KX-TDA200/100 System (Ver.1.1) Enhanced Items 2004.05.14 Edition 1.0 - First Edition 2004.05.21 Edition 1.1 - Some information is modified, I don’t remember where I modified. (Nagayama) 2004.05.24 Edition 1.2 2004.07.07 Edition 1.3 - BRI4 information is deleted because it’s not new hardware. Panasonic Communications Co., Ltd. Network Business Company Edition 1.3 07 Jul., 2004

General System Highlight New Features Condition of New Features Software Compatibility

System Highlight V1.0 Networking(QSIG), Call Center, VoIP Gateway, CTI (CSTA/TAPI), T76xx Line Up, Wireless System V1.1 - Digital XDP & Double Extension Capacity by MEC - New VoIP Gateway Card (Panasonic proprietary) - New CS to DPT Port - And other new features

New Features Hardware Function Improvement Highlight Making calls Receiving calls Hold/FWD/TR Conference Timer Others Programming BRI4, IPGW4E, CSIF4, 2chCS, MEC DXDP & Double Extension Capacity New IPGW Card 2chCS Broadcasting Dialing Plan Ext. CLIP sending on Emergency Call Short Cut Access to System Speed Dial Modified DDI Number is displayed on LCD Improved DSS LED Flash / Call Pick up Disable Hold Recall Disable re-count Ext-CO Duration Limitation by Hold Retrieve ISDN-3party Conference DTMF Tone through a Conference from PT Intercept Timer for each time mode(Day/Night/Lunch/Break) SMDR RC/AN information output Paging to other paging group COS Name is programmable CS port Name is programmable Ext. CLIP Automatic Generating DDI/DID Name Automatic Generating Wireless XDP Programming from PC Logical Check PS Hand-Over during Conference Call Walking Extension from Fault Extension

Condition of New Features DXDP Double Extension Capacity 2chCS Broadcasting Another Features Software Condition DHLC/DLC = 2.005 No Hardware Condition MEC(TDA0105)

Software Compatibility MPR / LPR MPR 1.1xx MPR 1.0xx YES YES w/o DXDP, TDA0141 DLC/DHLC 2.005 DLC/DHLC 1.xxx MPR / PC maintenance console MPR 1.1xx MPR 1.0xx YES NO 1.07 1.06

- New Hardware - Power Factor Summary

New Hardware IPGW4E CSIF4 2ch CS MEC KX-TDA0484 TDA200 4 TDA100 2 (4ch VoIP Gateway) KX-TDA0484 TDA200 4 TDA100 2 4-channel VoIP gateway VoIP H.323 V.2, ITU-T G.729a, G.723.1, G.711 T38 (FAX) is not supported Panasonic proprietary IPGW card CSIF4 TDA200 4 TDA100 2 4-port CS interface card for 4 CSs(TDA0142). (4 Cell Station Interface) KX-TDA0143 2ch CS TDA200 32 TDA100 16 Connect to DPT port (CSIF card is not needed) 2.4GHz (KX-TDA0141), DECT(KX-TDA0141CE) (CS to DPT Port) KX-TDA0141 MEC TDA200 1 TDA100 1 * Memory expansion for - Broadcasting feature - Double the number of DPTs (DXDP) [2004.07.07 - Mr.Narikiyo’s pointing from China.] BRI4 information is deleted, because this card is not new hardware, it has already been released from V1.0. (Memory Expansion Card) KX-TDA0105 * To be installed in the MEC slot on MPR card

Power factor summary (Ver. 1.1) Trunk Card Extension Card Other Terminals IPGW4 PRI-30 BRI-8 BRI-4 CID (CO) E1 E&M LCOT-16 LCOT-8 LPR Card TDA0480 TDA0290 TDA0288 TDA0284 TDA0193 TDA0188 TDA0184 TDA0181 TDA0180 Model Power units IPGW4E TDA0484 MSLC-16 SLC-16 DHLC-8 DLC-16 DLC-8 SLC-8 LPR Card Model Power units CS I/F-8 TDA0175 TDA0174 TDA0170 TDA0172 TDA0171 TDA0173 TDA0144 16/Card* 8/Card* CS I/F-4 TDA0143 * Calculated with base card, not using base ports. [2004.07.07 - Mr.Narikiyo’s pointing from China.] The yellow marking of BRI-4 is unmarked. Because this card is not new hardware. MSG RMT TDA0191 TDA0196 CTI-LINK TDA0410 Echo DPH-2/4 TDA0166 TDA0161/162 MEC TDA0105 Voice Mail (D-PT) T72xx/T74xx/T75xx BRI Extension T76xx, T7560, T7565 1/Extension 2/Port (2ch) 4/Extension CS (TDA0142) 4/CS CS (TDA0141) APT & DSS console SLT

