#30 Ignition/Starter Switch #54 To Radio Fuse 1 Instrument Power Ignition Coil 87 85 86 30 Red wire with bullet Long black wire with bullet. Wire was.

Slides:



Advertisements
Similar presentations
How to apply a TXV kit to an evaporator coil – Initial installation
Advertisements

ELECTRICAL RECEPTACLES
DS1000B-RM/ DS1500B-RM Battery Replacement Procedure.
How to Make A Telegraph Exploring the Magic of Electricity.
Powerpoint Jeopardy Category 1Category 2Category 3Category 4Category
Judging The Model “A” Area 2 Electrical System
Copyright Carnegie Mellon Robotics Academy all rights reserved Electromechanical Relays.
EE188L EE I Laboratory Lab #2 Resistive Circuits.
Installation. Indoor Unit Installation Typical Installation.
Lock Replacement. Step 1: Cut insulation behind lock mechanism.
GLOBAL LIFT CORP COMMERCIAL SERIES PORTABLE KIT Portable Kit -
Installation Quick Guide AD400 Cylindrical 6/01/13 Doc #
Installation Instructions. Original distributor, coil, and plug wires.
1 STEPMILL 7000 PT ASSEMBLY INSTRUCTIONS PART NUMBER
160 BOOM ELECTICAL INSTALLATION. 160 BOOM CAB INSTALL INVERTER HARDWARE KIT (4) 10-32X3/4 (4) #10 Lock Washers (8) #10 Flat Washers (4) Nuts (2)
ES1000C/1500C Battery Replacement Procedure. 1.Pull off the front panel.
Oil PSI OIL Temp Fuel PSI Tach Water Temp Water PSI 14ga. 7 Wire Harness Key Ignition Start Starboard Engine 14ga Single Wire Fume Det Fume Detector Harness.
Making A Motor Exploring the Magic of Electricity.
Wire bundles connecting to Keyence Sensors (screw plug on other end) Colored Wires from bundles (brown, blue, white are nonfunctional, cap with scotch.
Installation. Indoor Unit Installation Typical Installation.
Electrical Wiring Three-Way Switches. Three-Way Switch.
STARTING SYSTEM.
MC11000 Kit Replacement 1 1. Open the face plate and remove the 2 screws. Remove and discard the original face plate. 3. Remove the 2 white caps on the.
Title: Corvette C5 Column Lock Bypass Originator: John Neese Date: 30 Jan 2005 Revision: Sheet: 1 of 6 Column Lock Bypass.
Lesson 10: Aircraft Electrical Systems
Wiring Schematics 101 Electrical Symbols Supplemental Inflatable Restraint (SIR) or Supplemental Restraint System (SRS) Icon This icon is used to alert.
Vex 1.0 © 2005 Carnegie Mellon Robotics Academy Inc. Electromechanical Relays.
Diagnosis the engine starting system. Diagnosis failures engine starting system Body ground Starter ground Engine ground Body ground BATTERY M CBA Ground.
Lighting and Wiring Services
Procedure of Connecting Coil Unit In series with Capacitor 10 April 14 Product: Fully Automatic Washing Machine.
I.C. ENGINES Practical No: 1 (17 Mar, 2014). Measurement of Cylinder Pressure If your vehicle has been running roughly or losing power, there may be a.
Alloy Safety Interlocking Engine Start Switch – Bob Smith Please use this information and associated photographs in good faith. The Author does not guarantee.
Camera Pieces in Box TV Battery Battery Charger Camera Sun shade.
Please read all the instructions carefully before the installation. Installation shall be carried out by experienced mechanic. Follow the steps in the.
PS500B/800B Battery Replacement Procedure. 1.Remove the two screws at the bottom of the front panel. 2.Push down then remove the front panel.
PS1500B Battery Replacement Procedure. 1.Pull off the front panel.
Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 34 Installing Branch Circuits.
P:\ISO \Work Instructions\Assembly\Options\ARMADILLO SWEEPER OPTIONS\10X ARMADILLO SWEEPER OPTIONS MODEL: KIT-MFG-ENG SHDN DSL M&FS SWA.
LAB #8. Flywheel and Key Insert the flywheel key into the slot on the crankshaft then instert the flywheel.
Dual Sparkle Circuit Green connections are wires – they can be any colour. Make sure all + and - connections match up. Make sure the larger battery terminal.
PS2200B/3000B Battery Replacement Procedure. 1.Disconnect the wire connecting the UPS and the battery pack. 2.Pull off the battery pack front panel.
Easy Reach 7.0 Honda Element Packing List QtyDescriptionPacked 115ft 10ga Red Wire 16ft 10ga Black Wire 140amp Breaker 23/8 Yellow Ring Terminals 25/16.
PHSAUTOMOTIVESALSPHSAUTOMOTIVESALS Electric Cooling Fans.
Twin Spine Installation. Installation of a Twin Spine is very simple and easy. Before you begin, make sure you have a copy of the installation instructions,
WIRE REPAIR. TROUBLESHOOTING STEPS l Confirm the Complaint l Study the electrical schematic l Locate and repair the fault l Test the repair.
AVIVA™ ELECTRIC BIKES VIPER ASSEMBLY INSTRUCTIONS Aviva™ - For A New Way Of Life.
AVIVA™ ELECTRIC BIKES How to Install and care for: AVIVA™ lithium-Ion Battery Aviva™ - For A New Way Of Life.
Installing Branch Circuits Unit #32. What are Wiring Boxes? hold cable or conduit and protect connections attached to building contain all electrical.
To install the four wires from the back of the coil machine, loosen the four knobs. Keep each wire in center under each knob, off to the side will allow.
GENERAL CAUTION TOOLS REQUIRED ASSEMBLY AND INSTALLATION
Installing Branch Circuits
ASSEMBLY/INSTALLATION INSTRUCTIONS ASSEMBLY AND INSTALLATION
CAUTION GENERAL TOOLS REQUIRED ASSEMBLY AND INSTALLATION
Aircraft Electrical Systems
installing electrical system
Easy Reach 7.0 Honda Element 2003
Easy Reach 7.0 Honda Element 2003
Exploring the Magic of Electricity
CAUTION GENERAL TOOLS REQUIRED ASSEMBLY AND INSTALLATION
FIGURE 18-1 A typical solenoid-operated starter.
Assembly instructions for M-K all bolt together hoppercone kit.
Electrical Wiring Single Pole Switches.
Exploring the Magic of Electricity
Replace fan motor MullToa 45 and 60
FIGURE 18-1 A typical solenoid-operated starter.
Which of the following would best describe the situation inside the circle?
Replacing TrueAir Thermostat with Ecobee SI
9 Cranking System Advanced Automotive Electricity and Electronics
Repairing the Electrical Components
Presentation transcript:

