FDM (Fused Deposition Modeling)

Slides:



Advertisements
Similar presentations
TERMINOLOGY FDM: Fused deposition modeling, the 3D printing technology used by MakerBot Slicing: The act of turning a digital 3D model into thin layers.
Advertisements

Volumize3d Volumize3d Training Lesson 10 – Slicing Printing.
and Statistics, 2016, Vol. 4, No. 1, 1-8. doi: /ajams-4-1-1
Designing for Rapid Prototyping
Percentage of Polyethylene
Properties Test results
© The Author(s) Published by Science and Education Publishing.
Figure 1. Diagram of calorimeter Kl-12 Mn: 1-bomb calorimeter; 2-calorimeter cover; 3-temperature sensor; 4-cover holder with mechanical mixer drive; 5-mechanichal.
Supplier Input Process Output Customer
Modulus of elasticity (GPa) Shear modulus elasticity (GPa)
Table 2. Result of Actual Technical Writing Needs
Research, 2015, Vol. 3, No. 6, doi: /education
Table 5. Properties of The Tested Soil
Fusion temperature range Clinical Applications
Tensile strength (MPa) Length (m) of fibers/kg
Total Number of persons Tested
Table 1. Configurations of the building
Table 1. Sample Size No Category Sample Size (F) Percentage (%) 1
Total Energy Consumed (%)
Tensile Test after Firing
3D printing FDM (thermoplastics)
© The Author(s) Published by Science and Education Publishing.
Table 1. Operating Conditions
Table 4. Physicochemical properties of cyclone fly ash
© The Author(s) Published by Science and Education Publishing.
Table 1. The radial spheroidal functions
Year range Rainfall (mm) ∆s in rainfall Temp (°C) ∆s in temp RH (mm)
Total CO2 Emissions (Electricity + Fossil Fuel)
Table 4. INVESTMENTS COST
Inscribed circle diameter
XW9048(Xantrex inverters)
Table 2. Showing mean and SD along with t- critical ratio
Number of categories that are mentioned (0% < categories < 5%)
Table 1. Geometric properties of steel tubes used
Table 1. Characteristics (age, height, and weight) of the participants
Table 2. Modal parameters estimated by Pulse Reflex®
© The Author(s) Published by Science and Education Publishing.
No. Of units of single building Rated power (W) of unit load
Table 5. Pvalues of ttests for direction a
Interpass temperature
Table 2. Air-water flow cases
Table 3. Main properties of the thin brass electrode
Table 5. Maximum stress, strain and deformation values
Insulation, kWh/m²/day
Table 1. Characterization Result of Leaded Petrol and Blends
Simulation Frequency(Hz)
Table 6. Pvalues of ttests for direction b
Table 1. Descriptive Statistics
Table 2. Regression statistics for direction a
Table 3. Regression statistics for direction b
Training Programs in Management and Leadership
Average Hardness value (HRC)
Control Valve Tag Number
Behavioral strategies
Table 4. Summary of Multi ways ANOVA results
Table 4. Surface roughness (outer faces)
Table 2. Control Valves & Bypass Valves Process Data
Curve No Width of patch (W) Length of patch (L) RL Freq. Range
Control Valve Tag Number
chemistry that are involved in peer group
© The Author(s) Published by Science and Education Publishing.
Table 3. (d) Summary of two way ANOVA for overall adjustment
Table 1. K-T Diagram for Bicycle Seat
Table 3. Surface roughness (inner faces)
Table 7. The Result of T Test After Treatment
© The Author(s) Published by Science and Education Publishing.
Table 3. Simulation results
Compressive Strength difference at 1 week (MPa)
Table 6. Twisting moment of counter shaft at different torques
© The Author(s) Published by Science and Education Publishing.
Presentation transcript:

FDM (Fused Deposition Modeling) Table 1. Summary of the operating setup of the personal FDM 3D printer Parameters Values Filament Material PLA+ Colour Light Blue AM Process FDM (Fused Deposition Modeling) Layer Height (mm) 0.3, 0.2, 0.1 Infill Density (%) Nozzle Diameter (mm) 0.5, 0.3, 0.2 Nozzle Temperature (°C) 220 Printing Speed (mm/s) 30 Extrusion of Material (layer width) (mm) 0.48 Speed for non-print moves (mm) 60 Horizontal Shells (top and bottom layer) Vertical Shells 1 Cooling Rate build-in Bed Temperature (°C) Room Temperature Room Temperature (°C) 25±1 Relative Humidity (% RH) 40±5 Mohammad S. Alsoufi et al. How Surface Roughness Performance of Printed Parts Manufactured by Desktop FDM 3D Printer with PLA+ is Influenced by Measuring Direction. American Journal of Mechanical Engineering, 2017, Vol. 5, No. 5, 211-222. doi:10.12691/ajme-5-5-4 © The Author(s) 2015. Published by Science and Education Publishing.