Potential of a Transcritical Regenerative Series Two Stage Organic Rankine Cycle for Dual Source Waste Heat Recovery Anandu Surendran Satyanarayanan Seshadri.

Slides:



Advertisements
Similar presentations
OFF DESIGN PERFORMANCE PREDICTION OF STEAM TURBINES
Advertisements

Department of Mechanical Engineering ME 322 – Mechanical Engineering Thermodynamics Review for Exam 3.
A novel IGCC system with steam injected H2/O2 cycle and CO2 recovery P M V Subbarao Professor Mechanical Engineering Department Low Quality Fuel but High.
Problem Ideal and Actual Gas-Turbine (Brayton) Cycles 9–73
Refrigeration Cycles Chapter 11.
İsmail ALTIN, PhD Assistant Professor Karadeniz Technical University Faculty of Marine Sciences Department of Naval Architecture and Marine Engineering.
Vapor and Combined Power Cycles
9 CHAPTER Vapor and Combined Power Cycles.
Chapter 1 VAPOR AND COMBINED POWER CYCLES
ENERGY CONVERSION ES 832a Eric Savory Lecture 11 – A small-scale power plant worked example Department of Mechanical.
SIZING MODELS AND PERFORMANCE ANALYSIS OF WASTE HEAT RECOVERY ORGANIC RANKINE CYCLES FOR HEAVY DUTY TRUCKS (HDT) Ludovic GUILLAUME 1 & co-workers : A.
“Energy Efficiency Guide for Industry in Asia”
Vapor and Combined Power Cycles
GAS TURBINE POWER PLANTS
Shaft Power Cycles Ideal cycles Assumptions:
Lec 23: Brayton cycle regeneration, Rankine cycle
EGR 334 Thermodynamics Chapter 9: Sections 7-8
Cogeneration.
Power Generation Cycles Vapor Power Generation The Rankine Cycle
1 Operation of heat pump cycles Jørgen Bauck Jensen & Sigurd Skogestad Department of Chemical Engineering Norwegian University of Science and Technology.
Power Generation Using Multi Component Working Fluids P M V Subbarao Professor Mechanical Engineering Department Indian Institute of Technology Delhi Synthesis.
Thermodynamics II Chapter 1 VAPOR POWER CYCLES
Vapor and Combined Power Cycles (2)
Unit 4 Exercise – Gas Vapour and Combined Power Cycle
Lesson 8 SECOND LAW OF THERMODYNAMICS
Plant Utility System (TKK-2210) 14/15 Semester 4 Instructor: Rama Oktavian Office Hr.: M-F
A Vapor Power Cycle Boiler T Turbine Compressor (pump) Heat exchanger
GAS TURBINE POWER PLANT
1 ChemE 260 Improvements and Non-Ideal Behavior in the Rankine Cycle May 20, 2005 Dr. William Baratuci Senior Lecturer Chemical Engineering Department.
Analysis of Rankine Cycle with FWHs P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Engineering solution to Pure Thoughts..…..
Chapter 10 Vapor and Combined Power Cycles Study Guide in PowerPoint to accompany Thermodynamics: An Engineering Approach, 7th edition by Yunus.
Page 1 Petten 27 – Feb ALFRED and ELFR Secondary System and Plant Layout.
7th International Scientific Conference on “Energy and Climate Change”
The Rankine Cycle: An Alternate Ideal Thermodynamic Model P M V Subbarao Professor Mechanical Engineering Department IIT Delhi A Feasible Mathematical.
THERMODYNAMICS CYCLES RELATED TO POWER PLANTS
1 Chapter 5 Mass and Energy Analysis of Control Volumes.
First Law of Thermodynamics applied to Flow processes
Chapter 10 VAPOR AND COMBINED POWER CYCLES
Chapter 10 VAPOR AND COMBINED POWER CYCLES
Vapor ,Gas and Combined Power Cycles
L. Guillaumea, A. Legrosa, V. Lemorta
Objectives Evaluate the performance of gas power cycles for which the working fluid remains a gas throughout the entire cycle. Analyze vapor power.
BRAYTON CYCLE AND EFFECT OF INTERCOOLING , REHEAT AND REGENRATION
7–12 ISENTROPIC EFFICIENCIES OF STEADY-FLOW DEVICES
Unit 61: Engineering Thermodynamics
prepared by Laxmi institute tech. Mechanical eng. Department.
Chapter: 08 POWER CYCLES.
Simple Thermal Power Plant
TOPIC:- VAPOUR CYCLES CREATED BY:
VAPOR & COMBINED POWER CYCLES
Power Plant Technology Combined Cycle and Renewable Energy Power Systems (Assignment 1) by Mohamad Firdaus Basrawi, Dr. (Eng) Mechanical Engineering Faculty.
Power Plant Technology Steam and Gas Cycle Power Plant (Assignment 1)
Power Plant Technology Steam and Gas Cycle Power Plant (Lecture 2)
Power Plant Technology Steam and Gas Cycle Power Plant (Assignment 2)
GAS TURBINE POWER PLANT
Carnotization of Rankine Cycle
Furnace Heat Transfer & Steam Generation
Chapter 8 Production of Power from Heat.
9 CHAPTER Vapor and Combined Power Cycles.
ENERGY CONVERSION ES 832a Eric Savory
15. Jan Sai Thimmanoor Committee:
Generation of Most Eligible Steam for Rankine Cycle
Condenser in Power Plants
Generation of Most Eligible Steam for Rankine Cycle
Combined Cycle Power Plants
Aditya Pillai, Alihan Kaya, Michel De Paepe, Steven Lecompte
Rui Wang, Gequn Shu, Hua Tian, Xuan Wang*
Performance Analysis and Optimization of R245fa-Cyclopentane Zeotropic Mixtures in Partial Evaporating Organic Rankine Cycles (PEORC) for Low Temperature.
RMSoEE, IIT Kharagpur, India
Regenerative Rankine Cycle
Presentation transcript:

