Power Tools and Shop Equipment

Slides:



Advertisements
Similar presentations
USING THE OXYACETYLENE CUTTING TORCH
Advertisements

Using Gas Welding Equipment
UNIT: Oxy-Fuel Welding, Brazing, Cutting and Heating LESSON: OXY-ACETYLENE EQUIPMENT SAFETY Standard B7.2 – Know how to properly set up, adjust, shut down.
Harkness career center
Cutting and Threading Steel Pipe
Oxyacetylene Torches.
1926 Subpart J Establishes the requirements for welding and cutting in the construction industry Establishes requirements for equipment, fire protection,
Machine Shop Hazards, Machine Tool Safety
Unit: Oxy-Acetylene; Welding, Brazing, Cutting & Heating
Oxy Fuel Cutting Systems Basic Setup & Use
Technology Education Dept. Bellwood-Antis High School Mr. Crowell Mr. Mackereth.
HOW TO LIGHT AND TURN OFF THE OXY-ACETYLENE TORCH
OXY-ACETYLENE TORCHES Protect your head and eyes by wearing proper welding goggles or face shields equipped with a minimum shade 5 lens. Protect your.
Oxy-fuel Welding and Cutting By: John Templeton
1 REFRIGERATION FUNDAMENTALS HVAC/R. 2 SOLDERING & BRAZING When and why; –When an A/C or refrigeration system is entered, it must be properly sealed –Although.
OBJECTIVES After studying Chapter 5, the reader will be able to:
Flexible Manufacturing Welding Safety Copyright © Texas Education Agency, All rights reserved. 1.
Andrew Brock. Terms  The burning qualities of gases are used in Ag Mechanics to heat, weld and cut metals  Weld- to join by fusion  Fusion- melting.
Terms and Definitions Base Metal: Metal to be welded Fusion Welding: process that joins metals by heating them to a melting point and allowing them to.
Metal Cutting Processes Flexible Manufacturing
POWER TOOLS AND SHOP EQUIPMENT
© Goodheart-Willcox Co., Inc. Permission granted to reproduce for educational use only Publisher The Goodheart-Willcox Co., Inc. Tinley Park, Illinois.
4 Chapter Power Tools and Equipment.
Gas Welding.
Module 1 : Lesson 1: Working safety in the shop
Oxygen Acetylene Equipment Oxygen = Green Acetylene = Red.
Oxyacetylene Cutting O.A.C. Pattern Cutter Cutting Torch.
1 HVACR316 - Piping Fundamentals of Refrigeration Soldering and Brazing Fundamentals of Refrigeration Soldering and Brazing.
CUTTING -Don’t fire pilot arc into air -Start cutting from edge of workpiece -Sparks should come out from bottom of piece. If they spray on the top,
CHECK VALVES Are installed to prevent the reverse flow of gases that would result in a combustible mixture in the welding hose, check valves are mounted.
Safety Test. 1. Safety Fill in both blanks… If lifting is required, lift with your ___, not the _____. Get some help for heavy and bulky objects…
Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 23 Using Gas Welding Equipment.
Metal Design Safety SAFETY FIRST!. Safety Goggles Always wear when using the following machinery Buffing wheels Soldering Pickle pot Drill press Advance.
© Goodheart-Willcox Co., Inc.. Power Tools and Equipment  Power tools  tools driven by compressed air, electricity, or pressurized liquid  Shop equipment.
Oxy-Fuel Welding. What is Oxy-Fuel Welding? Process the fuses metal together Does not require electricity Uses a torch and filler rod Similar equipment.
Automotive Engines: Theory and Servicing, 7/e By James D. Halderman Copyright © 2011, 2009, 2005, 2001, 1997 Pearson Education, Inc., Upper Saddle River,
© Goodheart-Willcox Co., Inc.. Compressed Air  Air compressor provides compressed air  Turns on and off automatically to maintain a preset pressure.
The Welding/Cutting Torch Objective 25.0 Demonstrate proper procedures for oxyacetylene processes.
Welding Safety Test.
ALL ABOUT PNEUMATIC TOOLS. The pneumatic tools normally used for heavy equipment extrications are the percussive type tools, such as the rivet hammer,
Oxy Fuel Systems Basic Setup & Use Mr. Lacey Livingston High school.
9 HAND TOOLS.
CH 6.5 Electric Power Tools.
Oxyacetylene Fusion Welding Safety Review
BASIC GAS METAL ARC WELDING
Automotive Engines Theory and Servicing
Metal Shop Safety By: Jaryn and Rhiannon.
Using Gas Welding Equipment
Oxyacetylene Welding Equipment
Oxyfuel cutting NCCER Welding Unit 2.
Safety Test.
CH 6.6 Air Powered Tools.
Oxy-Acetylene Torches
Flexible Manufacturing
Unit 22 Ag mechanics Using gas equipment.
Safety O.H.S..
Safety Test.
Compressed Cylinder Safety
Cutting Tip Chart 7. Refer to a cutting tip selection chart for correct cutting tip, regulator pressures, and travel speed.
Chapter 13 Offhand Grinding. Chapter 13 Offhand Grinding.
THE OXYACETYLENE TORCH
Oxygen/ Fuel Cutting and Welding
Safety Stuff.
1 Safety in the Small Gas Engine Shop. 1 Safety in the Small Gas Engine Shop.
4 Chapter Power Tools and Equipment. 4 Chapter Power Tools and Equipment.
General Shop Safety Thinking Safe… Prevents Injury!
Oxygen Acetylene Cutting Torch
Automotive Technology Principles, Diagnosis, and Service
Chapter 4 Power Tools and Equipment.
Presentation transcript:

Power Tools and Shop Equipment 10 Power Tools and Shop Equipment Introduction to Automotive Service James Halderman Darrell Deeter

FIGURE 10. 1 A typical shop compressor FIGURE 10.1 A typical shop compressor. It is usually placed out of the way, yet accessible to provide for maintenance to the unit.

FIGURE 10. 2 Always use an air nozzle that is OSHA approved FIGURE 10.2 Always use an air nozzle that is OSHA approved. The openings in the side are used to allow air to escape if the nozzle tip were to become clogged.

FIGURE 10.3 A typical 1/2 in. drive impact wrench.

FIGURE 10.4 This impact wrench features a variable torque setting using a rotary knob. The direction of rotation can be changed by pressing the button at the bottom.

FIGURE 10.5 A typical battery-powered 3/8 in. drive impact wrench.

FIGURE 10. 6 A black impact socket FIGURE 10.6 A black impact socket. Always use impact-type sockets whenever using an impact wrench to avoid the possibility of shattering the socket, which can cause personal injury.

FIGURE 10.7 An air ratchet is a very useful tool that allows fast removal and installation of fasteners, especially in areas that are difficult to reach or do not have room enough to move a hand ratchet wrench.

FIGURE 10.8 This typical die grinder surface preparation kit includes the air-operated die grinder, as well as a variety of sanding discs for smoothing surfaces or removing rust.

FIGURE 10.9 A fluorescent trouble light operates cooler and is safer to use in the shop because it is protected against accidental breakage where gasoline or other flammable liquids would happen to come in contact with the light.

FIGURE 10.10 A typical pedestal grinder with a wire wheel on the left side and a stone wheel on the right side. Even though this machine is equipped with guards, safety glasses or a face shield should always be worn when using a grinder or wire wheel.

FIGURE 10.11 A typical vise mounted to a workbench.

FIGURE 10.12 A hydraulic press is usually used to press bearings on and off on rear axles and transmissions.

FIGURE 10.13 A typical portable crane used to lift and move heavy assemblies, such as engines and transmissions.

FIGURE 10. 14 Two engines on engine stands FIGURE 10.14 Two engines on engine stands. The plastic bags help keep dirt from getting onto the engines.

FIGURE 10.15 An engine stand that attaches to the engine from the sides rather than the end.