DXDP & Double Extension Capacity New IPGW Card 2ch CS Function - Highlight DXDP & Double Extension Capacity New IPGW Card 2ch CS

Digital XDP (DXDP) -1 - DPT on DPT without additional HW or SW - Easy installation for additional Extensions - 1 DHLC port => 3 telephones (2x DPT+1x SLT) * DHLC Card = Max 24 Ext. - 1 DLC port => 2 telephones (2x DPT) * DLC16 Card = Max 32 Ext. * DLC8 Card = Max 16 Ext. DXDP-Slave or XDP 4 Wires 2 Wires XDP DHLC Port SLT DXDP-Master DXDP-Slave DLC Port

Digital XDP (DXDP) -2 Capacity for Extension V1.0 V1.1 DXDP MEC TDA100 TDA200 No Yes Max 64 Ext. Max 128 Ext. Max 256 Ext. Additional DPT can be installed without buying another DHLC or DLC, but total capacity does not change without MEC. System Capacity (Trunk & Extension mixed) V1.0 TDA100 80 (108) ports TDA200 160 (216) ports V1.1 with DXDP&MEC TDA100 144 (158) ports TDA200 288 (316) ports

Digital XDP (DXDP) -3 MEC(TDA0105) PU for extension cards How to check the TDA0105 If the TDA0105 is not installed. If the TDA0105 is installed. Click” DHLC-8 8 (Fixed) + Connected PT/DSS/VM SLC-8 8 (Fixed) DLC-8 Connected PT/DSS/VM SLC-16 16 (Fixed) DLC-16 Connected PT/DSS/VM PU for extension cards If connected extension is exceed 128 with M type PSU, what happens? - 129th Extension (PT) will not come in service. - Minor error log = PT Connection Over.

Digital XDP (DXDP) -4 No! DXDP-Slave ø0.4mm Max.40m ø0.5mm Max.50m DXDP-Master Condition-1 ø0.4mm Max. 500m ø0.5mm Max. 720m ø0.6mm Max. 830m Master Slave - T7625 - T7630 - T7633 - T7636 - T7665 Telephone Can be used - A-PT - T72xx - T74xx - T75xx DSS CS Can not be used Condition-2 Condition-3 - OHCA function can not be used - T7601 (USB) can not be used (PC Phone / PC Console / PC Programming) Condition-4 No! Parallel Connection !

VoIP Gateway Card (KX-TDA0484) - 1 General - 4ch IPGW Card - G729a/G723.1/G711 - T.38 (FAX) mode is not supported (FAX = G711) - Physical I/F: 10/100 Base-T - Web programming (English) - Interoperability with TDA0480: Incoming call, Outgoing call and CLIP only. - Interoperability with another manufacturers : Not guaranteed. 1st Time Setup Connection TDA100/200 TDA0484 10/100 Base-T Cross Cable (http://192.168.1.200) Pattern 1 10/100 Base-T Straight Cable Switching HUB Pattern 2 IE5 or later

VoIP Gateway Card (KX-TDA0484) - 2 New IPGW Card (Compatibility) TDA0480 TDA0484/TDA3480 Compatibility DHCP QSIG service Max networked IPGW cards Voice Codec FAX Protocol Echo canceller G.165/G.168 AGC DTMF Tone Detection SNMP Event Notice by email NAT Signalling Yes (Client) H.323 V4 Annex M1 511 G.711/G.723.1/G.729a G.711 16ms No Yes H.323 V2 No Proprietary 511 G.723/G.729a T.38 16ms Yes H.323 V2

