor part of LSU and high voltage of HVPS is cut off. The will LCD display “Front cover or Rear cover open” until the respective cover has been closed. 24VS1 Jam cover switch front cover switch 24V 24VS2 24V 24VS2 SMPS Main HVPS

LSU_5V switch connector II. Summary of Product 6. Toner Cartridge Sensing and Dot counting Toner Cartridge Sensing LSU switch is the back of the machine, it is closed if Cartridge is inserted. If user insert cartridge then LSU switch closed, LSU_5V is apply to LSU in order to +5V voltage to apply to the LD board for laser scanning. LSU_5V is goes high, CRU_DET2 signal goes low. In other words, if cartridge is inserted CRU_DET signal level goes low, if cartridge is pulled out, CRU_DET2 signal goes high. CPU detects the CRU_DET2 signal level and flags whether cartridge is in the machine. LSU_5V switch connector Dot Counting Method No toner level sensor. Instead of level sensor, software dot counting method is used. Want to view the Dot count? Print system data list, then you can see used dot count bottom of the page. Toner Low : 3,380,000,000 dots (3K cartridge) / 1,159,000,000 dots (initial cartridge) Toner Empty : 4,050,000,000 dots (3K cartridge) / 1,385,000,000 dots (initial cartridge)

II. Summary of Product 7. Useful function for troubleshooting – Tech Mode All samsung MFP has useful function for troubleshooting. Frequently used modes are <Engine Test mode>, <Tech Mode> Engine Test Mode Engine test mode is available by pressing “Menu → # → 1 → 9 → 3 → 1” If you pressing correctly, you can see “Engine Test” on the LCD. You can test some parts related printer engine like Solenoid, Engine motor, LSU, HVPS, etc… It is not difficult to use, so you just press buttons correct sequence and you could know how to use. Remember that you can test engine part just pressing “Menu → # → 1 → 9 → 3 → 1” in sequence. Tech Mode Tech mode is available by pressing “Menu → # → 1 → 9 → 3 → 4” You can test below functions by using tech mode. DRAM test Engine pattern printing Shading test F/W version check Switch test Some expanded menus are accessible for test. Like engine test mode, you could know the usage of each function. Remember only one that you can access helpful test mode by pressing “Menu → # → 1 → 9 → 3 → 4” in sequence.