Private & ConfidentialTakata India Private Limited Quality Dept. 1 Armature Welding Before After Feeler Gauge Normal condition Removing Feeler Blades has.

Slides:

Advertisements

Similar presentations

Measuring and Testing Instruments

Advertisements

Service Tips April COOLING SYSTEM To check and/or fill the cooling system it is necessary to remove the rear fender, the fuel tank (photo 1) and.

Waukesha Cherry-Burrell

Lock Replacement. Step 1: Cut insulation behind lock mechanism.

Clutch Replacement & Inspection Be sure to mark the Pressure Plate to Flywheel orientation. Loosen bolts in sequence 1/2 turn at a time to prevent warpage.

Cutting Machines Foldable Information. DRILL PRESS Related Terms  Center punch  Cutting Oil.

Spark Plugs Topics covered in this presentation: Spark Plug Construction Spark Plug Reach, Seating and Heat Range Spark Plug Servicing.

Head jig usage procedure RKC London Office. Set the head jig 2) Put two screws with loose condition 3) Lock the plate 4) Tighten two head jig screws 5)

Hand tools. Standard Head Screw Driver Used to tighten or loosen flat head screws.

1. Disconnect the saw from the power source.

Air Conditioning Compressors.

New Mexico FFA Agricultural Mechanics Career Development Event Engine Power.

Model 12 Intek Horizontal OHV Crankcase Disassembly and Assembly Lab #7.

Engine Measuring Vernier (Dial) Caliper Useful because it can read inside and outside measurements. Use only as a “rough” guide. Add the reading on the.

Disassemble, Assemble and Perform a Function Check on the M203

Joint fit up and alignment

Propeller Shaft survey

Assembly of a Syringe. Gather syringe and needle Select a syringe and needle. Syringe size and needle gauge will depend on the provider’s needs. Syringes.

Measurements and Precision Measuring Devices

Small Engine Parts Block Cylinder Cylinder Head.

Basic Sewing Equipment. What are notions? Items used to make an outfit such as  Buttons  Zippers  Thread  Hook and eye, etc.

Driving Procedures & Maneuvers

Cylinder, Crankshaft, and Piston Service

Learning To Drive Choosing Safety First. Choosing Safety First You have important choices to make, sometimes even before you start your car, that will.

LAP JOINT The Lap Joint is: basically one piece of wood is laid (lapped) over another piece of wood, and the two pieces fastened together in the contact.

FFA CAREER DEVELOPMENT EVENT Part 4

Introduction to Selected Welding Processes Linnert, G., Welding Metallurgy, American Welding Society, 1994.

Computer Science 313 – Advanced Programming Topics.

RABBET JOINT The Rabbet Joint is: an L-shaped cut along the end or edge of a board. a wood joint that can be built with hand or power tools. formed by.

Silver-Line SL-7 Repairs Removing the Disc Pad. Remove the Dust Tube Elbow Remove the 4 Screws & the elbow Keep the screws & elbow stored together Removing.

Small Hole Gauges & Telescoping Gauges. Small Hole Gauges These gauges are used to measure small holes that you need to know the exact measurement.

Mohammad Dedyardie Takong 08B0904. At the end of the lesson, you should be able to:  State the use of a micrometer screw gauge  Master the techniques.

Christian Löffler TE-MSC. Current design ( ) Goals for analysis Pushing unit – structural strength - pushing unit – uniformity of stress in the.

765 ½”- 2”. Modification Overview  Production of the 765 began in 1975 and is current.

1 SHEET METAL THEORY II Hand Tools and Machinery.

Holding Down and Chocking The engine must be securely fixed to the ship. For this the engine is mounted on resin or cast iron chocks and bolted to the.

Compressor Replacement – ODU

Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 23 Using Gas Welding Equipment.

LAB #10. Governor Control Arm Using a 10mm socket install the two bolts that hold the governor control arm. Finger tighten then torque to 100 “#

LAB #2 CARBURETOR REMOVAL AND REPLACEMENT. Remove Cover Using a #10 star tip and a bit driver, remove the four screws to recoil cover.

EXAMPLE : A welding robot in an automobile plant looks for a small magnetic dot to perform a spot weld. The robot has an 85% success rate for.

Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set screw throught the hole in the yellow part 2 Note: there.

DANGER UNSAFE DO NOT USE EQUIPMENT NEEDS REPAIRS UNSAFE DO NOT USE EQUIPMENT NEEDS REPAIRS LOCKED OUT BY: Name: _______________________ Dept: ________________________.

The 5 Phases Welcome Assessment Presentation Objection Closing.

1 Engine Mechanical Labs R. Bortignon. 2 Repair Information – essential! locate model number!

EXERCISE 1.4 MICROMETER SCREW GAUGE. D mm C mm B mm A mm    Q1. The diagram shows a micrometer screw gauge. Which reading is.

Oxyacetylene Start Up/Shut Down Procedure Prepared by Dr. Dale Carpentier and Mr. Barry Brazelton Monroe Area High School Modified by Georgia Agriculture.

Marking Materials Theory. Knowledge and Understanding.

CH 6.4 Measuring Tools.

Tapping/Threading Tools

Oxyacetylene Start Up/Shut Down Procedure

KP199 Cannibalizing Process (To avoid Component track Open)

Website: Find Latest Tender, Latest Tenders in India Mobile: Website:

Module 3 Domestic Heating/MMA Welding

T400 Motor Replacement.

FIGURE 7-2 A plastic rule that has both inches and centimeters

Factorizing expressions

KNOCK OUT DIAMOND KNOCK-OUT DIAMOND -REMOVAL.

Service Tips April 2005.

Bream Plus lid closing problem

DC4A (LF) ½”-2”.

Modify a Worksheet Updated July 29, 2010.

Remove addition/subtraction

Guides & Links Basic Mechanical Function

Removable and permanent connections

Hair Removal Methods: What's Effective and What's Not.

Measuring Systems and Tools

Hand and Power Tools This presentation will explore:

Presentation transcript:

Private & ConfidentialTakata India Private Limited Quality Dept. 1 Armature Welding Before After Feeler Gauge Normal condition Removing Feeler Blades has Easily, so Checking is Problem. I have provide a one Spot Welding In Locking Screw Area, so Not Remove Feeler Blades Easily.