Interpass temperature

Slides:

Advertisements

Similar presentations

and Statistics, 2016, Vol. 4, No. 1, 1-8. doi: /ajams-4-1-1

Advertisements

Table 4. Mechanical properties of repair and substrate concrete

Percentage of Polyethylene

Properties Test results

Table 1. Empirical MSE to estimate the CP distribution parameter λ

© The Author(s) Published by Science and Education Publishing.

Supplier Input Process Output Customer

Modulus of elasticity (GPa) Shear modulus elasticity (GPa)

Research, 2015, Vol. 3, No. 6, doi: /education

© The Author(s) Published by Science and Education Publishing.

Table 5. Properties of The Tested Soil

Fusion temperature range Clinical Applications

Table 2. Type designation of sensors in the security robot

Table 2. Parameters of the transmission line

Tensile Strength (MPa)

SON Nurse Practitioner Blackboard Community

Tensile Test after Firing

Table 1. Operating Conditions

© The Author(s) Published by Science and Education Publishing.

© The Author(s) Published by Science and Education Publishing.

© The Author(s) Published by Science and Education Publishing.

Table 6. Control sample industry distribution

Total CO2 Emissions (Electricity + Fossil Fuel)

Table 4. INVESTMENTS COST

Rating of Water Quality

% of inhibition of hydrolysis (INH)

XW9048(Xantrex inverters)

© The Author(s) Published by Science and Education Publishing.

© The Author(s) Published by Science and Education Publishing.

Number of categories that are mentioned (0% < categories < 5%)

Table 1. Geometric properties of steel tubes used

Table 2. Modal parameters estimated by Pulse Reflex®

© The Author(s) Published by Science and Education Publishing.

No. Of units of single building Rated power (W) of unit load

Table 5. Pvalues of ttests for direction a

Entrapment Efficiency (%) ± S.D.

Table 2. Air-water flow cases

Table 1. Population by University

Table 3. Main properties of the thin brass electrode

Table 5. Maximum stress, strain and deformation values

Insulation, kWh/m²/day

Table 1. Characterization Result of Leaded Petrol and Blends

Simulation Frequency(Hz)

Number of questionnaires sent out

Table 6. Pvalues of ttests for direction b

Table 1. Descriptive Statistics

Table 2. Regression statistics for direction a

Table 3. Regression statistics for direction b

Average Hardness value (HRC)

Control Valve Tag Number

S21 (at center frequency) 19 dB

Table 4. Surface roughness (outer faces)

Source of variation Degrees of freedom Sum of squares Mean square

Electrode ν (mm/s) I (A) V (V) HI (J/mm) HI average AWS E309L

© The Author(s) Published by Science and Education Publishing.

Table 2. Control Valves & Bypass Valves Process Data

Control Valve Tag Number

© The Author(s) Published by Science and Education Publishing.

Table 5. Water quality A3 well during pumping test

Table 1. K-T Diagram for Bicycle Seat

Category Quantity Secondary school 3 Student participant

No. of runs Xo X1 X2 X3 X4 Y1 Y2 Y3 Y4 Y5 Si2

© The Author(s) Published by Science and Education Publishing.

Table 3. Surface roughness (inner faces)

Table 3. Simulation results

Compressive Strength difference at 1 week (MPa)

© The Author(s) Published by Science and Education Publishing.

Table 1. Chemical Composition of Base Aluminium Alloys

Equation Tem. (°C) Specific heat Thermal conductivity

FDM (Fused Deposition Modeling)

Presentation transcript:

Interpass temperature Table 6. welding conditions and their limits Welding Parameters Units Sym Limits in code form -2 -1 +1 +2 Arc voltage Volts V 20 25 30 35 40 Wire feed rate m/min F 3 5 7 9 11 Welding speed mm/sec S 2 4 6 8 10 Interpass temperature ºC T 100 200 300 400 500 Hemaid et al. An Investigation into Effect of Butt Welding Parameters on Weldment Mechanical Properties. American Journal of Mechanical Engineering, 2016, Vol. 4, No. 3, 92-98. doi:10.12691/ajme-4-3-2 © The Author(s) 2015. Published by Science and Education Publishing.