1 SETUP AND LIGHTING A TORCH Inspect the cart and make sure the tanks are chained properly before moving it to the work location. 1

2 SETUP AND LIGHTING A TORCH Start by attaching the appropriate work tip to the torch handle. The fitting should only be tightened hand tight. Make sure the valves on the torch handle are closed at this time. 2

3 SETUP AND LIGHTING A TORCH Each tank has a regulator assembly with two gauges. The high pressure gauge shows tank pressure, and the low pressure gauge indicates working pressure. 3

4 SETUP AND LIGHTING A TORCH Open the oxygen tank valve fully open, and open the acetylene tank valve 1/2 turn.

5 SETUP AND LIGHTING A TORCH Open the oxygen valve on the torch handle 1/4 turn in preparation for adjusting oxygen gas pressure.

6 SETUP AND LIGHTING A TORCH Turn the oxygen regulator valve clockwise and adjust oxygen gas pressure to 20 PSI. Close the oxygen valve on the torch handle. 6

7 SETUP AND LIGHTING A TORCH Open the acetylene valve on the torch handle 1/4 turn and adjust acetylene gas pressure to 7 PSI. Close the acetylene valve on the torch handle. 7

8 SETUP AND LIGHTING A TORCH Open the oxygen valve on the torch handle 1/4 turn and use an appropriate size tip cleaner to clean the tip orifice. Finish by closing the oxygen valve. 8

9 SETUP AND LIGHTING A TORCH Put on leather gloves and open the acetylene valve on the torch handle 1/4 turn. Use a flint striker to ignite the acetylene gas exiting the torch tip. 9

10 SETUP AND LIGHTING A TORCH Adjust the acetylene valve until the base of the flame just touches the torch tip. Slowly open the oxygen valve on the torch handle and adjust for a neutral flame (blue cone is well-defined).

11 SETUP AND LIGHTING A TORCH Once work is complete, extinguish the flame by quickly closing the acetylene valve on the torch handle. Be prepared to hear a loud “pop” when the flame goes out. Close the oxygen valve on the torch handle.

12 SETUP AND LIGHTING A TORCH Close the valves on both tanks and turn the regulator handles CCW until they no longer contact the internal springs. Open the gas valves briefly on the torch handle to release gas pressure from the hoses. Close the gas valves on the torch handle and put away the torch assembly.

HEATING METAL Heating attachments include ordinary heating tips, middle and right and a “rosebud” (left). Ordinary heating tips work fine for most purposes, but occasionally the rosebud is utilized when a great deal of heat is needed. 1

HEATING METAL Note that while acetylene tank pressures are relatively low, the oxygen tank can be filled to over 2,000 PSI. This can represent a serious hazard if precautions are not taken. Be absolutely certain that the tanks are chained properly to the cart before attempting to move it! 2

HEATING METAL Any time heating or cutting operations are being performed, be sure that any flammables have been removed from the immediate area. A fire blanket may be placed over floor drains or other objects to prevent fires. A fire extinguisher should be on hand in case of an emergency. 3

HEATING METAL Be sure to wear appropriate personal protective equipment during heating and cutting operations. 4

HEATING METAL Note that heating operations should be performed over steel or firebrick. Never heat or cut steel close to concrete, as it could cause the concrete to explode. 5

HEATING METAL When heating steel, move the torch in a circular pattern to prevent melting of the metal. Don’t hold the torch too close to the work as this will cause a “snapping” or “backfire” that can extinguish the flame. 6

CUTTING METAL Affix the cutting attachment to the torch handle. Note that the cutting attachment has a cutting handle and a separate oxygen valve. 1

CUTTING METAL Fully open the oxygen valve on the torch handle. Oxygen flow will now be controlled with the valve on the cutting attachment. 2

CUTTING METAL Oxygen gas pressure should be adjusted to 30 PSI whenever using the cutting attachment. Acetylene pressure is kept at 7 PSI. 3

CUTTING METAL Open the acetylene valve on the torch handle 1/4 turn and light the torch. Adjust the flame until its base just touches the cutting tip. Slowly open the oxygen valve on the cutting attachment and adjust the flame until the blue cone is well-defined. 4

CUTTING METAL Direct the flame onto a thin spot or sharp edge of the metal to be cut. This will build the heat quicker in order to get the cut started. 5

CUTTING METAL When the metal glows red, depress the cutting handle and move the torch to advance the cut. You will need to move the torch faster when cutting thinner pieces of steel. On thicker pieces, point the cutting tip into the direction of the cut. 6