FANCOILS CONTROLS ELECTRONIC BOARD - KCMS CMS - KCMS/PCM CMSPCM NEW WIRED CONTROL PANEL - KPCM

FUNCTIONS

CONTROLLI NEW CONTROLLI IDROWALL FREND YARDYEV BRIOEV UTNC-EV UTNB KICM KTCM KPCM YARDYEV NEW IDROWALL FREND BRIOEV UTNC-EV BRIOEV UTNC-EV UTNB UTNA

CONTROLS CMS KCMS CMSPCM KCMS/PCM KICM KPCM KTCM RI-KRI STI KSTI MVR KMVR

CONTROLS New codes for electrical board and panel CMSPCM KCMS/PCM CMS KCMS KPCM

New electronic board KCMS CMS OLD mario SCR ECO digital input don’t change, SIC EIR change their position New digital input DI5 (not available for Frend and Idrowall) for new function: OCCUPANCY function (NC) only for KICM panel, (by modifying board parameters (P45=8;P93=3) trough installer password on the KPCM control panel)

New electronic board KCMS CMS OLD OLD NEW New digital output CCH CCA

FUNCTIONS SETTING FUNCTIONS COMFORT FUNCTIONS

FUNCTIONS SETTING FUNCTIONS Full auto Cool Dry KICM Fan KPCM Heat KTCM Heat + heater Full Auto + heater NOVELTY Full AUTO: the desired temperature is showed on the display. The unit, according to the room temperature and the setting temperature, sets the working mode (cool/heat). User set temperature Legend mode room temperature HEAT OFF COOL P02=2°C P03=2°C P04=0,5°C

FUNCTIONS ATTENTION COMFORT FUNCTIONS KICM KPCM KTCM Orienting/swing (on Idrowall) Clock Timer Sleep Hot start Too cool Memory Economy (ECO) Lock function / Blocco remoto (KICM) ON/OFF remote control (SCR) Summer/Winter remote control (EIR) Security control (SIC) Occupancy (only KICM) new Probe IN/OUT Continuous ventilation Alarm MASTER/SLAVE Periodic ventilation Confort control new Blocco tastiera (solo KTCM) KICM KPCM KTCM ATTENTION The following functions aren’t available with KICM control panel: Orienting/swing - Clock - Timer - Continuous ventilation (by key) – Keybord stop Probe IN/OUT function is available for: KICM trough DIP SWITCH (DIP6) setting KPCM trough key on the panel Not used with the remote control KTCM (the probe is always set in the unit) The periodic ventilation is always disabled with KPCM and KICM with Probe In function activated (probe into the unit) Confort control (by modifying board parameters P36=1 trough installer password on the KPCM control panel).

COMFORT CONTROL FUNCTION Comfort control (by parameters) When the set-point is decided by a system manager (supervision), the Comfort Control function gives the possibility to increase or reduce the Set-point (+-3°C) in the room with the UP-DOWN bottoms. (The function have to be enable modifying board parameters P36=1 trough installer password on the KPCM control panel.) The set value is 22 °C User set temperature 22°C Legend mode room temperature HEAT OFF COOL P02=2°C P03=2°C P04=0,5°C

LOCK FUNCTION FUNCTION Attention: to obtain the changing set-point ±3°C must be set the Confort Control Function

DIP-SWITCHES Changes to the DIP-Switches must be made with the board disconnected from the power supply. The DIP-Switches on the electronic board (see right figure) can be changed using a sharp tool. The DIP-Switches can be changed correctly by following the instructions present on the component and in the following table. OLD NEW

DIGITAL INPUT/FUNCTION: OCCUPANCY (NOT FOR IDROWALL FREND* ) ONLY x KICM In case of supervising system (BMS) with OCCUPANCY function it is possible to activate 3 different working modes (by modifying board parameters P45=8; P93=3 trough installer password (60) on the panel): Not booked room = OFF Occupied room = Comfort mode Booked and not occupied room = Stand-by/Economy mode Not occupied OFF Occupied Comfort mode There is a person in the room. The fancoil works with desired temperature value for fixed time (15 min). Set-point = desired temperature value The occupancy status can be activated: By one of the keys in the panel (not ON/OFF) for a set period of time (parameter P94=15 min). At the end of the time periods (15 min) the occupancy status can be enabled again With movement sensor on DI5 digital input Pressing Sleep key for 5 sec the Occupancy function continues up to unit switch-off Booked and not occupied Stand-by/Economy mode There is no person in the room. The fancoil works with economy set-point for energy savings Set-point = economy * Only with ECO (DI4, parameter P44=8) NOTA BENE Con funzione Occupancy abilitata non utilizzare l’ingresso igitale ECONOMY

DIGITAL OUTPUT: FUNCTION CCH Chiller input, chilled water required from the thermostat (NO) CCH –Chiller input

DIGITAL OUTPUT: FUNCTION CCA Boiler input, hot water required from the thermostat (NO) CCA – Boiler input