Potential of a Transcritical Regenerative Series Two Stage Organic Rankine Cycle for Dual Source Waste Heat Recovery Anandu Surendran Satyanarayanan Seshadri Ph.D Energy and Emissions Lab Department of Applied Mechanics Indian Institute of Technology| Madras 5th International Seminar on ORC Power Systems | Athens, Greece

Contents Existing ORC architectures Proposed architecture Heat source and modelling conditions Parameter studies Optimization and comparison Conclusion and future works 5th International Seminar on ORC Power Systems | Athens, Greece

Existing ORC solutions Pre-heated single stage ORC Dual-loop ORC 5th International Seminar on ORC Power Systems | Athens, Greece

Parallel Two stage ORC (PTORC) Series Two stage ORC (STORC) 5th International Seminar on ORC Power Systems | Athens, Greece

Why advanced ORC architectures for more than one heat source ? More often multiple heat sources exist concurrently Existing complex architectures are less economical All existing architectures are of lower thermal efficiency Inability to fully utilize all the heat sources when multiples heat sources are present What could be done? Supercritical evaporation Partial evaporation Utilizing superheat after expansion Reducing heat exchanger requirements Stream splitting ORC System 5th International Seminar on ORC Power Systems | Athens, Greece

What is being proposed? An advanced ORC layout: Trans-critical Regenerative Series Two Stage Organic Rankine Cycle (TR-STORC) Novel architecture that combines supercritical evaporation in high pressure (HP) stage and partial evaporation in low pressure (LP) stage Utilizes the superheat of exhaust vapour from HP turbine in the regenerator to fully evaporate the working fluid in LP stage and boost power output TR-STORC layout T-s diagram of TR-STORC 5th International Seminar on ORC Power Systems | Athens, Greece

Heat source: Stationary IC Engine 2.9 MW natural gas engine Used as stationary power generation units in steel plants and other process industries Heat Sources from a Gas Engine Engine jacket cooling water Engine lubrication oil cooling First stage air intake intercooler Engine exhaust gases Engine generator radiated heat Heat from second stage intercooler Exhaust gases Hot water First three are recovered as hot water on a 70/90°C flow return basis Primary heat source : Exhaust gases (Tp= 432°C, mp=16,528 kg/h) Secondary heat source : Hot water (Ts= 90°C, ms=50,400 kg/h) Working fluid : Cyclopentane 5th International Seminar on ORC Power Systems | Athens, Greece

Cycle parameters All processes are at steady state Value ΔT pinch HP evaporator ΔTevap,HP (K) 20 ΔT pinch LP evaporator ΔTevap,LP (K) 10 ΔT pinch condenser ΔTcond (K) Isentropic expander efficiency e (%) 70 Isentropic pump efficiency p (%) 80 Primary heat carrier pressure PP (kPa) 101.325 Primary heat source cooling limit TP, outmin (K) 373 Inlet temperature cooling water Tsink, in (K) 298 Outlet temperature cooling water Tsink, out (K) 303 All processes are at steady state Pressure drop and heat transfer from the pipelines is neglected Changes in kinetic and potential energy of the working fluid is negligible All heat exchangers are counter flow type Both LP and HP turbine stages have same isentropic efficiency MATLAB model integrated with REFPROP 5th International Seminar on ORC Power Systems | Athens, Greece

