INC 111 Basic Circuit Analysis Week 3 Nodal Analysis.

Slides:



Advertisements
Similar presentations
INC 112 Basic Circuit Analysis
Advertisements

Kirchhoff's Rules Continued
DC CIRCUIT ANALYSIS: NODE AND MESH METHOD
Nodes and reference nodes Steps of Nodal Analysis Supernodes Examples Lecture 5. Nodal Analysis 1.
Lecture 6 Nodal Analysis Section Jack Ou, Ph.D.
METHODS OF ANALYSIS Mesh Analysis Nodal analysis.
Lecture 21 EEE 302 Electrical Networks II Dr. Keith E. Holbert Summer 2001.
Chapter 3 Methods of Analysis
METHODS OF ANALYSIS Mesh Analysis Nodal analysis.
Lecture 261 Nodal Analysis. Lecture 262 Example: A Summing Circuit The output voltage V of this circuit is proportional to the sum of the two input currents.
ECE201 Lect-91 Nodal Analysis (3.1) Dr. Holbert February 22, 2006.
Week2bEECS 42, Spring 2005Prof. White Find i 2, i 1 and i o Circuit w/ Dependent Source Example.
Lecture 4, Slide 1EE 40 Fall 2004Prof. White Lecture #4 OUTLINE Resistors in series –equivalent resistance –voltage-divider circuit –measuring current.
Methods of Analysis PSUT 1 Basic Nodal and Mesh Analysis Al-Qaralleh.
Systematic Circuit Analysis Nodal Analysis Chapter 4 Section 1.
Lect4EEE 2021 Nodal Analysis Dr. Holbert January 28, 2008.
Lecture 271 More Nodal Analysis. Lecture 272 Where We Are Nodal analysis is a technique that allows us to analyze more complicated circuits than those.
EET Survey of Electronics Chapter 14 - Series-parallel circuits.
SUMMARY ON NODAL AND MESH ANALYSIS. Both techniques provide systematic steps in solving electric circuit Nodal applicable to all circuits, Mesh only applicable.
S.Norr - UMD - Fall, 2005 ECE 2006 Lecture for Chapter 4 S.Norr.
Copyright © 2013 The McGraw-Hill Companies, Inc. Permission required for reproduction or display. 1 Chapter 4 Basic Nodal and Mesh Analysis.
Methods of Analysis Eastern Mediterranean University 1 Methods of Analysis Mustafa Kemal Uyguroğlu.
Objective of Lecture Describe what a single node, a distributed node, branch, and loop are. Chapter 2.3 Explain the differences between a series and parallel.
AC and DC meters.
Verification of OHM’s law By: Engr.Irshad Rahim Memon.
NODAL AND LOOP ANALYSIS TECHNIQUES
Methods of Analysis Instructor: Chia-Ming Tsai Electronics Engineering National Chiao Tung University Hsinchu, Taiwan, R.O.C.
EENG 2610: Circuit Analysis Class 4: Nodal Analysis
METHODS OF CIRCUIT ANALYSIS
1 ENGG 1015 Tutorial Circuit Analysis 5 Nov Learning Objectives  Analysis circuits through circuit laws (Ohm’s Law, KCL and KVL) News  HW1 deadline (5.
3.1. Introduction Step to analyze AC Circuits: 1.Transform the circuit to the phasor or frequency domain. 2.Solve the problem using circuit techniques.
Methods of Analysis Chapter 3. Introduction We are now prepared to apply Ohm’s law and Kirchhoff’s laws to develop two powerful techniques for circuit.
ELECTRIC CIRCUITS ECSE-2010 Spring 2003 Class 3. ASSIGNMENTS DUE Today (Thursday): Will introduce PSpice Activity 3-1 (In Class) using PSpice Will do.
INC 112 Basic Circuit Analysis Week 2 Kirchhoff's laws.
IEEE’s Hands on Practical Electronics (HOPE) Lesson 3: Ohm’s Law, Equivalent Resistances.
Study Guide Exam 1. Closed book/Closed notes Bring a calculator Format – 6 short answer questions 3 questions on material from HW questions related.
Chapter 19 DC Circuits. Objective of the Lecture Explain Kirchhoff’s Current and Voltage Laws. Demonstrate how these laws can be used to find currents.
Lecture 8 Review: Mesh Analysis Related educational materials:
1 18 Overview resistor & capacitor circuits Kirchoff’s Rules voltmeters & ammeters household circuits & safety Homework: 17, 27, 31, 33, 55, 67, 71, 85.
J. Gabrielse Ohm’s law V I R. J. Gabrielse Voltage (V) Definition: what pushes charges Unit: volt (V) Measured by putting voltmeter in parallel. -+
Chapter 8 – Methods of Analysis Lecture 10 by Moeen Ghiyas 05/12/
Chapter 2 Fundamentals of Electric Circuits Tai-Cheng Lee Electrical Engineering/GIEE 1.
Engineering Fundamentals and Problem Solving, 6e Chapter 17 Electrical Circuits.
Previous Lecture 7 (Problems Solving)
Concepts of Engineering and Technology Basic Electricity and Electronics: DC Circuits Copyright © Texas Education Agency, All rights reserved. 1.
Ch 3: Methods of Analysis
INC 111 Basic Circuit Analysis
Lecture 4, Slide 1EECS40, Spring 2004Prof. Sanders Lecture #4 OUTLINE Resistors in series –equivalent resistance –voltage-divider circuit –measuring current.
ECE201 Lect-151 Nodal Analysis (7.8) Dr. Stephen Goodnick October 3, 2003.
Techniques of Circuit Analysis 1 Electrical Circuits CEN270.
Nodal Analysis From :- Varia Hardik –
Fakulti Kejuruteraan Elektrik
It’s Time For... Circuit Jeopardy!.
Generating Circuit Equations
Internal Resistance in EMF
Introducing Supernodes!!!
INC 112 Basic Circuit Analysis
Nodes, Branches, and Loops
Nodes, Branches, and Loops
Current Directions and
Alexander-Sadiku Fundamentals of Electric Circuits
INC 111 Basic Circuit Analysis
Lecture 01 - Node Voltage Analysis
Nodal and Mesh Analysis
Node-Voltage Method Identify the nodes
Basic Electrical Measurements
Node - Voltage Method ECE 201 Circuit Theory I.
Circuit w/ Dependent Source Example
طرق تحليل الدوائر الكهربائية
Chapter 3 – Methods of Analysis
Presentation transcript:

INC 111 Basic Circuit Analysis Week 3 Nodal Analysis

Systematic Methods for Analyzing a Circuit Nodal Analysis Mesh Analysis (Loop analysis)

Node Node = Point that connected together on the same wire V Example 3 nodes

Nodal Analysis Procedure 1. Count the number of nodes = N 2. Choose one of the nodes to be a reference node (0V) when there is no ground 3. Give the voltage for other nodes to be V1, V2, V3, … 4. Use Kirchoff’s current law on each node to form N-1 equations 5. Solve the equations to find V1, V2, V3, …

Example 0V (reference) V1 V2

0V (reference) V1 V2 Equation 1

0V (reference) V1 V2 Equation 2

Solve the Equations V1 V2 V1 = 5 V V2 = 2.5V

Example V1 V2 V3 0V

V1 V2 V3 0V Equation 1

V1 V2 V3 0V Equation 2

V1 V2 V3 0V Equation 3

Solve the Equations

Cramer’s Rule (Optional)

Supernode When there is a voltage source in the circuit, direct KCL cannot be used because we do not know the current in the voltage source. We will use the idea of supernode. Supernode is the method that combines 2 nodes together when using KCL. It will include the voltage source within the circle when using KCL.

Example V1 V2 V3 0V

V1 V2 V3 0V Equation 1

V1 V2 V3 0V Equation 2 supernode Equation 3

V1 = V V2 = V V3 = V

Example 0V V1 V2

Sanwa YX360TRF Multimeter

Range Selector DialResistance Zero Adjust

Resistance Measurement Read this Range Select these ranges

Voltage Measurement Read this Range Select these ranges

Current Measurement Read this Range Select these ranges

Measure the Resistance of Ammeter and Voltmeter Adjust a multimeter to measure volt and use another multimeter to measure its resistance. Adjust a multimeter to measure amp and use another multimeter to measure its resistance.

Resistor Code

Standard Resistor Value 1R010R100R1K010K100K1M010M 1R212R120R1K212K120K1M2n/a 1R515R150R1K515K150K1M5n/a 1R818R180R1K818K180K1M8n/a 2R222R220R2K222K220K2M2n/a 2R727R270R2K727K270K2M7n/a 3R333R330R3K333K330K3M3n/a 3R939R390R3K939K390K3M9n/a 4R747R470R4K747K470K4M7n/a 5R656R560R5K656K560K5M6n/a 6R868R680R6K868K680K6M8n/a 8R282R820R8K282K820K8M2n/a E12 -Standard

Protoboard

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.