Rice Cooker Project Integration Phase Integration of Hardware and Software.

Slides:

Advertisements

Similar presentations

Systems Analysis and Design Presented by Thakur Rai.

Advertisements

IGCSE ICT Control Systems.

1 PROJECT MANAGEMENT ROLE OF KEY PERSONNEL Bernd Madauss International Space University Strasbourg February, 2011

1 Lecture 1.4: Life Cycle Models Dr. John MacCarthy UMBC CMSC 615 Fall, 2006.

Software Acquisition Management SAM-450 EXEC SAM Spiral Models and Paradigms SAM Executive Seminar George Prosnik DAU CDSC E&T Center.

SIAP SE TEM ppt-1 IEEE Standard for Application & Management of the Systems Engineering Process Robert L. Hobart Deputy Commander, C4I Integration.

1 Lecture 3.2: Technical Reviews and Audits (SEF Ch 11) Dr. John MacCarthy UMBC CMSC 615 Fall, 2006.

THYRISTORS WHAT ARE THYRISTORS ?.

Software Testing Test Design and Implementation. Agenda Test Design Test Implementation Test Design Sources Automated Testing 2.

Tasks 1.Check you have the following posts: 1.Hardware and Software 2.Input and Output 3.Components of a Computer 2.ALL fonts should be a sensible size.

Effective Methods for Software and Systems Integration

AS ICT.  Have an understanding of how organizations use ICT.  Be able to describe a number of uses, giving the hardware and software requirements. 

Chapter 2: Overview of Essentials ISE 443 / ETM 543 Fall 2013.

Real-Time Software Design Yonsei University 2 nd Semester, 2014 Sanghyun Park.

Twenty Questions Electronics. Twenty Questions

Refined ECSS Software Process Model for Critical SW Critical SW Case Study.

1 Lecture 5.2a: SEF Ch 8 SE Outputs Dr. John MacCarthy UMBC CMSC 615 Fall, 2006.

Systems Development Lifecycle Testing and Documentation.

Configuration Management Non Government Std: EIA Standard-649 “A management process for establishing and maintaining consistency of a product’s performance,

Refined ECSS Software Process Model Elements SD-TN-AI-0570, Issue 5 APPENDIX D.

Escape Systems Mar 01 AIRCREW SYSTEMS ILSMT BRIEFING NACES ADVANCED ELECTRONIC SEQUENCER PROGRAM FUTURE ADVANCED SEQUENCER TECHNOLOGY (FAST)

Robotics & Engineering Design Projective Management Chin-Sung Lin Eleanor Roosevelt High School.

Overview What is Arduino? What is it used for? How to get started Demonstration Questions are welcome at any time.

Lecture Introduction to Software Development SW Engg. Development Process Instructor :Muhammad Janas khan Thursday, September.

DPE CSSW Process Model Annex A WP-400 ECSS Case Study.

COSC 4303 Software Engineering Introduction and Initial Planning of Group Projects Fall 2007.

Twenty Questions Electronics. Twenty Questions

System A collection of parts that perform a function.

Status of the TTCE-EGSE and Power Supply Mauro Menichelli INFN Perugia.

AND Gate Inputs Output Input A (Switch) Input B (Switch) Output Y (Lamp) 0 (Open) 0 (OFF) A B Lamp.

S/W Programming & Languages Chapter 10 Where Your Software Comes From © The McGraw-Hill Companies, Inc., 2000.

Control Output Devices Hyper linking. Back to Input Devices Back to Input Devices What Are Control Output Devices? These are devices that are associated.

E.Sbrissa EP/TA3 - IC ATLAS EDR_MAG Magnet Project Fault analysis, QA & Failure rate.

V-Shaped Software Development Life Cycle Model. Introduction: Variation of water fall model. Same sequence structure as water fall model. Strong emphasis.

May 5, 2004Slide 2 OmnAuto TMS Solution May 5, 2004Slide 3 OmnAuto TMS Dataflow.

Session 2 Dr. Dan C. Surber, ESEP

Supportability Design Considerations

System Engineering Considerations (See Chapters 3 and 9)

Key Management Issues for Software Reviews

DAG CH 3 Figure 11: Weapon System Development Life Cycle

Rekayasa Perangkat Lunak Part-3

DAG CH 3 Figure 17: Weapon System Development Life Cycle

DAG CH 3 Figure 23: Weapon System Development Life Cycle

CHAPTER 2 Testing Throughout the Software Life Cycle

Software Engineering Rekayasa Perangkat Lunak

DAG CH 3 Figure 13: Weapon System Development Life Cycle

DAG CH 3 Figure 19: Weapon System Development Life Cycle

What is Arduino? By James Tedder.

AI1 input2 AI0 input1 DI1 DI2 DI2 DI1.

Gestion de la documentation pendant le cycle de développement

DAG CH 3 Figure 18: Weapon System Development Life Cycle

DAG CH 3 Figure 28: Weapon System Development Life Cycle

Software Development Process

מרעיון למוצר דני חייט.

JC Technology Logic Gates.

DAG CH 3 Figure 15: Weapon System Development Life Cycle

Software Engineering Rekayasa Perangkat Lunak

Input-Output-Process Demo

HART Technologies Process Overview

Input-Output-Process Demo

CS/EE/ME 75(a) Nov. 19, 2018 Today: Prelimnary Design Review Homework.

PSS verification and validation

Machine Protection PLC Based System Verification and Validation Plan

 Is a machine that is able to take information (input), do some work on (process), and to make new information (output) COMPUTER.

DAG CH 3 Figure 21: Weapon System Development Life Cycle

Software Engineering Rekayasa Perangkat Lunak

DAG CH 3 Figure 27: Weapon System Development Life Cycle

DAG CH 3 Figure 22: Weapon System Development Life Cycle

DAG CH 3 Figure 25: Weapon System Development Life Cycle

Presentation transcript:

Rice Cooker Project Integration Phase Integration of Hardware and Software

System Requirements Analysis System Design Software Requirements Analysis Preliminary Design Detailed Design Coding, Unit Testing Component Integration Testing Hardware Development Functional Baseline Allocated Baseline HW CI Testing Software Development SRR SDR SSR PDR CDR TRR System Integration and Testing Development Cycle of Rice Cooker OCD Product Baseline SW CI Testing Component Integration Testing Manufacturing Unit Testing Hardware Requirements Analysis Preliminary Design Detailed Design

Integration of Hardware and Software Temperature sensor Heater Power Switch (ON/OFF) Rice Cooker Software Inputs Outputs Power Cable Rice Cooker Casing Slow

Operation when Switched ‘ON’ When power is switched ON: –Heater is ON –Heater is OFF –Heater is OFF and Cooking light is ON –Heater is OFF and Warming Light is ON –Cooking and Warming Lights are ON –Heater is ON and Cooking and Warming Lights are ON –Fast/Normal/Slow switches read as ON What should be done, in software, to correct these deficiencies ?