OD GEAR PITTING IN 12 MTR BUS. OD GEAR PITTING 12 MTR BUS.

Slides:



Advertisements
Similar presentations
1 Steering Going in the right direction. 2 Steering systems Conventional (parallelogram) Rack & Pinion Electronic (new in 2002) steer by wire Audi/Volvo.
Advertisements

ENGINE CONSTRUCTION.
Manitoba School Bus Pre-Trip Inspection
Starting Systems State a major safety precaution when removing or working around a starting motor.
Standard Transmissions
Clutch Replacement & Inspection Be sure to mark the Pressure Plate to Flywheel orientation. Loosen bolts in sequence 1/2 turn at a time to prevent warpage.
Clutch Fundamentals Chapter 69.
Manual Transmissions.
Clutch Automotive clutch is used to connect and disconnect the manual transmission from the engine.
© Unitec New Zealand 1 Faulty Starting System Symptoms No Cranking Slow Cranking Abnormal Noise Overheating of Cables.
Small Engine Parts Four-Cycle
How Differential works
The art of Engineering TURBINE PARTS. The art of Engineering TURBINE PARTS Valve Parts A. Stems, Disc, Seats B. Crosshead Assembly, Crosshead Bushings,
New Mexico FFA Agricultural Mechanics Career Development Event Engine Power.
1 InnoSys Quick Connect End Effecter Service and Maintenance Procedures Nov. 19, 2007 Rev. B.
Valve train inspection Inspect... Cylinder head castings Valves Guides Springs Cam and lifters Rocker arms and push rods Timing chains and gears Copyright.
Mechanical Arrangement
Clutches Auto 3/4 Mr. Saunders GO 12/2001VHS AUTO3 Who needs a clutch?
© 2015 Cengage Learning. All Rights Reserved. May not be scanned, copied, duplicated, or posted to a publicly accessible website, in whole or in part.
STARTING SYSTEM.
New Mexico FFA Agricultural Mechanics Career Development Event Engine Power.
Engine Construction Stationary Parts 2 s/c Slow Speed BEDPLATE LUBE OIL SUMP A FRAME CYLINDER BLOCK JACKET WATER CYLINDER LINER CYLINDER HEAD INTAKE PORTS.
1000A 60Hz Gearbox Grade 3 Incoming Inspection Serial Number: TGW Job Number:A Inspection Date:5/4/11 1.
1000A 60Hz Gearbox Grade 3 Incoming Inspection Serial Number: (BR) TGW Job Number: Inspection Date: 1/14/13 1.
Manual Transmission Components and Operation
Flat Saw Training. Flat Saw Sizes –Low Horsepower Blade diameters range from 8” (200mm) to 18” (450mm) Power ranges from 4 to 25 horsepower.
Common starting system problems. n n In a no-crank problem, the engine crankshaft does NOT rotate properly with the ignition key at start. The most common.
SERVICING CLUTCHES l Chapter 3 l Page 49 l Lab manual l Page 45 l Classroom Manual.
PISTON ENGINE PROPULSION Chapter 1 Mechanical Arrangement 1933 Alvis Engine 2014 Hyundai Engine.
Clutches.
Note location of different length bolts
Differential Casting An epic look into the differential casting By: Scott Loughran.
Clutches Basic purpose Used to disengage engine from input shaft Flywheel –Bolted to crankshaft –Provides surface for clutch disc to work on Clutch disc.
1 InnoSys Quick Connect End Effecter Service and Maintenance Procedures Shreveport Assembly 14 MAY, 2008.
PVWH Pump Presentation. PVWH Pumps n 10 Displacements –. 66 in³/rev –.86 in³/rev –1.35 in³/rev –1.55 in³/rev –2.06 in³/rev –2,83 in³/rev –3,88 in³/rev.
Shore Power Connection Check the connection on the boat Check the breaker on the dock ON OFF.
1 Product Immersion Olathe June FS 4800 Available as a front pivot (Standard) or rear pivot model 900mm (36”) Maximum Blade Capacity 35.7 kW (48.
Engine Technology Engine Diagnostic its requires an understanding of the fundamentals & a systematic approach to determine what the problem is. If the.
Components/purpose (Terminology) Engine Flywheel – keeps the engine running smoothly but also provides a flat smooth surface that the Centre Plate is pushed.
SUMMER INTERNSHIP AT SWARAJ TRACTORS
Model OutlineBodyBody ElectricalEngineChassis Contents Click a Section Tab.
Clutches.
Automatic Transmission Components and Operation
KSRTC CENTRAL WORKS PRESENTED BY GEORGE JOSE 8214.
Air Cleaner.
Fixed Orifice Tube Cycling Clutch System (FOTCC)
Automotive Engines Theory and Servicing
Manual Drivetrains and Axles
Starting System Circuit Operation and Testing
Parts Pinion Drive Gear: transfers power from
Overview of Vehicle.
Manual Drivetrains and Axles
ENGINE MODE CODES.
Manual Drivetrains and Axles
Clutch Fundamentals.
Manual Drivetrains and Axles
Teknik Kendaraan Ringan
Interference and Timing
THEORY OF MACHINE FRICTION CLUTCHES PREPARED BY:-
MAINTENEANCE AND REPAIR OF STARTING SYSTEMS
Korea University of Technology and Education
How Differential works
Maintenance and repair of driveline and related components
Pre – Trip Inspection Training
Transmission of motion and power
Clutches.
Clutches.
Automotive Engines Theory and Servicing
Manual Transmission/ Transaxles
Presentation transcript:

OD GEAR PITTING IN 12 MTR BUS

OD GEAR PITTING 12 MTR BUS

PROPELLER SHAFT CHECK NUT WRONG FITMENT

FRONT HUB BRG CONE ROTATION FA99

SOCKET TYPE DRAGLINK FAILURE IN 12MTR BUS

CLUTCH FINGER WEAR 15 RDC AND RETAINER SPRING CUT

CLUTCH RELEASE BRG HUB DIGGING RDC 15

12MTR BUS 205HP PISTON CRACK WITHIN 1.3 LAC.

PISTON OIL RING FAILURE 205 HP ENG. 12 MTR BUS

UJ CROSS FAILURE IN 3123H

KINGPIN SHIM CUT IN FA90 AND FA99

CROWN PINION PILOT BEARING PITTING AT 1.5 LAC KM.

SINCRO CONE AND RING WEAR FOUND WITHIN 1 LAC. KM IN 3121H MODEL AND 12MTR CRS

MAIN SHAFT BEARING WEAR FOUND WITHIN 1 LAC. KM IN 3121H MODEL AND 12MTR CRS

INPUT SHAFT BEARING WEAR FOUND WITHIN 1 LAC. KM IN 3121H MODEL AND 12MTR CRS

ACCL- PADEL WIRING HARNES LOOSE CONNECTION

FUEL METERING UNIT PIN BACKOUT

24VOLT ECU CONNECTION SUPPLY LINE PIN BACKOUT FROM BATTERY SIDE

LOOSE CONTACT PINS WITH FEMALE CONNECTER

CYLINDER 1 SPECIFIC ERROR : SHOT CIRCUIT LOW SIDE TO HIGH SIDE

MISSING OF DIAGNOSTIC SOCKET AND WATER SEPRETOR SOCKET

3123 VHICLE SPEED SENCER WRONG FITMENT : F INSTAD OF F