Layout Tools.

Slides:



Advertisements
Similar presentations
Tessellations……… Creating Tiles that Tessellate.
Advertisements

Measuring and Layout Tools
Lines, Angles and Shapes
Hand tools. Standard Head Screw Driver Used to tighten or loosen flat head screws.
Unit 49 Intersecting Roofs
Hand Tools GE 105.
Micrometer Sizes range from 0 to 1 inch up to 12 inches.
HIP RAFTER THEORY AND SAMPLE CALCULATIONS
Safe Use of Agricultural Mechanics Hand Tools
Tool Identification Tool Identification and Use as Photographed and Prepared by Doug Best.
HIP JACK THEORY AND LAYOUT
Presentation 26: HIP RAFTER LAYOUT.
Hey! Will You Hand Me That?
Hand Tools January 27, 2009.
By:Gord Darling Construction Technology
Agriscience, Unit 7a: Investigate careers related to the field of agricultural engineering
Pencil Measuring Plumb and Level Lines. Use: Estimates Comparisons To Find: Proportions Angles Use PENCIL and THUMB to find distance.
Hip Rafters • Hip Jack Rafters • Constructing Hip Roofs
Magnet rotated by 5.9 degree Distance from entrance point to magnet right bottom corner m.
2D shapes.
Tool Identification Ag Structures.
Common Tools in Woodworking
Measurements Measurements (Fractional) Fractional measurements are called out in terms of feet and inches Example  5 feet, 3 and a half inches Same.
 Measurement started with items common to man such as a hand length, an arms length, the length of a foot or many other common items. These proved to.
Square Pyramid (cut). Cut Square Pyramid - Problem The given views show the Front Elevation and unfinished Plan of a cut square pyramid. Draw the following.
Layout Tools Prepared by Dr. Dale Carpentier Monroe Area High School Modified by Georgia Agriculture Education Curriculum Office June 2007.
Drawing & Drafting Tools. T-Square Why is the letter “T” in its name? Why is the word “square” in its name?
Shapes and Angle Rules 80 + ? = = 180.
Wood Frame Constructions Tools. Safety Glasses Eye protection that covers eyes only. Safety glasses have side shields. The California State Educational.
6.03 Tools in Agricultural Engineering Obj. 6.03: Remember tools and their safety practices related to the agricultural mechanics industry Images courtesy.

Objective 6.03 Remember tools and their safety practices related to the agricultural mechanics industry.
Objective Use agricultural mechanics hand tools properly.
Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 8 Layout Tools and Procedures.
WELDING Basic Angles Project Copyright © Texas Education Agency, All rights reserved.
 AKA Carpenters Square  Used for measuring right angles  Most common use is for stairs and rafters.
 An angle is a corner where two lines meet.  Angles are drawn with a small part of a circle in the corner.  Angles can be measured in degrees with.
Ch. 6 Geometry Lab 6-9b Tessellations Lab 6-9b Tessellations.
Safe Use of Agricultural Mechanics Hand Tools
Tool Identification. TURNING TOOLS Turn nuts, bolts, and screws.
Marking Materials Theory. Knowledge and Understanding.
Session 1: Common Hand Tools
4 Chapter Hand Tools. 4 Chapter Hand Tools Objectives Identify the most common hand tools. Select the proper hand tool for a given job. Identify the.
Jr. Hi. Shop 2017 General tools.
Prepared by Dr. Dale Carpentier Monroe Area High School
Common Unpowered Shop Tools
TOOL IDENTIFICATION.
Remember tools and their safety practices related to the agricultural mechanics industry. Objective 6.03.
Layout of Tools Tools must be laid out in definite order.
Do Now Solve each equation. x = x = 180 x + 32 = 180 x = 90
Strategies for Reading the Ruler
Hand Tools.
Rules and Other Measuring Tools
Drafting Tool Practice
Layout Tools.
Intro to Industrial Tech
Prepared by Dr. Dale Carpentier Monroe Area High School
Grade 6 Measurement Unit
7-8 Angles in Polygons Warm Up Problem of the Day Lesson Presentation
Micrometer Sizes range from 0 to 1 inch up to 12 inches.
Ag Mechanics Tools.
PARALLEL LINES CUT BY A TRANSVERSAL
2D shapes.
PARALLEL LINES CUT BY A TRANSVERSAL
Laying out the Foundation
3D shapes *.
Standard 4 Hand Tools Striking Tools Measuring and Layout Tools
Lines, Angles and Shapes
VALLEY JACK THEORY AND LAYOUT
2D shapes.
Presentation transcript:

Layout Tools

22. Chalk Line Reel

Contains chalk and string Chalk Line Reel Making straight lines Contains chalk and string

28. Combination Square

Combination Square Determining 45 and 90 degree angles

60. Framing Square

Framing Square Squaring cut corners and laying out stairs and rafters

80. Level

Level Leveling and plumbing

81. Line Level

Line Level Leveling between long distance points Use with a string

114. Plumb Bob

Vertical plumbing to locate points Plumb Bob Vertical plumbing to locate points

155. Tape Rule

Straight or curved measuring Tape Rule Straight or curved measuring

169. Try Square

Try Square 90 degree square