VoIP Gateway Card (KX-TDA0484) - 3 New IPGW Card (Interoperability) Function CLIR COLP COLR CNIP CNIR CONP CONR CT(Avoid tromboned) CF(Avoid tromboned) CCBS CLIP Making/Receiving call FAX Connection TDA0484/TDA3480 connect to OK TDA0484/TDA3480 connect to TDA0480 No OK TDA0480 connect to OK

VoIP Gateway Card (KX-TDA0484) - 4 How to connect TDA0480 & TDA0484… Outline of example Subnet Mask:255.255.255.0 Default GW: 192.168.1.1 PBX Code = 81 TDA0484 TDA0480 PBX Code = 82 Switching HUB TRG2 A-low A-low TRG2 IP_Address: 192.168.1.200 IP_Address: 192.168.1.12 IP_Address: 192.168.1.100 Ext.102 TIE Access = 7 Ext.103 TIE Access = 7 TIE Routing Table Lead : 82 Remove : 0 Added : none Trunk : 02 TIE Routing Table Lead : 81 Remove : 0 Added : none Trunk : 02 Dial = [7]+[82]+[103]  103 of PBX82 Dial = [7]+[81]+[102]  102 of PBX81

VoIP Gateway Card (KX-TDA0484) - 5 TDA0484 Setting Port 1 Port 2 BRI -QSIG Incoming 81102 PBX Code = 81 TDA0484 TRG 2 IP Network Outgoing 82103 * Address Setting (IP Address of Card) 1.Programming 1.1 Network Settings, General 1.1.1 IP Address Setting IP Address : 192.168.1.200 Subnet Mask: 255.255.255.0 Default GW : 192.168.1.1 1.Programming 1.4 VoIP Gateway/IP-PBX Interface Settings 1.4.2 Others G711 A-Law * Interface between IPGW & PBX * Handling setting for Incoming Call from IP Network 1.Programming 1.5 Hunt Pattern (for Incoming Group) Hunt Group Grp1 = Port 1 & Port 2 Grp2 = none Hunt Pattern 1: Rcv Leading Digit = 81, Hunt Group = 1 * Handling setting for Outgoing Call from PBX to IP Network 1.Programming 1.6 DN2IP (Dialed Number to IP Address Translation) 1.6.1 GW Entry 1.6.2 DN2IP Entry GW No.= 1 Comment = 82 Office, TDA0480 IP Address = 192.168.1.12 Group No. = 0 Leading No. = 82 Remaining Number of Digits = 3 GW No./Group No. Selection = GW GW No./Group No. = 1

VoIP Gateway Card (KX-TDA0484) - 6 TDA0480 Setting General Tab IP Address : 192.168.1.12 Subnet Mask : 255.255.255.0 Rout Address 1: 192.168.1.1 Rout Address 2: none Trunk Data Tab Port1 Trunk Group #1 Interface type = Basic Interface Length of call reference = 1 Port2 --- same as Port1 Configuration = QSIG Hunt pattern Tab --- Incoming call Handling Destination Number = 82 Hunt pattern = 1 Trunk priority Tab Hunt pattern 1: Priority1 = Trunk group#1 (Default) Other Tab A-law/m-law flag = A-law Configuration procedure 1. Configure TDA0480 own setting 2. Create “Other Unit” --- TDA0484 IP Address 3. Edit DNS table and send to TDA0480 4. Reset PBX after sending all data for TDA0480 DNS Editing Terminal = 81 Remaining digits = 3 Selected unit = TDA0484 Unit ICON

VoIP Gateway Card (KX-TDA0484) - 7 GW Grouping (Slide Call feature) ＩＰ Network Grouping In the case that TDA has more than an IP-GW, you can group these IP-GWs. Benefit of the GW Grouping : Slide Call In the case that the IP-GW(a) is not available because all channels are in use for example, originating IP-GW try the IP-GW(b). ＩＰ Network Not available Originating IP-GW IP-GW(b). IP-GW(a).

