MEYRA CAN

MEYRA CAN remote module identical remotebox for many wheelchair models   identical remotebox for many wheelchair models mechanically reinforced joystick with build in „dead-man-system“ spray water protected housing sensible keypad, visible feedback for lights digital tachometer: speed, resettable day trip counter, distance counter locking function operated by magnetic key integrated charging socket and horn additional connectors for external ON/OFF key, external keypad, external joystick / special controls / PC link

safety: MEYRA‘s „dead-man-system“ MEYRA CAN safety: MEYRA‘s „dead-man-system“

remote module : connectors MEYRA CAN remote module : connectors connector / PIN/ comment X1 1 GND  2 external ON/OFF, momentary switch X2 1 GND  2 external keypad Service 1 5V_EXTERN, ext. supply, max. 20 mA  2 EXT_JOY_X, speed signal of ext. joystick  3 EXT_JOY_Y, direction signal of ext. joystick  4 GND  5 ext. ON/OFF, momentary switch  6 EXT_JOY_CENTER, centre detect signal  7 EXT_RS232_TXD, serial data (TTL)  8 EXT_RS232_RXD, serial data (TTL) BUS 1 Bus supply +24V, max. 5A  2 Bus supply +24V, max. 5A   3 Bus supply +24V, max. 5A 4 Bus supply GND, max. 5A  5 Bus supply GND, max. 5A  6 Bus supply GND, max. 5A  7 Bus signal CAN_HIGH  8 Bus signal CAN_LOW   9 Bus signal BUS_ON  10 Bus signal DMS_LINE

MEYRA CAN power module PM 1: transaxle version for OPTIMUS2 / TOURING 928 (24V, 1 x 110A/180A + 1 x 6A ) PM 2: two-motor-drive version for SPRINT GT 3.593 (24V, 2 x 90A)   robust & easy to service: lights module included, addtional power horn or brake light ( programmable ) build in red and green state indicator input and output lines short circuit protected with automatic restart, no fuses required easy to service by detachable connectors housing spray water protected

Power module „PM1“ and „PM2“ : connectors MEYRA CAN Power module „PM1“ and „PM2“ : connectors X1: battery X2, X4: drive motor, safety brake ( PM2: left motor ) X3, X5: drive motor2, safety brake2 ( only PM2: right motor ) X6: steering servo motor ( only PM1 ) X7, X8, X9, X10: vehicle lights X11: speed-o-meter X12, X13: freewheel switches : drive system and parking brake X14: speed reduction or forward/backward switch X15: optional : powerful horn or brake light X16. X17: bus connector X18: optional power supply output 24VDC

MEYRA CAN actuator module 2 actuator modules: 4 motors (VM1)   2 actuator modules: 4 motors (VM1) 6 motors (VM2)   output current (0 ... 10A) and output voltage (12V or 24V) programmable 12V actuators applicable ("RECARO" – seat )   motor soft start, operation by keypad or joystick(s)   build in red and green state indicator   all connectors detachable

actuator module : connectors MEYRA CAN actuator module : connectors actuator 1: left legrest actuator 2: right legrest actuator 3: seat angle actuator 4: backrest angle actuator 5: seat lift ( SPRINT GT 3.593 or CHAMP 1.594) actuator 6: optional actuator X1, X2, X3, X4, XX: end stop switches

standards & requirements MEYRA CAN standards & requirements ·         general requirements EN12182 EN12184 ·         requirement for biocompatibility EN30993          mechanical strenght ISO7176/8          environmental protection ISO7176/9          electrical safety ISO7176/14          EME-emission ( 30MHz...1GHz, class “B” ) EN55022          EMS-susceptibility ( >12V/m, 1kHz, 80% modulation ) IEC1000-4-3          ESD-protection ( >8kV air discharge ) IEC1000-4-2 ·         documentation and labels prEN1041 ISO7176/15

Control panel & program label MEYRA CAN Control panel & program label ·        

“ON-BOARD“ - programming MEYRA CAN “ON-BOARD“ - programming wheelchair is “ ON “ and the display shows “ 0.0 “ Push keys on the right and on the bottom and keep them pressed Push left key and release it Controller powers down: “OFF “ Release right and bottom keys Push left key and release Wheelchair is “ ON “ and display shows “ HHH “ Back to drive mode by steps 2.) ... 6.) ·         3. 2. 2.

“ON-BOARD“ - programming MEYRA CAN “ON-BOARD“ - programming Joystick – Priority   drive parameters wheelchair - type   Speed-o-meter F – H mode   user profile select

parameter select in user profiles MEYRA CAN parameter select in user profiles Factory preset  Profile select down   Profile select up decrease value   increase value  Next parameter

programmable parameter MEYRA CAN programmable parameter ·        

select joystick - priority MEYRA CAN select joystick - priority operate key and release display shows “ JP0 “ move joystick with highest priority ( e.g. attendant joystick ) display changes to “ JP1 “ move joystick with lower priority display changes to “ JP2 “ display shows “HHH“ again Only the selected joysticks are enabled ! ·        

select wheelchair type MEYRA CAN select wheelchair type operate key and release display shows selected type ( or „000“ for spare part ! ) select by “  “ or “  “ required wheelchair type according tables ( e.g. „12“ for TOURING 928 10km/h ) display shows “HHH“ again

Select wheelchair type MEYRA CAN Select wheelchair type

Select wheelchair type MEYRA CAN Select wheelchair type

MEYRA CAN select wheel diameter operate key and release display shows selected wheel diameter in cm select diameter by “  “ or “  “ OPTIMUS 3.622 : front wheel OPTIMUS2 2.322 : back wheel SPRINT GT 3.593 : back wheel TOURING 927 : front wheel TOURING 928 : back wheel display shows “HHH“ again ·        

MEYRA CAN PC-Mouse / BLUETOOTH Move to „BLU“ menu by pressing ‚mode‘ key when BLUETOOTH module Code 809 ) is connected Move mouse pointer by moving internal or external joystick ( chin control !) Left and right mouse button is active by „left indicator“ and „right indicator“ key or: keys on external keyboard or: digital mini joystick Double click „left“ and „right“ possible „Drag and Drop“ by „left“ and „right“ mouse button ·