Tutorial 1 Learning Topology Optimization Through Examples and Case Studies August 18, 2019.

Slides:

Advertisements

Similar presentations

Pre-stresses Influence on a Micro Mirror Structure.

Advertisements

Prestressed Modal Analysis Workshop 5.2. Workshop Supplement Prestressed Modal Analysis August 26, 2005 Inventory # WS5.2-2 Workshop Goals.

Symmetry & boundary conditions Joël Cugnoni, LMAF/EPFL, 2009.

Project 2: Torque-Arm Modeling, Simulation and Optimization

Mesh, Loads & Boundary conditions CAD Course © Dr Moudar Zgoul,

A “CANTILEVER” EXPERIENCE OF LARGE PROPORTIONS Pinocchio's Nose.

Procedures of Finite Element Analysis Two-Dimensional Elasticity Problems Professor M. H. Sadd.

Abstract/Objectives Better understand the effects of typical GD&T variations on Bolt Stresses in Torque Carrying Bolted Flanges Create Trend Curves for.

Optimization of a FEA Beam Element Model for Computational Speed and Accuracy Brent Weight and Ryan Weight.

2D Analyses Mesh Refinement Structural Mechanics Displacement-based Formulations.

Optimization of a Flapping Wing Irina Patrikeeva HARP REU Program Mentor: Dr. Kobayashi August 3, 2011.

The problem to be solved is specified in a) the physical domain and b) the discretized domain used by FEA Governing principle law :

June 29, The difference between two feature models Matthijs Sypkens Smit Willem F. Bronsvoort CAD ’07 Conference, Honolulu, Hawaii Faculty of Electrical.

Introduction to ABAQUS 27 th February, Units Before starting to define any model, you need to decide which system of units you will use. ABAQUS.

Structures and stress BaDI 1.

Flexible Self Locking Pin-less Joint

A Designer’s Approach for Optimizing an End-Loaded Cantilever Beam while Achieving Structural and Manufacturing Requirements Timothy M. Demers November.

RPI Master’s Project Proposal Stephen Ganz – 5/15/2012 Structural Analysis of Bridge Gusset Plates: Steel vs. Composite.

Axisymmetric Analysis of a Pipe Assembly

Project Proposal 2 Tangent Tube Slip Spacer. GOALS Determine the maximum load which the Tangent Tube Slip Spacer(TTSS) Can Support Suggest improvements.

S1-1 ADM703, Section 1, August 2005 Copyright  2005 MSC.Software Corporation PART 1 ADVANCED MODELING AND BEST PRACTICES.

Department of Civil and Environmental Engineering, The University of Melbourne Finite Element Modelling Applications (Notes prepared by A. Hira – modified.

Ansys Workbench 1 Introduction

Computer Aided Mechanical Design

Engineering 309: Machine Design I Instructor: Dr. Min Lu Presented by: Mike Kraft Thanh Nguyen.

1 Optimization of Reinforcement Methods for Non-round Pressure Vessels By Shawn McMahon A Presentation of a Thesis In Partial Fulfillment of the Requirements.

In these tutorials the use adaptive mesh refinement will be review Workbench 12.1 Aalborg Universitet esbjerg Søren Heide Lambertsen.

Form-Finding of Long Span Bridges with Continuum Topology Optimization and a Buckling Criterion Salam Rahmatalla (Graduate Student) Prof. Colby C. Swan.

Checkerboard-free topology optimization using polygonal finite elements.

Tutorial 6-1: 3D Modeling.

Kratos 3D FSI Analysis Tutorial

COMSOL Analysis: End Loaded Cantilever Beams of Various Cross Sections Gregory Hew.

Copyright© Since 2008 Seung Jo Kim Aerospace Structures Laboratory Seoul National University Seoul, Korea

OPTIMUM DESIGN Hanyang Univ. School of Mechanical Engineering Lee,gyeorye.

Structural Integrity UNDERSTAND STRUCTURAL STRENGTH OF LOAD BEARING COMPONENTS IN MECHANICAL SYSTEM.

Ashwath Department of Applied Mechanics Indian Institute of Technology Madras.

Geometry 7-R Unit 7 Area Review Problems

Date of download: 6/23/2016 Copyright © ASME. All rights reserved. From: Topology Optimization of Total Femur Structure: Application of Parameterized Level.

Chapter 5 Prism Meshing – Workshop 1 Waterjacket Section

Multi-objective optimization of nitinol stent design

Oring Constraints.

CHAP 8 STRUCTURAL DESIGN USING FINITE ELEMENTS

FEA Analysis of an Assembly with Bolt Fasteners

Date of download: 10/30/2017 Copyright © ASME. All rights reserved.

Kratos 3D Structural Analysis Tutorial

Chapter 4 Volume Meshing – Workshop 1 Engine Block Meshing

Date of download: 12/23/2017 Copyright © ASME. All rights reserved.

Date of download: 3/6/2018 Copyright © ASME. All rights reserved.

Power Magnetic Devices: A Multi-Objective Design Approach

Chapter No. 04 Equilibrium

التدريب الرياضى إعداد الدكتور طارق صلاح.

Topological Ordering Algorithm: Example

Year 1 Number – number and place value

Homework Worksheet Check 1-8 add/subtract top numbers

Bridge Truss problem I (simple truss)

Topological Ordering Algorithm: Example

Topic 6 and 7 Designing with Forces and Stable structures

Topological Ordering Algorithm: Example

Add content to the Library

Topological Ordering Algorithm: Example

Practice Geometry Practice

Journal of the American College of Surgeons

Simulation Fundamentals Static Stress/Shape Topology Tutorial

Tutorial 1 Learning Topology Optimization Through Examples and Case Studies August 18, 2019.

Tutorial 1 Learning Topology Optimization Through Examples and Case Studies August 18, 2019.

Topology Optimization through Computer Aided Software

Tutorial 1 Learning Topology Optimization Through Examples and Case Studies August 18, 2019.

Advanced Two Chapter 8 Volume and Similar Solids

Advanced Two Chapter 8 Volume and Similar Solids

Tutorial 1 Learning Topology Optimization Through Examples and Case Studies August 18, 2019.

Presentation transcript:

Tutorial 1 Learning Topology Optimization Through Examples and Case Studies August 18, 2019

Use Pareto Method for Topology Optimization Problem Description Cantilever Beam Problem Units: MKS Material: AlloySteel Structural Loads: 1000N Mesh Size: use default mesh size TopOpt Constraints: No Constraints Goal: Optimize the topology for a volume fraction of 0.25 1000N Use Pareto Method for Topology Optimization

Pareto Method based TO Choose Units Load Geometry Define Material Apply Loads (Structural/Thermal/Gravity) Carry out FEA Apply Top Opt Constraints Topology Optimization PostProcessing

Results