2ch Cell Station (KX-TDA0141) -1 - Two Voice Paths per CS. - A specific CS I/F card is not needed. - A port on DHLC and DLC cards can used as the interface for KX-TDA0141. - Max. number of CS: TDA100=16 TDA200=32 (Including TDA0142). - DHLC/DLC cards software must be 2.005 or later. - Functionality : The same as TDA0142 - Hand-over TDA0141  TDA0142: “YES” - Power factor is 4. TDA0141&TDA0142 total Max.32 CS / TDA200 Max.16 CS / TDA100 4 PU / CS ø0.4mm 222m ø0.5mm 347m (CAT5) ø0.6mm 500m DHLC DLC TDA0144 TDA0143 TDA0142 TDA0141 - CS Port assignment is not needed. The TDA automatically detects the connected CS (as same as DPT connection).

2ch Cell Station (KX-TDA0141) -2 How to update the CS software 1- Set a CS port to “OUS” 2- Go to “SD Card File View and Load” 3- Select “PDCSDECT” (or “PDCS24G”) 4- Click “Detail” 5- Take the same procedure of Ver.1.0

Function – Making Calls Broadcasting Dialing Plan Ext. CLIP sending on Emergency Call Short Cut Access to System Speed Dial

The caller receives C.Tone for each time. Broadcasting - 1 An PT user (Owner) can make one way path call (= announce) to 31 parties simultaneously. After one of called party answering, the owner can begin announcement. This feature requires MEC(Memory Expansion Card : KX-TDA0105). Configuration Operation 2.System - 4.Timers & Counters - 2.DISA/DPH/CONF/T.Reminder "Answer Waiting Timer for Broadcasting Group (s)" = 0 - 120 COS: “Broadcasting Operation” = Enable Owner If no member answer, I cancel broadcasting and send busy tone to the caller. 211 212 213 214 215 FWD to somewhere Announce [1] [*32]+ One Way Path PT only The caller receives C.Tone for each time. C.Tone Off-Hook C.Tone No Ring C.Tone Off-Hook 211 212 213 214 215 8 Groups / System Off-Hook Override FWD setting - Wired Extension - PS Other PBX’s Extension (Only Closed Numbering)* - Outside Telephone Number * *: Only available when the networking type of the trunk is assigned as private. * Up to 32 digits In case of No Answer, it will be disconnected by timer. Max.31 members Because of DND / PS in XDP Parallel Restriction from TRS/Barring / Call Charge Limit

Conversation with the Owner Broadcasting - 2 Conversation during broadcasting 1.To let members join to conversation Announce 211 Member-01 212 Member-02 213 Member-03 214 Member-04 215 Member-05 Joining Order 1st --- 2nd --- 3rd --- 201 The owner (2) Ext.212 --- By (1) (1) Notification Tone Ext.211 --- By (2) Ext.214 --- By (3) LCD: Ext.214 wants conversation ! (3) Conversation with the Owner = Max.3 Members (1) The Owner pushed [DSS - 212] => Ext.212 join to conference (2) The Owner pushed [Conf.] => Youngest Member (=Ext.211) join to conference ( 4 Party Conference ) (3) Listening Member pushed [DSS - 201] or Recall/Hookswitch => Notification Tone goes to the owner, Member’s information appear on the Owner’s LCD. => The Owner push [DSS - 214] => Ext.214 join to conference 2.To let members leave from conversation In above situation, when the owner does following action… Push [DSS-211] Push [Transfer] Push [Flash/Recall] Ext.211 goes back to be a listener Last joined member (=Ext.214) goes back to be a listener Last joined member (=Ext.214) is disconnected from broadcasting.

Name of Broadcasting Group LCD Display in typical condition In establishing From an owner Extension, Dial *32 + Broadcasting group number Owner Extension Called Extension Name of Broadcasting Group Conference1: PCCUK In broadcasting When a member of the group answers the call. Owner Extension Called Extension No of member Conference : 2 Conference

Condition of Member Ext. Response for Arriving Broadcasting Call Additional information Conditions and Responses of Member Extension Internal Call Block is Block Set to Call FWD Set to DND Busy Auto Answer Wireless XDP PS Condition of Member Ext. Response for Arriving Broadcasting Call The broadcast call arrives this extension. The broadcast call does not arrive this extension. Call Waiting function will be performed. The Auto Answer function will not be performed. The broadcast call does not arrive this PS. DSS key of Owner Extension which relates with member extension If owner extension has DSS key of a member of broadcasting group and establishes a broadcasting call, the DSS key does not flash when the called extension rings. It actually turns red (not flashing).

