Bob Cloutier, for SSPC Technical Services Dept.

Slides:



Advertisements
Similar presentations
Removing Coatings and Cleaning Masonry Substrates
Advertisements

Agenda Introduction Advisory Circular Changes Consultant Selection Procedures Contract Format and Provisions Methods of Contracting and Allowable Costs.
WP4 – Task 4.4 LCA Activities
Ahead in abrasives. Introduction Eurogrit BV Eurogrit’s head-office in Papendrecht The Netherlands.
Steps to a More Effective UHP Waterjetting Operation Presented by: Rick Dupuy UHP Projects, Inc.
Waterjetting—New Standards for Assessing End Condition Cleanliness
Steps to a More Effective Power Tool Cleaning Presented by: Earl Bowry, Jotun Paints, Inc.
Update on SSPC Standards Useful to the Steel Fabrication Industry
William D. Corbett KTA-Tator, Inc.
Concrete Cleanliness Inspections – Extent of Paint Removal For repaints, verify adequacy of paint removal Definitions for the amount of paint or stain.
Florida Department of Environmental Protection Looking Ahead.
William D. Corbett, KTA-Tator, Inc. Chair – SSPC Committee C.3.2 on
Standards, Training, and Certification in the Oil and Gas Industry Presented by: Ernst Toussaint, TransCanada.
STAAR A STAAR Alternate 2 Changes to Mathematics Assessments Changes to Writing Assessments Students Receiving Instruction Above Grade Level Standardized.
NPSS AdCom 15 November 2014 Seattle President’s Report Janet Barth 1.
Technical Advisory Committee COPS Update to TAC Debbie McKeever COPs Chair 2010.
Calendar Highlights – STAAR Alternate 2 testing window has been expanded. – Administration date for STAAR grades 5 and 8 mathematics has shifted. – Report.
Busting The Myths of Wet Abrasive Blasting
GOAL SETTING CONFERENCES BRIDGEPORT, CT SEPTEMBER 2-3,
William D. Corbett KTA-Tator, Inc.
Applying Coatings over Flash Rust in a Marine Environment
RC14001 ® Update GPCA Responsible Care Committee September 23, 2013.
New Advanced Higher Subject Implementation Events
Implementing the New Reliability Standards Status of Draft Cyber Security Standards CIP through CIP Larry Bugh ECAR Standard Drafting Team.
IRP, Inc. Update 2012 IFTA Annual Business Meeting Grand Rapids, Michigan.
Academic Research Enhancement Award (AREA) Program Erica Brown, PhD Director, NIH AREA Program National Institutes of Health 1.
Presented by: David Beamish DeFelsko Corporation
Standards Certification Education & Training Publishing Conferences & Exhibits 1Copyright © 2006 ISA ISA-SP99: Security for Industrial Automation and Control.
1 Control Room Habitability Program James A. Carlson, Omaha Public Power District, Author Deep Ghosh, Southern Nuclear Operating Greg Holbrooks, PE, Duke.
Use of Field-Applied Fluoropolymer Coatings for Maintenance and Restoration Applications D+D Webinar Bob Parker (AGCCA) June 29, 2011.
Application of Thermal Spray
DICOM to ISO-DICOM Report to joint ISO TC215/WG2 – DICOM WG10 meeting January 24, 2004, San Diego.
Paint Removal from CMU and Brick Kenneth A. Trimber KTA-Tator, Inc.
Standards, Training, and Certification in the Wastewater Industry Presented by: Bob Murphy, Sherwin Williams.
Standards, Training, and Certifications in the Marine Coatings Industry Presented by: Earl Bowry.
IRP Update IFTA 2006 Annual Business Meeting Las Vegas, NV Dave Saddler Presented by: Dave Saddler Executive Director IRP, Inc.
COLORADO DEPARTMENT OF PUBLIC HEALTH AND ENVIRONMENT WATER QUALITY CONTROL DIVISION Regulation 100 Update September 2011.
ELIXIR SAB Feedback December 2014.
Learning Objectives ˗ Specification Components ˗ Consideration of Variables.
Internal and external control in an automated environment
CLEAN UP & INSPECTION.
Inspection of Thermal Spray Coatings
Commercial Operations Sub-Committee Update to TAC
Prepared by Rand E Winters, Jr. ASR Senior Auditor October 2014
SURFACE PREPARATION BY BLAST-CLEANING
NACE SPECIFICATION White Metal Blast Cleaning
Structure of the Code – Phases 1 and 2
Specification Components Consideration of Variables
Larry Bugh ECAR Standard Drafting Team Chair January 2005
Larry Bugh ECAR Standard Drafting Team Chair January 2005
The Importance of Specification Writing
IAASB-IESBA Coordination
Department of Environmental Quality
Physical Education Academic Content Standards
NERC Reliability Standards Development Plan
Larry Bugh ECAR Standard Drafting Team Chair June 1, 2005
Proposed TGv Selection Process
Audit Evidence Bob Dohrer, Technology Working Group Chair and Audit Evidence Working Group Chair IAASB CAG Meeting, New York Agenda Item D March 5, 2019.
Specification on float equipment
John Kern SSPC Technical Services Dept.
NERC Reliability Standards Development Plan
2nd Edition: 2019 Winter Standards Meeting
Review plan of the nature reporting – update 6
Proposed TGv Selection Process
New Commissioners’ Meeting IFTA Amendments
Attorney’ Meeting IFTA Amendments
William Corbett, Carly McGee and Jason Coley KTA-Tator, Inc.
NSRP Joint Project SP&C and WD Panels Robert Cloutier
SSRAC 2019 Robert Cloutier September 10 – 12, 2019
Technology Bob Dohrer, Technology Working Group Chair
Presentation transcript:

Bob Cloutier, for SSPC Technical Services Dept. SSPC Standards Update September 2019 NSRP SP&C Panel, September 10-12, 2019 Quonset Point, RI Bob Cloutier, for SSPC Technical Services Dept.

