1.7 Isometric Drawing 1. Opener D Q F R E A G Identify: a) AR b) GA

Slides:

Advertisements

Similar presentations

SURFACE AREA and VOLUME with BASE 10 BLOCKS

Advertisements

Module 4: Isometric Drawing

SURFACE AREA and VOLUME of RECTANGULAR PRISMS and CUBES.

From Isometric Drawings to Plans and Elevations

GEOMETRY Eqao preparation day 5.

Representations of Three-Dimensional Figures

CONFIDENTIAL 1 Geometry Representations of Three- Dimensional Figures Geometry Representations of Three- Dimensional Figures.

Geometry Perspectives

Isometric projection Projection on a plane such that mutually perpendicular edges appear at 120o to each other. Iso (same) angle between the axes. Example.

Technical Drawing Visual Communication of Technical Information

THIS IS With Host... Your Anglers Choice Tri- it out! Is a Square just a Square? The 3 rd Dimension Geo. Splash You should see.

1-1 Nets and Drawings for Visualizing Geometry

Chapter 8 Introductory Geometry Section 8.6 Viewing and Drawing Solid Figures.

Drawings and Nets Chapter 1 Section1 Geometry Mr. Miller.

prism with 6 square faces

Nets and Drawing for Visualizing Geometry

Chapter 1: Tools of Geometry

Lesson 12-1 Pages Drawing Three- Dimensional Figures.

Lesson 11-2 Nets and Surface Area.

Please get the warm up off the back desk and begin working.

Textbook - page 10 Lined paper. Vocabulary An isometric drawing of a three dimensional object shows three sides of a figure from a corner view. Workbook.

Drawings, Nets, and Other Models Drawings, Nets, and Other Models

Engineering 1182 College of Engineering Engineering Education Innovation Center Basic Isometric Sketching and Coded Plans Chapter 2 of Text.

Geometry 12.1/2 Representations of 3-d Figures Surface Area of Prisms and Cylinders.

Make an isometric drawing of the cube structure below.

Holt Geometry 10-2 Representations of Three-Dimensional Figures Warm Up Write a description of each figure. 1. cube 2. pentagonal prism 3. cylinder prism.

Using Drawings to Communicate Lecture 3 –How to create an isometric drawing of a part when given front, top, & right side views.

Warm-Up What 3-d geometric shape will the following nets fold to create? 1) 2) 3)

Holt Geometry 10-2 Representations of Three-Dimensional Figures 10-2 Representations of Three-Dimensional Figures Holt Geometry Warm Up Warm Up Lesson.

10-1 & 10-2: Space Figures, Nets & Diagrams

Technical Drawings Isometric (3D) & Orthographic Projections (OP’s)

Nets and Drawings for Visualizing Geometry

Holt Geometry 10-2 Representations of Three-Dimensional Figures 10-2 Representations of Three-Dimensional Figures Holt Geometry Warm Up Warm Up Lesson.

Section 4.1: polygons.

Isometric Drawings & Orthographic Drawings Tutorial 5d.

Chapter 10 Measurement Section 10.5 Surface Area.

Please get the warm up off the back desk and begin working.

Nets & Drawings for Visualizing Geometry Section 1-1.

PREPARING FOR SURFACE AREA AND VOLUME DRAWINGS, CROSS SECTIONS AND NETS.

Drawing Two Dimensional Shapes

1.2 Drawings, Nets, and Other Models

Nets and Drawings for Visualizing Geometry

Section 1.1 Nets and Drawings for Visualizing Geometry

Using One Point Perspective to Combine Shapes

Section 1.1 – Nets and Drawings for Visualizing Geometry

Representations of Three-Dimensional Figures

1.6 Two Dimensional Figures

Section 11-7 Ratios of Areas.

Basic Isometric Sketching and Coded Plans

UNIT – IV (a) Development of surfaces: Introduction, methods of development, development of lateral surfaces of right solids, cube, prisms, cylinders,

3D objects Saturday, 17 November 2018.

Lesson 54 Representing Solids.

10-2 Warm Up Lesson Presentation Lesson Quiz

Using One Point Perspective to Combine Shapes

Are the buildings below three dimensional shapes?

3D objects Thursday, 28 February 2019.

Maths Unit 20 – Visualisation, Nets and Isometric Drawing

ENGN103 Engineering Drawing orthographic projections

Visualizing Geometry Skill 01.

3-D Views of Solid Figures

2-Dimensional Figures Classifying Triangles and Quadrilaterals

ENGN103 Engineering Drawing orthographic projections

S1 Orthographic Sketching

ENGN103 Engineering Drawing orthographic projections

3-D Shapes Topic 14: Lesson 2

2 POINT PERSPECTIVE.

1.2: Drawings, Nets, and other models

Presentation transcript:

1.7 Isometric Drawing 1. Opener D Q F R E A G Identify: a) AR b) GA c) QE d) DF e) AE f) EAQ g) AQ h) Draw an equiangular quadrilateral. What’s another name for this? i) Draw an equilateral quadrilateral. What’s another name for this? j) What is the most common high school and college mascot? A F D E R G Q The eagle

2. Notes: Isometric and Foundation Drawing shows a corner view of a figure. It is not drawn in perspective and distances are not distorted. isometric drawing

2. Notes: Isometric and Foundation Drawing the top view, front view, and right-side view of a three-dimensional figure.

Make an isometric drawing of the cube structure below. You will draw all the edges of the figure that you can see.

Identify the square that represents the tallest part Identify the square that represents the tallest part. Write the number 2 in the back square to indicate that the back section is 2 cubes high. Write the number 1 in each of the two front squares to indicate that each front section is 1 cube high.

3. Classwork: Isometric Drawings 2 3 1

3. Classwork: Isometric Drawings

3. Classwork: Isometric Drawings Start from the top and draw your way down. Erase the lines you shouldn’t be able to see. 3 2 1

3. Classwork: Isometric Drawings 2 1

3. Classwork: Isometric Drawings

3. Classwork: Isometric Drawings 2 1

3. Classwork: Isometric Drawings

3. Classwork: Isometric Drawings 4 1 3

3. Classwork: Isometric Drawings

3. Classwork: Isometric Drawings

3. Classwork: Isometric Drawings 5 4 2 3