Dialing Plan Making a Call with Analog CO Voice Path Tx: Mute Rx: OK ( during Dialing ) PBX recognizes the end of dialing! Tx: OK ( Start of Dialing ) ( End of Dialing ) Dialing Plan is working is not working Inter Digit Timer expired ! Making a Call with Analog CO Inter Digit Timer - PBX can know the end of dialing by Dialing Plan Table. - It works for ISDN Enblock dial mode and Analog CO. - Typical configuration by “Auto Assign”. (Type A/B/C/D/E) - Dialing Plan Table is assigned for each TRG. - PBX sends all of the dialed digits at once after all digits dialed. 1-15s Dialing Plan Table for each TRG (Table1 – Table4) Max.32 digits 4 Tables independently 1: N11 2: NXXXXXX 3: 1NXXNXXXXXX 2: NNXXXXX 3: 1NPXNXXXXXX 3: 1NNXXXXX 4: 1NPXNXXXXXX 2: NXXNXXXXXX 48: N11 49: NXXXXXX 50: 1NXXNXXXXXX Type-A Type-B Type-C Type-D Type-E N = 2-9 P = 0,1 X = 0-9,*,# Max.50 leading numbers

Ext. CLIP sending on Emergency Call It overrides CLIR / CO Line CLIP. Ext.CLIP is sent to PRI public network as “Location Identification Number”, even if CLIR is set or CLIP mode is “CO Line CLIP”. This feature works only for Emergency call. “E911 service” must be enabled. Yes

Short Cut Access to System Speed Dial [Auto] + [JOG] or [Navi-Down/UP] works as short cut key. --- TDA30 V1.0 too - TDA100/200 Ver.1.0 “AUTO DIAL”  Nothing Happens - TDA100/200 Ver.1.1 (TDA30 Ver.1.0) “” or “” Allen, David Allen, Steve Azure, Alf “AUTO DIAL”    System Directory Name ?>   “ENTER”  Daly, Gill Darcy, Nigel Davies, Allan

Function – Receiving Calls Modified DDI Number is displayed on LCD Disable DSS Flash

Modified DDI Number is displayed on LCD - TDA100/200 Ver.1.0 Ext. 201: DDI 654201 654201 ISDN 201 4772111 (CLIP) Line 001: 201 (DDI) Caller 4772111 - TDA100/200 Ver.1.1 DIL Table & Port setting DDI Table ISDN Ext. 201: DDI 654201 201 654201 Caller 4772111 4772111 (CLIP) Line 001: 654201 (DDI)

Improved DSS LED flashing/Pick up call -1 External Call to Extension directly Ext. 202 201 - TDA100/200 Ver.1.0 The DSS LED on Ext.202 is flashing. The call can be picked up by pressing the button. External Call Ext. 201 All DSS LED’s flashing look like a Xmas tree.  Annoying!!! - TDA100/200 Ver.1.1 Two options: - The DSS LED on Ext.202 will flash. The call can be picked up by pressing the button. - The DSS LED on Ext.202 will turn ON. The call cannot be picked up by pressing the button. Busy tone is sent if the DSS button is pressed. Enable : DSS LED will flash Disable : DSS LED will turn ON New program item

Improved DSS LED flashing/Pick up call -2 External Call to ICD-Group directly Ext. 201 Ext. 202 201 External Call ICD-G 280 - TDA100/200 Ver.1.0 The DSS LED on Ext.202 flashes. The call can be picked up by pressing the button. - TDA100/200 Ver.1.1 Two options: - The DSS LED on Ext.202 will flash. The call can be picked up by pressing the button. - The DSS LED on Ext.202 will turn ON. The call cannot be picked up by pressing the button. Busy tone is sent if the DSS button is pressed. Enable : DSS LED will flash Disable : DSS LED will turn ON New item

Improved DSS LED flashing/Pick up call -3 It is possible to disable DSS LED’s turning off for an incoming call. New item ON or Flash : DSS LED turns ON or flashes for an incoming call. OFF : DSS LED never turns ON nor flashes for an incoming call. If the DSS button is pressed when extension is ringing, Call pick up by DSS key = Disable Call pick up by DSS key = Enable DSS Key mode = ON DSS Key mode = OFF LED: Flashing LED : ON It is possible to pick up call Busy Tone LED: OFF Call arrives at extension

Function – Hold/FWD/TR Disable Hold Recall Disable re-count Ext-CO Duration Limitation

Disable Hold Recall Disable Hold Recall is available if Hold Recall Timer is 0. 1-240: Hold Recall works 0 : does not work V1.0 does not have.