Modelling equations and procedure Discretized heat exchanger model with N=50 in HP evaporator for capturing the cooling curve and pinch point location N=30 for condenser and LP evaporator Mass flow rate in HP and LP loops are calculated iteratively Search technique to find the optimum vapor fraction in LP evaporator outlet 5th International Seminar on ORC Power Systems | Athens, Greece

Influence of HP evaporation pressure and vapor outlet temperature At lower HP evaporator pressures, lower values of vapor outlet temperatures lead to maximum work output For higher HP stage pressures ,the optimum vapor fraction is higher for a given vapour outlet temperature 5th International Seminar on ORC Power Systems | Athens, Greece

Influence of HP evaporation pressure and vapor outlet temperature Up remains almost constant with vapour outlet temperature The peaks in Us correspond to maximum mass flow rates in the pre-heater section of LP evaporator The variation in thermal efficiency is a direct result of the variation in net power output and heat source utilization rates 5th International Seminar on ORC Power Systems | Athens, Greece

Influence of LP evaporation temperature (pressure) At lower values of T3, higher utilization of secondary heat is seen At lower values of T3, the thermal efficiency of the LP stage decreases resulting in lower power outputs An intermediate value of T3 exists that maximizes the net power output of the TR- STORC. 5th International Seminar on ORC Power Systems | Athens, Greece

Cycle optimization : Parameters and Constraints Value T6 560-600K T3 323K –(Ts,in -ΔTevap,LP)K PHP evap 1.1 Pc- 8MPa Tcond 313K-333K Constraints Pcond 1.20 bar VFR HP turbine <= 50 VFR LP turbine Degree of sub cooling 5K Tp,out min 373K GA parameters Population size 20 Maximum generations 15 Function tolerance 0.01kW The maximum operating temperature of the working fluid is set as the upper limit on the vapor outlet temperature Condenser pressure is kept above atmospheric pressure to prevent air leakage into the system Volumetric flow ratios (VFR) of both HP and LP turbines are constrained within 50 so that single stage turbines with can be used (Invernizziet al., 2007) The cooling limit on the primary heat source is set to 373K to prevent acid droplet formation Genetic Algorithm (GA) with net power output as the objective function Compared with an optimized STORC and pre-heated ORC for various cases 5th International Seminar on ORC Power Systems | Athens, Greece

Optimization results : At engine design point Parameters Pre-heated ORC STORC TR-STORC Wnet (kW) 280 297 344 I (%) 14.4 12.2 15.3 ex(%) 14.2 15.0 17.4 Up (%) 81.5 81.6 Us (%) 5.20 18.4 13.3 mwf(kg/s) 3.50 4.85 4.84 Tevap,LP (K) - 347 Tevap,HP (K) 460 582 Pevap,HP (MPa) 2.18 6.83 VFRLP 1.6 1.7 VFRHP 21.6 13.5 45.2 UA (kW/K) 117 147 149 W/UA 2.46 2.02 2.31 TR-STORC delivers the highest power output which is 16% higher than STORC and 23% than pre-heated ORC TR-STORC also has the highest thermal efficiency, 6% higher than pre-heated ORC and 25% higher than STORC Us increased by 2.6 times than pre-heated ORC Comparable mass flow rates and UA requirements with STORC 5th International Seminar on ORC Power Systems | Athens, Greece

Optimization results : Influence of heat source temperatures and heat content Tp= 673K , Ts= 363K Baseline : Pre-heated single stage ORC 14%-20% more power output than STORC As the secondary heat source temperature increases, the relative increase in power output of TR-STORC and STORC exceeds that of pre-heated For the heat ratios investigated, TR-STORC delivers 4.8-5.5% increased power output than STORC. 5th International Seminar on ORC Power Systems | Athens, Greece

Summary and Conclusions A two stage cycle architecture that improves on the existing STORC architecture by combining supercritical heating in the HP stage and partial evaporation and regeneration in the LP stage is proposed 2.9MW Stationary gas engine is selected as the heat source Results are compared with optimized pre-heated ORC and STORC The main conclusions are: For a 2.9MW natural gas engine, TR-STORC delivers 16% and 23% higher power output than STORC and pre-heated ORC respectively Us increased by 2.6 times than pre-heated ORC TR-STORC has 6% and 25& higher thermal efficiency than pre-heated ORC and STORC TR-STORC presents excellent exergetic performance for dual source heat recovery over STORC and pre-heated ORC 5th International Seminar on ORC Power Systems | Athens, Greece