Topics Ongoing Revision Projects 2019 Update SSPC-SP 11, Power Tool Cleaning to Bare Metal; and SSPC-SP 15, Commercial Grade Power Tool Cleaning SSPC-PA 17, Procedure for Determining Conformance to Steel Profile/Surface/Roughness/Peak Count Requirements  Proposed revisions to SSPC/NACE Joint Dry Blast Cleaning Standards QP 2 Standard Revision (QP 1 revision is complete)

Topics (cont’d.) New Projects SSPC-SP 17 Standard for Thorough Blast Cleaning of Non-Ferrous Metals (SSPC Board has approved) Possible technology update to non-profiling surface preparation techniques (plasma blast, laser ablation, possibly dry ice) that do not generate secondary waste stream Board of Governors has approved Thorough Blast Cleaning of

2019 Revisions – SP 11 and 15 No significant change in cleanliness requirements Proposed table for selection of tool types for various uses, e.g. Rust removal Removal of single coating layer Removal of all coating layers Creation of anchor profile Feathering edges

Proposed Revisions SP 11 and 15 Addition of a tool selection table is proposed Table will describe various existing conditions and the appropriate tools to use for best results on each condition Proposal for new cleanliness standard needs more “grassroots support” from users and contractors to be developed as a separate standard

Power Tool Selection Table Still a “work in progress” Types of tools (still in discussion) include Grinding wheels Coated abrasive discs/belts/flaps Nonwoven abrasive flap Nonmetallic brush Metallic brush Rotary flapper Cutter bundle Bristle impact Needle gun

SP 11 on Ship Deck

Revision PA 17 (Compliance to Profile Requirements) New appendix that describes techniques for measuring profile on severely pitted substrates Take readings on non-pitted area of substrate if available Create companion coupon of non-pitted steel to evaluate profile created by the abrasive Definitions are being revised to reflect revisions in ASTM D4417 - waiting for publication of revised D4417 before continuing work ASTM had to reballot D4417 due to internal issue with previous ballots. ASTM ballot due September 9. So PA 17 revision is still “on hold.”

Heavily Pitted Steel

2019 Revision of SSPC-PA 2 Revision issued January 2019 Added nonmandatory appendix describing use of scanning probe technology to acquire readings

Scanning Probe

PA 2 Appendix 10 Highlights Scanning Batch Measurement – mean of no fewer than 12 and up to 24 DFT readings w/o lifting probe from coated surface Readings taken within 645 m2 (~100 in2) segment of coated area Scanning Area Measurement – sample mean of 5 scanning batch measurements obtained over each 10 m2 (~100 ft2)

Large box represents 100 ft2 area (scanning area) Smaller boxes represent 100 in2 areas (scanning batch)

Revisions to Joint Dry Blast Standards SSPC and NACE Committees voting on “template” language revisions that affect all five dry blast standards SSPC-SP 10/NACE No. 2 has been chosen to provide the “template” Most changes proposed to reflect parallel language in joint WAB standards issued in 2018

Revisions to Dry Blast Standards (cont’d.) Propose to add Info on removal of pack, stratified, rust scale as in 2018 revisions of SP 2 and SP 3 (include instructions for methods and extent of removal in project spec) Nonmandatory commentary sections on nonvisible contaminants, definition of staining, example of specification statement No plan to change the existing cleanliness definitions First draft ballot to SSPC and NACE completed (there was one negative), joint SSPC-NACE task group is reviewing comments.

SSPC-SP 17, Thorough Blast Cleaning of Non-Ferrous Metals Cleaning of previously coated non-ferrous alloys (copper, aluminum), stainless steel for subsequent coating application Organization similar to dry blast cleaning standards for steel Non-mandatory appendices contain supplementary info on selection of abrasives, blast pressures, chemical cleaning, profile, etc. Should be available on SSPC Marketplace by October 1.

Possible Non-Profiling SP Technology Update Include use of laser ablation, plasma blasting, and dry ice blasting Conference call held September 5 to draft proposal After all interested parties approve proposal (concept) it is sent to Standards Review Committee If SRC approves proposal, SSPC will canvass for consensus review body and task group will work on preliminary draft

QP 1 2019 Revision Revised standard issued January 7, 2019 PCCP Advisory Committee is working on revising Audit Checklist to reflect revisions No audits to the 2019 requirements are planned until 2020 Clarifications to subcontracting requirements and requirements for EH&S manager training and education are the principal changes

QP 2 Revision Board of Governors ballot for publication approval due September 15 Revisions to Audit Checklist will start after standard is approved and require approval by PCCP Advisory Committee

Questions? THANK YOU!