Disable Re-counting Ext-CO Duration Timer Disable re-count Ext-CO Duration Limitation by Hold Retrieve Extn-CO Duration Timer Calling Party Called Party Call dest. Party Place on Hold Hold Retrive Answer Ringing (Establishing a Call) (In Conversation) (On Hold to transfer) Time flow Start ReStart V1.0 V1.1 - Ext 201 makes an external call. - Extension-CO duration timer on Ext 201 starts when the external party answers the call. - Ext 201 transfers the call to Ext 202. Extension-CO duration timer on Ext 202 re-starts when Ext 202 answers the call. Extension-CO duration timer on Ext 201 continues on Ext 202. V1.0 V1.1 Concrete example

ISDN – 3 party Conference DTMF Tone through a Conference from PT Function – Conference ISDN – 3 party Conference DTMF Tone through a Conference from PT

ISDN – 3 Party Conference (EURO-ISDN) -1 Adding a Third Party during a conversation using an ISDN service (Three-party Conference [3PTY] via ISDN) ISDN 1st Party 2nd Party Standard : ETS 300 188 New It is not service item for Euro-ISDN

ISDN – 3 Party Conference (EURO-ISDN) -2 How to establish a conference (During a conversation) PT/PS Press CONF Dial desired phone number ISDN -Hold Talk to the new party 3-party conference Press ISDN-Hold PT/PS Press Transfer Dial desired phone number Talk to the new party Enter Press Transfer 3-party conference Enter

DTMF Tone Through to Conf.Call from PT - This will be useful for two parties to listen to VM message. SLT Voice Mail PT ( Conference ) DTMF Tone Not only SLT user but also PT user can control Voice Mail. Voice Mail control during conference call. SLT PT YES(Can send DTMF) NO(Cannot send DTMF) V1.0 V1.1

Intercept Timer for each time mode Function – Timer Intercept Timer for each time mode

Intercept Timer For Each Time Mode Intercept Timer for Day / Lunch / Break / Night Intercept timer and DISA intercept timer can be programmed for each time service mode. Intercept Timer 1-240 s DISA Intercept Timer 1-60 s : Enable 0 s : Disable

SMDR RC/AN Information Output Paging to Another Paging Group Function – Others SMDR RC/AN Information Output Paging to Another Paging Group

SMDR RC/AN Information Output -1 RC (Receive Call) information, it will be output when TDA receives incoming call. AN (Answer Call) information, it will be output when extension user answered incoming call. Programming is needed. No Print (Default) Print * SMDR Type format is not changed from V1.0 (Type A / B / C). * KX-TD SMDR based application can work. * But some of them can not work properly. Because the detailed Spec. and timing to output is not same as KX-TD series.

SMDR RC/AN Information Output -2 Output Samples-1 - External Call  Extension (201)  No answer  Caller disconnects 20/02/04 07:48AM 201 01 <I>203 RC 20/02/04 07:49AM 201 01 <I>203 0'56 00:00'00 NA - External Call  Extension (201)  Answers  Disconnects 20/02/04 08:22AM 201 01 <I>203 RC 20/02/04 08:22AM 201 01 <I>203 0'11 AN  Ext. 201 Answers 20/02/04 08:22AM 201 01 <I>203 0'11 00:00'17 Output Samples-2 (DISA) - External Call  DISA (270)  OGM is sent  No Answers  Caller disconnects 20/02/04 09:00AM 270 01 <I>203 RC 20/02/04 09:00AM 270 01 <I>203 0'05 AN  DISA Answers 20/02/04 09:01AM 270 01 <I>203 0'05 00:00'19 D0 - External Call  DISA (270)  OGM is sent  Ext. 201 answers  Disconnects 20/02/04 09:04AM 270 01 <I>203 RC 20/02/04 09:04AM 270 01 <I>203 0'05 AN  DISA Answers 20/02/04 09:05AM 270 01 <I>203 0'05 00:00'09 D0  Ext. 201 Answers 20/02/04 09:05AM 201 01 <I>203 0'00 00:00'12 TR