#30 Ignition/Starter Switch #54 To Radio Fuse 1 Instrument Power Ignition Coil Red wire with bullet Long black wire with bullet. Wire was removed from #50 of the Ignition/Starter switch. Bullet to bullet splice To solenoid on Starter (#50) To, under the thumb nut holding the Combo Instruments bale to the dash. Bosch Relay #50 # Lift ground strap from the battery. 2.Remove Ignition/Starter switch from dash. 3.Discard locking tab washer. 4.Remove large black wire (#50) from Ignition/Starters switch. 5.Connect the relays long black wire into the switchs hole #50. 6.Insert removed wire (#50) into splice from relay. 7.Push the red wire into the switch #30 terminal. 8. *Land brown ground wire under the thumb nut on the Combo. 9.Mount switch and relay to the dash. 10.Connect the battery's ground. Installation Instructions All #30 terminals are the same points electrically. * The Combo instrument is grounded by the bale cutting into the dash. After connecting the brown ground wire take extra care to tighten both thumb nuts to insure a good ground. Sure Start Relay ki Bullet Type – K series

For the early style Ignition/Starter Switch. Ignition Starter Switch Wire #50 removed from the Ignition/Starter switch. Wire #30 removed from the Ignition/Starter switch. 1.Lift ground strap from the battery. 2.Remove Ignition/Starter switch from dash. 3.Discard locking tab washer. 4.Remove large black wire (#50) from Ignition/Starters switch. 5.Connect the relays long black wire into the switchs hole #50. 6.Insert removed wire (#50) into splice from relay. 7.Remove the #30 red wire from switch, and insert into splice. 8. *Land brown ground wire under the thumb nut on the Combo. 9.Mount switch and relay to the dash. 10.Connect the battery's ground. Installation Instructions * The Combo instrument is grounded by the bale cutting into the dash. After connecting the brown ground wire take extra care to tighten both thumb nuts to insure a good ground. After a couple of weeks, retighten the small screws in the two splices. From fuse block. To starter Larger red wire. Splices Sure Start Relay kit Screw Type – Bosch Series