Title: Name 最终装配垂直度检验 On this page is information about operators that are trained and certified to perform this Standard Work. The operators signing below have read this SWI and have successfully performed the work described in it in the presence of the Supervisor or Engineer signing in the second column on the date in the third column. Trained and capable of performing this work: Supervisor or engineer giving Approving to perform: Date: Operator 1 Operator 2 Operator 3 Operator 4 Operator 5 Operator 6

Perpendicularity Tolerances Title: Name Safety Requirements: Safety glasses Operator Maintenance 1) 2) 3) 4) 5) Tools & Fixtures 1) 2) 3) 4) 5) Material / Components 1) Mechanical sheet 2) Print 3) 4) 5) In Process Check 1)开始检验前，参考图纸或检查表上的可接收垂直度公差. 2) Mechanical sheet Perpendicularity Tolerances

2. 将指示器夹在轴端上. (注意: 有些夹指示器轴太短.) Title: Name Safety Requirements: Safety glasses Operator Maintenance 1) Verify calibration on dial indicator. 2) 3) 4) 5) Tools & Fixtures 1)V-block fixture 2)Dial indicator 3) 4) 5) Material / Components 1) motor 2) 3) 4) 5) In Process Check 1)如果轴太长，请将两块V型块叠放保证足够的空间. 2) 确保电机水平安全地放置在V型块上. 1. 将电机垂直置于V型块上 2. 将指示器夹在轴端上. (注意: 有些夹指示器轴太短.)

正确的表角度 错误的表角度 3. 将测试器的面和指针尽可能于被测表面平行. 真确的指针角度 错误的指针角度 减小此角度 Title: Name Safety Requirements: Safety glasses Operator Maintenance 1) 2) 3) 4) 5) Tools & Fixtures 1) 2) 3) 4) 5) Material / Components 1) motor 2) 3) 4) 5) In Process Check 验证测量值不能超过表的量程. (测量器的表应在“0”～“1”) 正确的表角度 错误的表角度 3. 将测试器的面和指针尽可能于被测表面平行. 真确的指针角度 错误的指针角度 减小此角度

4. 将针头置于被测表面，保证针头尽可能远离中心 Title: Name Safety Requirements: Safety glasses Operator Maintenance 1) 2) 3) 4) 5) Tools & Fixtures 1) 2) 3) 4) 5) Material / Components 1) 2) 3) 4) 5) In Process Check 1)Verify that indicator will not run out of travel distance. 2)在第5步旋转过程应避免指针碰到障碍物 (洞, 突起, ect.) 4. 将针头置于被测表面，保证针头尽可能远离中心 5. 旋转时指示器清零 6. 360度旋转千分表读取每个数值的总和（例如：右边0.0021＋左边0.0090＝总和为0.0030）

Record variance measured by dial indicator on mechanical sheet. Title: Name Safety Requirements: Safety glasses Operator Maintenance 1) 2) 3) 4) 5) Tools & Fixtures 1) 2) 3) 4) 5) Material / Components 1) 2) 3) 4) 5) In Process Check 1) 测量值需在图纸或检查表的公差范围以内才算合格Measurements must be within the tolerance on the Mechanical Sheet and Print to pass inspection. 2) 7. 在表单上记录测量变化值 Record variance measured by dial indicator on mechanical sheet. 8.重复1～7步测量图纸上其它表面的垂直度 Repeat steps 1 through 7 to measure the perpendicularity of any other surface on the print.

Signatures of Authorization Revision: Date: Reason for Change: Editor: A 9-26-06 New SWI Into. Tony Dick Signatures of Authorization Production: Manufacturing: Quality: Design: Other: