How will I know if I have been successful?

Slides:

Advertisements

Similar presentations

Fundamentals of Engineering

Advertisements

Isometric Drawing Part 1

Whiteboardmaths.com © 2004 All rights reserved

THINKING SKILLS Year 9 Graphics. What method of drawing am I thinking of? 1. 2 dimensional drawing? 2. Isometric Projection? 3. Orthographic Projection?

Freehand Sketching Introduction to Mechanical Engineering Fall 2004 Created by: P.M. Larochelle & J.S. Ketchel.

3 rd Angle Projection A 3 rd Angle projection is a 2D drawing of a 3D object. It shows three views the side, plan and end view. The side view is drawn.

From Isometric Drawings to Plans and Elevations

Ch 17 communicating solutions 1.Alphabet of lines- technical lines used in multi-view drawings.

Aberdeen Grammar School Isometric Views. Isometric Drawings Lengths and breadths are drawn at 30° to the horizontal. Heights are drawn vertically. All.

Sketching and Drafting Orthographically - Theory

Orthographic to Isometric

Technical Drawing Visual Communication of Technical Information

GRAPHICS EQUIPMENT. Tasks Using a piece of A3 paper make a mind map of all the piece of graphics equipment that you can think of. Write down the name.

ISOMETRICS Isometric means “equal in measure” and refers to the fact that the three receding axes are tilted at 30°. Isometric drawings are constructed.

Sketching Applications

Technical department - boclair academy Project from a Plan to draw an EE. Or project from an EE to construct a Plan. 45° Bounce Line (45° Projection Line)

Isometric Drawing - Trammel Method

Square Pyramid (cut). Cut Square Pyramid - Problem The given views show the Front Elevation and unfinished Plan of a cut square pyramid. Draw the following.

Sketching & Drawing Projects

One Point Perspective One point perspective is a 3D drawing using one vanishing point on the horizon. Objects going into the distance arrive at the same.

Chapter 4 Sketching and Orthographic Projection. 2 Links for Chapter 4 Sketching Shapes Sketching Procedures Orthographic Projection.

AutoCAD 2D_I Module 3: Freehand Pictorial Sketching.

CHAPTER 3 REVIEW What are the 7 steps of Engineering Design Process ? 1. Define the problem 2. Research the problem 3. Develop possible solutions 4. Choose.

Designing things on paper

What’s The Next Step to Beginning a Drawing……. You already Know: Measurements Tools.

Chapter 5 Sketching Applications. Introduction Sketching (i.e., freehand drawing) –Drawing without drafting equipment –Only paper, pencil, and an eraser.

Cylinders design and technology graphic communication - geometric solids getting started - equipment 30/60 o and 45 0 set square H or 2H pencil drawing.

Johnstone High School Graphic Communication Rectangular Pyramids

Orthographic Drawing. Today I will be learning to : Improve my graphic skills by learning how to draw an Orthographic Projection of a 3D object All: Will.

Chapter 3 : Communicating Ideas. Audio communication – messages that can be heard.

60 Find the start point.. Draw a construction line horizontally across the page. 60.

Isometric Views.  Lengths and breadths are drawn at 30° to the horizontal.  Heights are drawn vertically.  All sizes are drawn to their exact sizes.

Welcome to Graphics Technology Product Drawing. Subject Outline Perspective Drawing of objects Oblique Drawing Techniques Isometric Drawing Technique.

Pictorial Drawing Isometric.

Third angle orthographic projection

Orthographic to Isometric Banff Academy. Drawing the Plan and Elevations Here are three views of an object. Seeing this shape in 3D is not easy, this.

Isometric Circles.

Isometric Circle using the Ordinate Method

Draw the plan and the elevation of the cylinder, leaving 30mm between views Ø 40.

Graphic Communication

Isometric Circle using the Ordinate Method

Isometric Paper 3D Drawings © CM PowerPoint.

Isometric, orthographic, and perspective drawing…

Task 9 Describe the types of drawings that may be produced by the modelling software.

Pencils come with different hardness's

HOW TO DRAW A ROLL-OUT DEVELOPMENT LESSON 3.

TECH 104 – Technical Graphics Communication

Planometric- good technique to show 3dimensional view of a building or a room interior. Plan is drawn first and rotated through 90degrees. Vertical lines.

Technical Drawing.

Introduction to Oblique

Materials and systems Pathway Subject(s): VCE Systems Engineering

September 10, 2009 DRILL Answer the following in complete sentences:

Hexagonal Pyramid cut at an angle #2

Freehand Sketching.

Isometric Drawing.

Technical Drawing Visual Communication of Technical Information

Isometric Paper 3D Drawings © CM PowerPoint.

Missing Views Sections and of Text.

Orthogonal Drawings Orthogonal drawings are 2d drawings of 3d objects created by orthographic projection. Orthogonal: intersecting or lying at right angles.

Year 8 Term 3 Revision sheet

Technical drawings! Please update your TOC.

Technical Drawing Aims:

Chapter Seven Constructions and Scale Drawings

Projections & Technical Drawing

Multiplication Differentiated Practice Worksheet

Orthographic Projection:

1.2: Drawings, Nets, and other models

Presentation transcript:

How will I know if I have been successful? Learning Objective To explore the use of technical drawing equipment in the production of isometric line drawings. TASK Complete isometrics worksheets 1, 3, 5 and 8 (over two periods). How will I know if I have been successful? I can identify two rules in relation to isometric drawings. I can use the 30/60 set square to project lines accurately at 30°. I can use a set square and parallel motion to project vertical lines. I can produce construction lines and outlines which are clearly differentiated in line weight. I can transfer sizes from an orthographic drawing using the trammel method.