Injection mold specification

Slides:



Advertisements
Similar presentations
Part Name : Body Lower+Upper
Advertisements

YONGYI MOULD LIMITED Page1/9 kING Mould No: YY1045 Part name: P0054A2 Cavities :1X1 Material : POM Part weight: 241g Shrinkage:2.1% Part size.
Moldflow Analysis Report Page 1AG10-07, 07 JULY 2010 Cool, Flow & Warp Analysis Of Small base Part.
Moldflow Analysis Report Page 1AG10-07, 07 JULY 2010 Cool, Flow & Warp Analysis Of The Small Base Part.
Room reservations. Reserve a roomCancel your reservation Back to GGC Home Page.
Injection Molding Technology Material From Dr. Piyawit Khumphong (MTEC)
1Module 4b Casting process (continued). Module 4a2 Casting Principle of the process Structure Process modeling Defects/quality control Design and DFM.
1Module 4b Casting process (continued). Module 4a2 Casting Principle of the process Structure Process modeling Defects/quality control Design and DFM.
Part 2D Page 1 DFM. Page 2 DFM Thickness Page 3 DFM Gate HOT GATE.
Source Page US:official&tbm=isch&tbnid=Mli6kxZ3HfiCRM:&imgrefurl=
Fate proto-tool Quotation QGT-81613_V1 Project name:Fate Customer name: Nokia Total Volume: Peak Volume: 3D file release for tooling: Ramp-up schedule:
Chemical Layers of the Earth page 91. Remember when the Earth was molten? …
Путешествуй со мной и узнаешь, где я сегодня побывал.
The reading is 7.38 mm. The reading is 7.72 mm.


General Information Date OK / NG Approved by 105.6mm 17.0mm 79.2mm
Principle of the process
Injection mold specification
Injection mold specification
Injection mold specification

Firs samples Injection direction
Injection direction This area is OK , because the pin into the tube have a supporting point in this area . The injection force push the pin to the other.
Date of download: 1/2/2018 Copyright © ASME. All rights reserved.
How to Clean Xerox Printer Heads by Manually Clean.
TDRS Plastic Injection – [vehicle] [Sumitomo p/n]
Page 1. Page 2 Page 3 Page 4 Page 5 Page 6 Page 7.
Injection mold specification
Injection mold specification
I C A L I C A L DFME follow-up issue. Page. OPEN POINTS
Injection mold specification
Injection mold specification
Principle of the process
Injection mold specification
Injection mold specification
Casting process (continued)
slider qty (Each part) Client: Gadi Gate type: Model:
Injection mold specification
Model Reversion : A Client : Slider qty : 3 Model : Latte-2nd
Injection mold specification
Injection mold specification
Algebra 1B – Name: _________________________
Injection mold specification
Injection mold specification
Injection mold specification
Injection mold specification
Injection mold specification
Injection mold specification
Model Hook H Y J Revision : A Client : Slider qty : 2
Model Reversion : A Client : Slider qty : 1 Model : Latte 2nd
2019/4/26 Client: Dell Gate type : Side gate Model: DOZER Tool type:
Injection mold specification
Injection mold specification
Injection mold specification
Injection mold specification
Injection mold specification
Model A H Y J 2 Batterycover Revision : Client :
Injection mold specification
Modified at -
Injection mold specification
Thing / Person:____________________ Dates:_________________
Injection mold specification
Injection mold specification
Injection mold specification
Injection mold specification
Injection mold specification
Injection mold specification
Injection mold specification
Injection mold specification
Presentation transcript:

Injection mold specification Client FUJI Model Name FUJI-XEROX Part Name Part No. 031b097000_k001 DFM BIRD LI

Integral Corrective Action List ICAL Page OPEN POINTS SOLUTIONS/ACTION WHO 1 2 3 4 Plastic Flow Analysis Please confirm. Parting _ line 5 modify1 6 7 8 9 10 11 12 13 14 15 I C A L Integral Corrective Action List 1-Date of opening (all dates in2005) 2-Date of beginning of action 3-Date foreseen for validation 4-Date of validation (closing) DFME Follow-up issue

Plastic Flow Analysis SIDE GATE

Shade area undercut,please Parting _ line Shade area undercut,please view next page. CAVITY CORE PARTING-SURFACE

Shade section undercut.(both sides) modify1 Shade section undercut.(both sides) modify 3.8mm This surface reduce plastic 0.1mm. (both sides) 4mm