Revise No. II.

Slides:



Advertisements
Similar presentations
E4004 Surveying Computations A Two Missing Distances.
Advertisements

BASICS OF TRAVERSING H.U. MINING ENGINEERING DEPARTMENT
Similar and Congruent Figures. Similar figures have the same shape, but not the same size. They must have the same ratio of side lengths Congruent figures.
Wes Marshall, P.E. University of Connecticut March 2007
ERT252/4 GEOMATICS ENGINEERING
Geometry with TI-Nspire™ Technology
ENGINEERING SURVEYING & PHOTOGRAMMETRY CVE 314
Contour and Topo map Applications Profile View (Longitudinal Sections): Roads, Canals, Pipes,… Cross-Sectional View, Roads, Canals, Pipes, Building,…
Introduction to Traversing using distances and directions of lines between Traversing is the method of using distances and directions of lines between.
E4004 Survey Computations A
Lesson 5-4: Proportional Parts
CHAPTER 4 Coordinate Geometry and Traverse Surveying
Islamic University of Gaza Civil Engineering Department Surveying II ECIV 2332 By Belal Almassri.
UNIVERSAL COLLEGE OF ENGG. AND TECH.
Traversing Chapter 9.
Solutions to Lecture Examples Directions and Traverse.
Our eye level looking ahead is called the horizontal. Angles of Elevation and Angles of Depression angle of elevation angle of depression Horizontal (eye.
Surveying I. Lecture 10. Traversing.
Hexagonal Pyramid cut at an angle #1
BALANCING A GOVERNMENT MEANDER LINE USING STATE PLANE COORDINATES
Module C Lesson 3: Exercises Geometry with TI-Nspire ™ Technology.
Chapter 7 Coordinate Geometry 7.1 Midpoint of the Line Joining Two Points 7.2 Areas of Triangles and Quadrilaterals 7.3 Parallel and Non-Parallel Lines.
TOPIC 5 TRAVERSING MS SITI KAMARIAH MD SA’AT LECTURER
Right-Angled Trigonometry Involving 3D Example The cuboid below has length AB = 4cm, DE = 6cm and AF = 12cm. Work out the lengths of the diagonals (i)
Lesson 5-4: Proportional Parts 1 Proportional Parts Lesson 5-4.
Objective: Students will use proportional parts of triangles and divide a segment into parts. S. Calahan 2008.
Geometry Section 8.3 Similar Polygons. In very simple terms, two polygons are similar iff they have exactly the same shape.
Section 7-4 Similar Triangles.
Proportional Lengths of a Triangle
7-4: Parallel Lines and Proportional Parts Expectation: G1.1.2: Solve multi-step problems and construct proofs involving corresponding angles, alternate.
Objective After studying this section, you will be able to begin solving problems involving circles 9.2 Introduction to Circles.
FD Mathematics 1 Calculate lengths of sides and angles in right-angled triangles GCNU208A.
Warm Up Use ∆ABC for Exercises 1–3. 1. If a = 8 and b = 5, find c.
Hexagonal Pyramid cut at an angle #1
Slope and similar triangles
1.6 Basic Constructions SOL: G4 Objectives: The Student Will …
Chapter 6 TRAVERSE.
Government Engineering College, Bhavnagar Civil Engineering Third Sem
Geometry Lesson 5.4.
Warm Up Use ∆ABC for Exercises 1–3. 1. If a = 8 and b = 5, find c.
Lesson 5-4: Proportional Parts
Set up ratios: = = Fill in ratios: Solve the proportion: =
TO CONSTRUCT REGULAR POLYGONS
We have started to compute the traverse station
Lesson 5-4 Proportional Parts.
Geologic Geometry.
1-6 Midpoint Find the midpoint of: DE: DC: AB: AE: (2+5) / 2 = 3.5
The General Triangle C B A.
Angles and Directions.
Angles and Directions.
Local Attraction and Traverse
Lesson 7-4 Proportional Parts.
The General Triangle C B A.
Angles and Directions.
Angles and Directions.
ADVANCE SURVEYING.
Introduction Persons engaged in surveying are often called to determine volumes of various types of material. The most common unit of volume is cubic having.
Section II Applications of Measurements
Surveying With Construction Applications, 7th Edition
Angles and Directions.
Revise No. 1.
Angles and Determination of Direction
Introduction Persons engaged in surveying are often called to determine volumes of various types of material. The most common unit of volume is cubic having.
Horizontal and vertical angles
Revise No. 1.
Latitudes and Departures
TRAVERSING.
Lesson 5-4: Proportional Parts
Engineering Surveying Introduction to Survey Engineering
Similar and Congruent Figures. Similar figures have the same shape, but not the same size. They must have the same ratio of side lengths Congruent figures.
Presentation transcript:

Revise No. II

Q1) A highway is to be constructed to pass through points A and E of the traverse. The proposed highway grade is + 2.3 percent rising from A to E ( elevation at A = 68.95 and at B = 73.62). The ground level elevation of the cut and fill at the midpoint of formation are 70.65 and 71.72 m respectively. Compute the volume of below cut and fill sections. Elevation of the bed is 67.45. Apply for two stations long.

Q2) A five -sided closed traverse has the following angles Q2) A five -sided closed traverse has the following angles. The lengths of the sided are as follows: AB= 50.276 m BC= 26.947 m CD= 37.090 m DE= 35.292 m EA= 20.845 m The bearing of EA is N20o 20/ 20//W, and AB oriented northeasterly

a) Compute the bearings c) Compute the latitudes and departures d) the linear error of closure and the accuracy ratio. e) Compute the coordinates of the other stations if the coordinates of station A are 1000.000 N ,1000.000 E.