The CO2 Dragster TIJ 101 Upon finishing your brainstorming and Final Drawing (with dimensions and ruled lines) The following steps with be taken for fabrication.

Slides:

Advertisements

Similar presentations

Objective Use agricultural mechanics tools properly and safely.

Advertisements

Mr. Kassel Technology Foundations Technology Education

CO2 Dragster Cars

Manufacturing. Frame I manufactured large portions of the frame at home as I felt this was easier done at home an I felt the lab times could be better.

Table of Contents Unit 1- Understand the Problem Unit 2- Gather Information Unit 3-Develop Solutions Unit 4-Implement a Solution Unit 5-Test and Evaluate.

Introduction It is expected your completed plan will require you to refer to applicable specifications, refer to reference documents and follow established.

Co2 Car Preparation.. Use scissors to cut out your Co2 car.

Primary Challenge.

Research I researched a lot of CO2 dragster cars online. There are a lot of opinions out there on what works best. Some people insist that light, smaller.

Spiral Stairs Assembly Instruction By Laser Dollhouse Designs

Building a Wooden Planter Box. The Most Important Part of any Project is the Planning Determine what type of wood to use for the box (pine, cedar, cypress,

The Little Nikki Assembly Instruction By Laser Dollhouse Designs.

Repairing and Reconditioning Tools Tool Fitting. Objectives: 1)Identify and remove rust from tools in the lab with 100% accuracy 2)Demonstrate the application.

TOOL: Radial Arm Saw NEXT STEP: Radial Arm Saw RESULTS: Finish Top Apron Pieces at 9” L x 4” W x ¾ “ Th PROJECT Square Plant Stand PART Top Apron # NEEDED.

Overall Project Objectives You will develop your marking out skills. You will develop your ability to read and follow working drawings Master the use.

CO2 Dragster Project Julia Rodriguez. UNDERSTAND The cars are powered by the CO2 cartridge being punctured. The cars will race on a 20 meter track along.

PLAN #PartProcessTools and equipmentQuality controlSafety *Aprons must be worn is ALL stages of manufacture Tim e 1 MDF base Mark out on MDF piece Pencil,

CO2 Cars Project #2 Land Transportation.

Jack Mangan and Chandler Owen

Planning Manufacture TaskEquipmentQC/QA Mark out the shape of the speaker front and back Tri square, pencil, ruler, tape measure.

Intro to Power Tools Ag Mech I Class Notes. Objectives AM15.01 Explain how power tools are used in agricultural mechanics. AM15.02 Know and demonstrate.

Rut ‘n’ Strut Game Calls How I turn a Pot Call. Select wood that you want to use to turn Pot Calls out of, Rip it 4” wide and then Crosscut into 4” X.

UNIT PROJECT #3 INTRODUCTION Day 2 Day 3 Day 4 Day 5 Day 6 Day 7 Day 8.

Proper Use of Agricultural Mechanics Power Tools

Agriscience Toolbox Plan of Procedure 1. Table Saw (equipment) Rip the bottom of the toolbox to a width of 10 inches.

F. 1 Design and Technology

Module-6 Drilling.

Mr. Sexton Engineering Technology

Production Decisions Chapter 6 Mr. Higgins. Objectives Identify the need for a plan of procedure Identify the need for a plan of procedure List the steps.

First Project: A Sign Principles of Manufacturing 1 Copyright © Texas Education Agency, All rights reserved.

Drill What is the purpose of practicing?

Step one: Page Border and title block. Border will be ¼” from the edge of the paper. Drawing will be done in landscape format. Title block will be 1”

CO2 Car Specifications Rules and Regulations

Tool Use & Safety Tool Types Proper Tool Usage Safety.

Principles of Manufacturing Copyright © Texas Education Agency, All rights reserved 1.

University of Nebraska–Lincoln Know how. Know now.

Proposed Agriculture Courses Board of Education October 6, 2015.

Making a Excalibur letter opener Prepared for Ken Jeberg By Ken Jeberg Trades Technology Teacher Education.

Overall Project Objectives You will develop your marking out skills. You will develop your ability to read and follow working drawings Master the use.

Nathanael O’Hara. IDEAS I Researched Games Tables I liked these designs in part I decided to mesh the designs into something I liked and also could work.

ELECTRIC VEHICLE PROJECT CAR BUILDING PROCEDURES BY: PIERRE PEASHA CENTENNIAL HIGH SCHOOL BAKERSFIELD, CA.

"Cryptex Style" Maze Coin Puzzle

KS4 Graphic Products.  Describe the process of block modelling of MDF & Styrofoam and rapid prototyping using stereolithography (SLA) and 3D printing.

TIJ101 Tech Exam Review main types of technology career? Motive Power Service Construction Industrial.

Machine Safety Rules. Miter Saw Instructor must be present when you are using this machine. Keep wood flat and against fence Hold down wood Do not remove.

Bandsaw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the.

CO 2 Dragsters Colts Neck High School Innovation & Design (HONORS)

CO2 Racing AMHS Year One. Performance: Time: s Rank: 1st.

The Process of Making The Best CO2 Machine! Agricultural Mechanics / Woodshop Mr. Weaver The Process of Making The Best.

Making Finger Joints.

General & Machine Safety Notes

Board Replacement for Floating Floors

Proper Use of Agricultural Mechanics Power Tools

Drill Press Safety.

Question/Quality check

Brier Terrace Middle School Mr. Sullivan

Using the Chromatic scale

BC Technology Education Association

Relief Woodcarving Art Intermediate.

Band Saw Safety Rules.

RACE CARS (Compressed Air Cars)

Make a Two Note Wooden Whistle 1: Cut a piece of wood 20mm thick x 30mm wide to a length of 100mm. Use a back saw and a miter box to make the cut. 2: Use.

Proper Hand Tool Use and Safety

BC Technology Education Association

Segmented Turning Basics - part 2

Starter of the day Pick up your grades from hanging file if you did not last time. What is your grade in this class? Why is your grade this way? If it.

BC Technology Education Association

Presentation transcript:

The CO2 Dragster TIJ 101 Upon finishing your brainstorming and Final Drawing (with dimensions and ruled lines) The following steps with be taken for fabrication and completion of your Dragster

Step 1 Get Block of wood

Step 2 Layout hole location for the CO2 Cartridge. Make sure you mark the bottom.

Follow the proper safety and set-up procedures for the drill press and drill the CO2 hole.

Layout and drill holes for the axels.

Layout dragster design on the wood

Cut the dragster leaving the line. Make relief cuts if needed. Make sure the bandsaw guard in not more than 10 mm above your work.

Shape the car to the design required. Rasp or 80 grit paper.

Sand the car using 120 grit paper. Sand with the grain of the wood

Sand the car with 220 grit paper.

Decide on the type of finish Paint or stain

Prime the car. Primer seals the wood and gives a better finish.

Light sand 220 grit

Paint the car. Less is better. Spray painting must be done at home.

Get eyelets and install them Get eyelets and install them. Make sure they do not line up with the axels. Also, check and make sure they do not rub on the floor.

Do ramp test. This checks how straight your car goes.

Ready for racing.