Future works and leads Other possibilities Experimental validation of heat exchanger loop – using throttle valves (in progress at IIT M) Experimental validation – using expanders Study of supercritical nature of refrigerants, siloxanes and other alkanes Other possibilities WHR for petroleum refineries with multiple heat streams Combined solar+ geothermal applications Single heat source applications such as geothermal by temperature splitting Compete against supercritical CO2 systems at higher source temperatures 5th International Seminar on ORC Power Systems | Athens, Greece

Thank you.. Energy and Emissions Lab Indian Institute of Technology (IIT), Madras 5th International Seminar on ORC Power Systems | Athens, Greece

Contact details Anandu Surendran Research Scholar (Ph.D) FMB #121 Energy and Emissions Lab Fluid Mechanics Division Department of Applied Mechanics , IIT M Email: anandusurendran@smail.iitm.ac.in Ph no: 9446525291, 7550160214 Dr. Satyanarayanan Seshadri Assistant Professor FMB #201 Email: satya@iitm.ac.in Ph no: 044-2257-4078, 9845068998 Energy and Emissions Lab | Department of Applied Mechanics

Appendix At design point Pressure ratio across HP turbine : 68 bar to 2.2 bar approx : 31 Pressure ratio across LP turbine : 2.2 bar to 1.2 bar approx : 1.8 Pressure limit: 80 bar 5th International Seminar on ORC Power Systems | Athens, Greece

References L. Shi, G. Shu, H. Tian, and S. Deng, “A review of modified Organic Rankine cycles (ORCs) for internal combustion engine waste heat recovery (ICE-WHR),” Renew. Sustain. Energy Rev., vol. 92, pp. 95–110, Sep. 2018. I. Vaja and A. Gambarotta, “Internal Combustion Engine ( ICE ) bottoming with Organic Rankine Cycles ( ORCs ),” Energy, vol. 35, no. 2, pp. 1084–1093, 2010. G. Shu, L. Liu, H. Tian, H. Wei, and G. Yu, “Parametric and working fluid analysis of a dual-loop organic Rankine cycle (DORC) used in engine waste heat recovery,” Appl. Energy, vol. 113, 2014. G. Manente, A. Lazzaretto, and E. Bonamico, “Design guidelines for the choice between single and dual pressure layouts in organic Rankine cycle (ORC) systems,” Energy, vol. 123, pp. 413–431, 2017. J. Li, Z. Ge, Y. Duan, and Z. Yang, “Design and performance analyses for a novel organic Rankine cycle with supercritical-subcritical heat absorption process coupling,” Appl. Energy, vol. 235, pp. 1400–1414, Feb. 2019. S. Rech, S. Zandarin, A. Lazzaretto, and C. A. Frangopoulos, “Design and off-design models of single and two-stage ORC systems on board a LNG carrier for the search of the optimal performance and control strategy,” Appl. Energy, vol. 204, pp. 221–241, Oct. 2017. T. Chen, W. Zhuge, Y. Zhang, and L. Zhang, “A novel cascade organic Rankine cycle (ORC) system for waste heat recovery of truck diesel engines,” Energy Convers. Manag., vol. 138, pp. 210–223, 2017. T. Li, Z. Zhang, J. Lu, J. Yang, and Y. Hu, “Two-stage evaporation strategy to improve system performance for organic Rankine cycle,” Appl. Energy, vol. 150, pp. 323–334, 2015. S. Lecompte, H. Huisseune, M. Van Den Broek, and M. De Paepe, “Methodical thermodynamic analysis and regression models of organic Rankine cycle architectures for waste heat recovery,” Energy, vol. 87, pp. 60–76, 2015. U. Larsen, L. Pierobon, F. Haglind, and C. Gabrielii, “Design and optimisation of organic Rankine cycles for waste heat recovery in marine applications using the principles of natural selection,” Energy, vol. 55, pp. 803–812, 2013. C. Invernizzi, P. Iora, and P. Silva, “Bottoming micro-Rankine cycles for micro-gas turbines,” vol. 27, pp. 100–110, 2007. 5th International Seminar on ORC Power Systems | Athens, Greece