SMDR RC/AN Information Output -3 Output Samples-3 (ICD-G) - External Call  ICD-G (280)  Time table is not started  No Answers  Caller disconnects 20/02/04 08:42AM 280 01 <I>203 RC 20/02/04 08:42AM 280 01 <I>203 0'05 00:00'00 NA - External Call  ICD-G (280)  Time table is not started  Ext.201 Answers  Disconnect 20/02/04 08:49AM 280 01 <I>203 RC 20/02/04 08:49AM 280 01 <I>203 0'04 AN  Ext. 201 Answers 20/02/04 08:49AM 280 01 <I>203 0'04 00:00'00 20/02/04 08:49AM 201 01 <I>203 0'00 00:00'06 - External Call  ICD-G (280)  Time table starts  No Answers  Caller disconnects 20/02/04 10:57PM 280 01 <I>203 RC 20/02/04 10:57PM 280 01 <I>203 0'00 AN  Time table starts 20/02/04 10:57PM 280 01 <I>203 0'00 00:00'17 -External Call  ICD-G (280)  Wait  Time table starts  No Answers  Caller disconnects 20/02/04 08:36AM 280 01 <I>203 RC 20/02/04 08:37AM 280 01 <I>203 0'10 AN  Time table starts 20/02/04 08:37AM 280 01 <I>203 0'10 00:00'19 -External Call  ICD-G (280)  Wait  Time table starts  Ext.201 Answers  Disconnect 20/02/04 10:48PM 280 01 <I>203 RC 20/02/04 10:48PM 280 01 <I>203 0'05 AN  Time table starts 20/02/04 10:48PM 280 01 <I>203 0'05 00:00'12  Ext.201 Answers 20/02/04 10:48PM 201 01 <I>203 0'00 00:00'06

Paging to Another Paging Group - TDA100/200 Ver.1.0 Ext. 201 User Group-01 Ext. 202 User Group-02 Paging Group-01 Ext. 203 User Group-03 Ext. 204 User Group-04 Paging Group-02 NO YES - TDA100/200 Ver.1.1 Ext. 201 User Group-01 Ext. 202 User Group-02 Paging Group-01 Ext. 203 User Group-03 Ext. 204 User Group-04 Paging Group-02 YES No additional programming steps are required. - Operation is not changed from V1.0. ( [*33]+[PageG.Number(2digits)] )

Function – Programming Programmable COS Name & CS Name Ext. CLIP Automatic Generating DDI/DID Name Automatic Generating Wireless XDP Programming from PC

Programmable COS Name & CS Name - TDA100/200 Ver.1.0 - TDA100/200 Ver.1.1 COS name CS name Both 20 Characters

Ext. CLIP Automatic Generating New function 3450155 3450255 3450355 Increase this number Delete digit 201 01 20 => Delete from left 0- 4 1 - 999 Max. 16 digits,( 0 – 9 * # ) CLIP: 345 01 55 1 345 55

DDI/DID Name Automatic Generating New function 12300 12301 12302 12303 PCC00-UK PCC01-UK PCC02-UK PCC03-UK Delete digit 1 - 1000 0 - 32 Max. 20 characters => Delete from left 1 Increase this number 00 20 PCC00-UK 3 PCC -UK

Wireless XDP Programming from PC It is possible to program Wireless XDP connection from the PC maintenance console. - Assign Wireless XDP PS number. - Click “Apply” - Power off-on the Wireless XDP PS for enabling this programming.

