Operational Amplifiers

Slides:

Advertisements

Similar presentations

Op-Amps and Saturation. The Inverting Mode Op-Amp + - V1V1 VoVo RfRf R1R1 In theory, the gain of the op-amp is given by R f ÷ R 1. This equation works.

Advertisements

Operational Amplifiers

The Inverting Mode Op-Amp. What is the Inverting Mode ? The op-amp can be connected up in various ways or modes. What it does depends on how it is connected.

1.6 Op-Amp Basics High input impedance Low output impedance Made using difference amplifiers having 2 inputs and at least 1 output 1 Note: Terminals for.

Operational Amplifier

1 Electronic Circuits OP AMPs. 2 Electronic Circuits Operational amplifiers are convenient building blocks that can be used to build amplifiers and filters.

Operational Amplifiers Luke Gibbons CSUS Fall 2006 ME 114.

ECE201 Lect-161 Operational Amplifiers ( ) Dr. Holbert April 3, 2006.

Operational Amplifiers

Introduction to the OP AMP

ECE 201 Circuit Theory I1 Introduction to the Operational Amplifier μA 741 OP AMP.

Operational Amplifiers (Op Amps) Discussion D3.1.

Lecture 91 Loop Analysis (3.2) Circuits with Op-Amps (3.3) Prof. Phillips February 19, 2003.

Op Amps Lecture 30.

1 More on Op Amps Discussion D Ideal Op Amp 1) The open-loop gain, A v, is infinite. 2) The current into the inputs are zero.

Department of Information Engineering357 Feedback Op amp golden rules Approximations: 1.Voltage difference between the two inputs is zero 2.Input draws.

Operational Amplifiers (Op Amps) Discussion D3.1.

Operation Amplifier. Golden Rules of OP Amp 1.i in =0, no current flow into op amp. 2.V + =V - Typically one end of op amp is connected to ground, therefore,

Analogue Electronics II EMT 212/4

1 OPerational AMPlifier OPAMP Bollen. 2 AGENDA Bollen OPAMP COMPONENT Overview Symbol and package Connections Internal Power connections Vcc and Vee examples.

Operational Amplifier

Electronics - Revision 2. In electronics, it is the voltage that is important. Draw voltage time graphs for analogue and digital systems. 3. Draw a block.

What is an Op Amp? Ideal Op Amps Applications Examples Lecture 9. Op Amps I 1.

St Columba’s High School Electricity and Electronics Op-amps.

Operational Amplifier (op-amp) Positive power supply (+12V) Negative power supply (-12V) Inverting input Non-inverting input Non-inverting input (V+)

Fundamentals of Electric Circuit Analysis, by Clayton Paul Copyright 2000 © John Wiley & Sons. Inc. All rights reserved. Figure 4.1 An op-amp schematic:

EE 1270 Introduction to Electric Circuits Suketu Naik 0 EE 1270: Introduction to Electric Circuits Lecture 13: Operational Amplifiers Part 1 Chapter 5.

Operational Amplifier Basics Revision Question 4 An inverting comparator is shown in Figure 4. Calculate the switching threshold voltages and the hysteresis.

Lecture 4: Electrical Circuits

Operational Amplifiers The operational amplifier, also know as an op amp, is essentially a voltage amplifier with an extremely high voltage gain. One of.

Operational Amplifier The operational amplifier circuit first came into existence as a basic building block in analog computers. I t was referred to as.

Operational Amplifiers Op Amps – a useful building block K. El-Ayat 11.

Applications of OP-AMP. Introduction Operational amplifier using IC's is inexpensive, versatile and easy to use. For this reason they are used not only.

OP-AMPs Op Amp is short for operational amplifier. An operational amplifier is modeled as a voltage controlled voltage source. An operational amplifier.

1 CHAPTER 20 OPERATIONAL AMPLIFIERS (OP-AMPS). 2 Introduction to operational amplifiers Symbol and Terminals.

OPERATIONAL AMPLIFIERS + - Presented by D.Satishkumar Asst. Professor, Electrical & Electronics Engineering

مكبر العمليات Operational Amplifier Operational Amplifier and its circuit. Types of op-amp. Application of op- amp. Examples Operational Amplifier.

EE101-Lecture 8 Operational Amplifier Basics of amplifiers EE101 Fall 2012 Lect 8- Kang1 Noninverting amplifier & Inverting amplifier.

Schmitt Trigger Circuits. Op Amps Previously in ET1 we investigated the Operational Amplifier. The Op Amp consisted of V in V out A feedback loop O V.

UOP ECT 246 Week 3 iLab Op - Amps Check this A+ tutorial guideline at For more classes.

Operational amplifier

Figure 5.1 The eight-lead DIP package (top view).

Chapter 5 Operational Amplifier

ECE 1270: Introduction to Electric Circuits

ELG4135: Electronics III (Fall 2005)

Analogue Electronics Circuit II EKT 214/4

Analogue Electronic 2 EMT 212

ECE 1270: Introduction to Electric Circuits

Feedback No feedback : Open loop (used in comparators)

Examples of Negative Feedback Applications: A) Inverting Amplifiers

Operational Amplifiers (Op Amps) in Chemical Instrumentation

Non-linear Op-Amp Circuits Tim. Content 1 Introduction 2 Zero Crossing Detector – 2.1 Non-Inverting Zero Crossing Detector 2.1 Non-Inverting Zero Crossing.

Operational Amplifiers

Department of CNET Electronic Circuit II

The Ideal Op Amp Inverting and non-Inverting configurations

Introduction to the OP AMP

Ch. 5 – Operational Amplifiers

The operational amplifier

Introduction to the OP AMP

The Ideal Op Amp Inverting and non-Inverting configurations

Schmitt Trigger Circuits

Operational Amplifier (Op-Amp)-μA741

Ch. 5 – Operational Amplifiers

Department of CNET Electronic Circuit II

Department of CNET Electronic Circuit II

Department of CNET Electronic Circuit II

Ch. 5 – Operational Amplifiers

Ch. 5 – Operational Amplifiers

Operational Amplifiers

OPERATIONAL AMPLIFIERS

Presentation transcript:

Operational Amplifiers Op-Amps Operational Amplifiers

What is an Op-amp ? An op-amp is a type of amplifier – an operational amplifier. It takes in one or more voltages ( V1 and V2 ) and processes them, giving out another voltage ( Vout ). Depending on how it is connected up, the op-amp seems to carry out mathematical operations such as addition, subtraction etc.

The Op-Amp Symbol +Vs Inverting input - Output Non-inverting input + -Vs The Op-Amp needs a power supply to make it work. This is represented by Vs. The power supply connections are often missed out in diagrams.

Power Supplies for Op-Amps The power supplies used with Op-Amps are a bit unusual. They are set up to have a positive terminal and a negative terminal and a zero volts terminal between the two. The zero volts terminal acts as a reference voltage when making measurements.