Module T7 Power Flow Read Module T7.

Slides:



Advertisements
Similar presentations
Announcements Be reading Chapter 6.
Advertisements

ECE 530 – Analysis Techniques for Large-Scale Electrical Systems
POWER SYSTEM ENGINEERING
TCIPG Reading Group Today’s Plan: Discuss Read and Work Ahead
ENERGY CONVERSION ONE (Course 25741) CHAPTER SIX ……SYNCHRONOUS MOTORS.
ECE 530 – Analysis Techniques for Large-Scale Electrical Systems
Power Flow Problem Formulation
4.1 Slack Variables and the Simplex Method Maximizing Objective Functions Maximize the objective function subject to: What would this look like?
EE 369 POWER SYSTEM ANALYSIS
Announcements Be reading Chapter 6, also Chapter 2.4 (Network Equations). HW 5 is 2.38, 6.9, 6.18, 6.30, 6.34, 6.38; do by October 6 but does not need.
Network Structure in Swing Mode Bifurcations u Motivation & Background –Practical Goal: examine loss of stability mechanisms associated w/ heavily loaded.
ECE 333 Renewable Energy Systems Lecture 14: Power Flow Prof. Tom Overbye Dept. of Electrical and Computer Engineering University of Illinois at Urbana-Champaign.
ECE 530 – Analysis Techniques for Large-Scale Electrical Systems Prof. Hao Zhu Dept. of Electrical and Computer Engineering University of Illinois at Urbana-Champaign.
Lecture #22 EEE 574 Dr. Dan Tylavsky Newton-Raphson Power Flow Implementation.
Per Unit Representation Load Flow Analysis Power System Stability Power Factor Improvement Ashfaq Hussain.
Technical Question Technical Question
ECE 530 – Analysis Techniques for Large-Scale Electrical Systems
Scientific Computing Partial Differential Equations Poisson Equation.
Announcements Homework #4 is due now Homework 5 is due on Oct 4
ECE 476 Power System Analysis Lecture 11: Ybus, Power Flow Prof. Tom Overbye Dept. of Electrical and Computer Engineering University of Illinois at Urbana-Champaign.
ECE 476 Power System Analysis Review 1 Prof. Tom Overbye Dept. of Electrical and Computer Engineering University of Illinois at Urbana-Champaign
Lecture 13 Newton-Raphson Power Flow Professor Tom Overbye Department of Electrical and Computer Engineering ECE 476 POWER SYSTEM ANALYSIS.
Chapter 6 Synchronous Motors
Lecture 11 Power Flow Professor Tom Overbye Special Guest Appearance by Professor Sauer! Department of Electrical and Computer Engineering ECE 476 POWER.
ECE 476 Power System Analysis Lecture 12: Power Flow Prof. Tom Overbye Dept. of Electrical and Computer Engineering University of Illinois at Urbana-Champaign.
ECE 476 Power System Analysis Lecture 14: Power Flow Prof. Tom Overbye Dept. of Electrical and Computer Engineering University of Illinois at Urbana-Champaign.
1 © A. Kwasinski, 2015 Cyber Physical Power Systems Fall 2015 Security.
Optimal Power Flow- Basic Requirements For Real Life Their Problems And Solutions.
ECE 476 Power System Analysis Lecture 13: Power Flow Prof. Tom Overbye Dept. of Electrical and Computer Engineering University of Illinois at Urbana-Champaign.
ECE 530 – Analysis Techniques for Large-Scale Electrical Systems Prof. Hao Zhu Dept. of Electrical and Computer Engineering University of Illinois at Urbana-Champaign.
ECE 530 – Analysis Techniques for Large-Scale Electrical Systems Prof. Hao Zhu Dept. of Electrical and Computer Engineering University of Illinois at Urbana-Champaign.
ELEN 3441 Fundamentals of Power Engineering Spring Lecture 10: Power-Flow studies Instructor: Dr. Gleb V. Tcheslavski Contact:
Announcements Please read Chapter 6
Announcements Please read Chapter 2.4, Chapter 6 up to 6.6
Announcements Homework 7 is 6.46, 6.49, 6.52, 11.19, 11.21, 11.27; due date is October 30 Potential spring courses: ECE 431 and ECE 398RES (Renewable Electric.
ECE 476 POWER SYSTEM ANALYSIS
ECE 476 POWER SYSTEM ANALYSIS
ECEN 460 Power System Operation and Control
ECEN 460 Power System Operation and Control
ECE 476 Power System Analysis
ECE 476 Power System Analysis
ECEN 460 Power System Operation and Control
Discussion D2.3 Chapter 2 Section 2-7
CHAPTER 2: DC Circuit Analysis and AC Circuit Analysis
ECE 476 POWER SYSTEM ANALYSIS
Load flow solutions Chapter (3).
ECEN 460 Power System Operation and Control
ECE 476 POWER SYSTEM ANALYSIS
ECE 476 POWER SYSTEM ANALYSIS
Understanding Area Balancing
ECEN 460 Power System Operation and Control
UNIT-II POWER FLOW ANALYSIS
LMP calculations Congestion evaluation
OUTAGE MODELING: PQ BUS NUMERICAL ANALYSIS & RESULTS
Load Flow Studies Eng. Edvan Moyo BEng, MEng, MBA
Some practice problems
The Power Flow Problem Scott Norr For EE 4501 April, 2017.
AC Nodal and Mesh Analysis
ECE 333 Green Electric Energy
ECEN 460 Power System Operation and Control
ECEN 460 Power System Operation and Control
ECEN 460 Power System Operation and Control
Composite Load Model with Distributed Generation (CMPLDWG)
ECE 576 POWER SYSTEM DYNAMICS AND STABILITY
ECE 576 POWER SYSTEM DYNAMICS AND STABILITY
ECE 576 Power System Dynamics and Stability
ECE 576 POWER SYSTEM DYNAMICS AND STABILITY
ECE 576 POWER SYSTEM DYNAMICS AND STABILITY
ECE 476 POWER SYSTEM ANALYSIS
Author: Italo Fernandes
Presentation transcript:

Module T7 Power Flow Read Module T7. Work problems 1, 2, 3, 7 at end of Module T7. Turn in on Tuesday, April 9.

Learning the power flow problem. 1. High-Level View Program Output & Use (project) 9. Problem solution 8. Problem formulation FOUNDATION 2. Gen React Cap Curves 5. Admittance matrix 6. PF equations for injections 7. # of equations, # of variables 3. Injections 4. Bus types

2. Gen reactive capability curve Field current limit due to field heating, enforced by overexcitation limiter on If. Q Qmax Armature current limit due to armature heating, enforced by operator control of P and If. Typical approximation used in power flow programs. P Qmin Limit due to steady-state instability (small internal voltage E gives small |E||V|Bsin), and due to stator end-region heating from induced eddy currents, enforced by underexcitation limiter (UEL).

3. Injections

First classification: Gen Load Both 4. Bus types First classification: Gen Load Both Bus type PV (usually gen) Knowns: Pinj V Unknowns: Qinj θ 2nd classification (in terms of info known at the buses). What is possible info? V θ Pinj Qinj Bus type PQ (usually load) Knowns: Pinj Qinj Unknowns: V θ

4. Bus types One more type…. This type is motivated by a power specification issue inherent to solving the power flow problem: We need to specify all MW gen and load. To do this, we need to know losses. Losses are a function of line flows. We cannot know line flows until we specify all MW gen & load. So what do we do?

4. Bus types Pull out one gen: Bus type “Swing” Knowns: V θ Unknowns: Pinj Qinj And same for reactive power. This one gen is called the swing bus, slack or reference bus.

4. Admittance matrix KCL Add bus 4 connection Gather terms Do same for other four buses and then put in matrix form Off-diagonals: negative of admittance connecting corresponding two buses. Diagonals: sum of admittances for all lines & shunts connected to corresponding bus.

4. Admittance matrix Admittance matrix (or “Y-bus”):

4. Admittance matrix Admittance matrix (or “Y-bus”):

Learning the power flow problem. 1. High-Level View Program Output & Use (project) 9. Problem solution 8. Problem formulation FOUNDATION 2. Gen React Cap Curves 5. Admittance matrix 6. PF equations for injections 7. # of equations, # of variables 3. Injections 4. Bus types

The procedure is the same in both cases. 6. PF Equations Previously, we wrote the power flow equations for the power flowing over a certain line. Now, we want to write the PF equations for the power injection. The procedure is the same in both cases. Please do understand the difference. What we computed before. What we are computing now. =Sk=SGk-SLk

6. PF Equations

6. PF Equations

6. PF Equations