Improvement Logical Check PS Hand-over during Conference Call Walking Extension from Fault Extension

Logical Check -1 The following extension assignment logical check function is deleted from the V1.1 PC-Soft. In programming an extension number that does not exist, the system will now accept. 1. System - System Operator PBX-Operator 2. Feature - Tenant Operator 3. Groups - Incoming Call Distribution Group - Group Setting Supervisor Extension 4. Groups - Incoming Call Distribution Group - Member Extension No. 5. Groups - Idle Extension Hunting Group Member Extension 6. Groups - Voice (DTMF) Group - Group Information Extension Number of the SLT Port Connected to VM 7. Extension - Wired Extension/Portable Station - Extension Settings Transfer Recall Destination 8. Optional Device - DISA - Message Setting 1 Digit AA Destination 9. Feature - Speed Dial & Caller ID - Main Table CLI Destination 10. CO & Incoming Call - DIL Table & Port Setting DIL Destination 11. CO & Incoming Call - DDI/DID Table DDI/DID Destination 12. CO & Incoming Call - MSN Table MSN Destination 13. Maintenance - Miscellaneous Local Alarm Display Extension

Logical Check -2 - TDA100/200 Ver.1.0 - TDA100/200 Ver.1.1 What happens? - TDA100/200 Ver.1.0 1- Open the PC maintenance tool and go to 2.System Operator then 2. PBX Operator 2- Click “Apply” Dealer does not know what is wrong! - TDA100/200 Ver.1.1 Please remember, when programming extension numbers that do not exist, that the system will now accept the entry. 1- Open the PC maintenance 2- Go to 2.System Operator 2. PBX Operator 3- Click “Apply” Nothing happens.

Logical Check -3 If we program a non-existing number ?? 1. PBX-Operator OUS mode Extension. 2. Tenant Operator OUS mode Extension. 3. Supervisor Extension No Supervisor Extension 4. ICD Group Member The TDA skips this extension. 5. Idle Extension Hunting Group Member The TDA skips this extension. 6. VM (DTMF) Group VM function does not work. 7. Transfer Recall Destination The transfer recall goes back to the transferring Extension. 8. 1 Digit AA Destination The TDA sends the re-order tone. 9. CLI/DIL/DDI/DID/MSN Destination The TDA checks the following… - Re-order tone - Re-routed to operator 10. Local Alarm Display Extension  No Alarm Extension.

PS Hand-over during Conference Call Handover can be made during Conference Call. Both of 2.4GHz model and DECT model No programming required

Walking Extension from Fault Extension -1 A “Fault” extension card can be used for walking extensions. Insert and remove a card, the non connected extensions can be used for walking extensions. DHLC-8 24 extensions SLC-8 8 extensions DLC-8/SLC16 16 extensions DLC-16 32 extensions

Walking Extension from Fault Extension -2 What is benefit ? One existing extension can be shared to several users with different extension number. Ext 201 Ext 233 Part-time worker - A 8:00-12:00 Ext 234 Part-time worker - B 12:00-16:00 Ext 235 Part-time worker - C 16:00-20:00 Ext 236 Part-time worker - D 20:00-8:00 What is Walking Extension access code? *727 + Extension number + PIN

PC Maintenance Console Compatibility Data Conversion Upgrade PBX To Start TDA100/200 V1.1 PC Maintenance Console Compatibility Data Conversion Upgrade PBX

PC Maintenance Console Compatibility TDA100/200 Ver.1.1 PC maintenance console can maintain TDA100/200 Ver.1.0 PBX, too. Initial screen When we access TDA100/200 Ver.1.0 Automatically

Data Conversion PC maintenance console provides a data convert function. (DSYS Ver.1.0 to DSYS Ver.1.1) 1- Open the PC Maintenance console and open the saved DSYS (Ver 1.0). 3- Enter new file name and click “Save” DSYS 1.0 DSYS-1.1 DSYS 1.1 2- Click

Upgrade PBX 1. Prepare following files 2. Download above files to PBX - PMPR 1.1, DLNG0 1.1, DLNG1 1.1 DSYS 1.1 --- Converted DSYS or New DSYS created by PC-Soft 2. Download above files to PBX 3. Reset PBX by command - V1.0054 or later --- Please select PMPR_SUB, DSYS_SUB, then reset - Before V1.0054 --- Please reset without any care. Select 4.Connect PC-Soft again and download other files as PC-Soft’s dialog box saying. 5.If PC-Soft require reset, reset PBX again, then you can finish upgrading.

Thank you very much !