Motor Propeller wrench Screw Nut (2) Cylinder top Tiny screw IGNORE:

Slides:

Advertisements

Similar presentations

Brake System Diagnosis and Repair

Advertisements

How to center the top roller Current Situation The slider is not centered because the bottom slider was not placed at 6 o’clock ?!

Instructions for making plunger fork tool. Drawing for the trigger assembly.

Copyright © Texas Education Agency, All rights reserved. Flexible Manufacturing Precision Machining Safety 1.

Tools and Fasteners And, Their Uses.

Optical Manufacturing Solutions 1 Probe Assembly.

Motor & Encoder Mounting Guide. Bill of Materials 1. 10:1 Micro Metal Gearmotor HP item # 999 X 2 2. Pololu Micro Metal Gearmotor Bracket Extended Pair.

Lock Replacement. Step 1: Cut insulation behind lock mechanism.

Click on this image to open the full PDF document.

GLOBAL LIFT CORP COMMERCIAL SERIES PORTABLE KIT Portable Kit -

C-Base Transmission Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team

1 STEPMILL 7000 PT ASSEMBLY INSTRUCTIONS PART NUMBER

Honda Recon TRX-250 Installation Manual. STEP 1: Remove rear tires and install axle spacers. Use blue thread locker and tighten lugs to ATV specification:

Electrical Wiring Circuit Board Project. STEP 1 - Identify all Parts of the Project Saw Drill Driver w/ bits Drill w/bits (not pictured) #2 Phillips Screwdriver.

860 (LF), 880 ½”- 2” 860 (LF), 880 ½”- 2”. Modification Overview  Production of the ½ - 2” 860 series began in 1997 and is current.  The 880 is an “N”

Air tank installation instructions Included parts: Raw aluminum air tank bracket 5/16-18 button head bolts (qty 4) M8x1.25 button head bolts (qty 4) M8.

Vent window installed. Install door frame side latch.

L.C. Technology ROBOT ASSEMBLY. Base Assembly BASE File off raised tabs on each side of Servo. Place Servo in vice between Fibre Clamps. Raised Tabs Repeat.

Handy Store Fixtures Gondola Dolly Assembly Instructions

Wheel Bearing Service. - Remove the cap using a flat head screw driver or pipe pliers. Careful not to damage the cap.

Bob Howard 10/22/2011.  How many connectors do you need ◦ Max DC/Servo Motor Controllers is 4 so use 4  How long should the connectors be ◦

LAUNCHER BASE PARTS B A D E F C G. LAUNCHER BASE PARTS B A D E F C G.

CHAPTER 33 Drum Brake Systems.

Learning Objectives To be able to state the different safety precautions associated with the lathe. To be able to identify and state the function of the.

1. b. Rip Saw 2. d. Used for cutting with the grain.

Robotics – 8. Plates (2-sizes) Plate with holes on 0.500" increments and 1/8" diamonds in between. Can be cut on 0.500" increments. Available in two sizes.

Peregrine the Martian Lander Assembly Instructions Mission to Mars 2008.

Hand Tools, Fasteners, and Hardware

1.a. Item has external threads Go to 2 (screws) b. Item has no external threads Go to 7Go to 2 Go to 7.

48 hour tool Step by Step.

Installing a single Dreamscreen Set unit in place and attach with 2 ½ “ screw. Do not tighten the screw yet, tighten just enough to keep from falling.

Clarinet Assembly Best assembly to prevent unnecessary repairs.

How to move your horn.. 1.This one is a shot of the horn with the acorn nut removed. STEP 1.

Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set screw throught the hole in the yellow part 2 Note: there.

XR621 Drive Hose Update Kit. Removal Turn off Battery dis Drain hydraulic tank Remove both rubber lines under chassis and discard. Remove and discard.

Motor Propeller wrench Screw Nut (2) Cylinder top Tiny screw IGNORE:

Tire Rotation Tire rotation extends the life of your tires.extends the life of your tires In most cases tires should be rotated every 6000 miles (10,000.

AVIVA™ ELECTRIC BIKES VIPER ASSEMBLY INSTRUCTIONS Aviva™ - For A New Way Of Life.

1 Equilibrium The Balancing Robot By: Kerry Scharfglass Whiz Kid.

Description of Hand Tools Tools help us do work and make things. Tools.

Section 2 Safety, Tools and Equipment, Shop Practices Unit 6: Fasteners.

Build A Motor You must follow the directions step-by-step!

 A car Jack  A wrench  A flat surface Put the car into park and apply the parking brake.

Assembly of steering.

VIEW SERIES with Sliding Door

Common Woodworking Hand Tools

What is TETRIX? If you can dream up a robot design, you can build it with the TETRIX Robotics Design System.

STEP 1: ASSEMBLE ANGLE PLATES

Rear end assembly.

Vertical Mill Basics Instructor:.

Annex 4 - Moving Frame and Whiffletree assembly

Flexible Manufacturing

Deconstructing a Hubsan and Rebuilding

Electrical Wiring Circuit Board Project

SeaPerch Structural System

SeaPerch Structural System

Bilge Pump Service Project Model Service Kit

Building and Shrouding Motors.

Tether Management.

Mounting Servos and Black Gear Motors in Botball Robots

STEP 1: ASSEMBLE ANGLE PLATES

Teacher training resource: Robotic Assembly

Most Effective Procedures to Repair a Brake Booster.

Activity 2.2.1a Action Reaction Construction Guide

SeaPerch Structural System

W201 3R hardboard Replacement Procedure.

Drawing of stud.

SeaPerch Structural System

BUILDING AN AUTONOMOUS QUADCOPTER.

Presentation transcript:

Motor Propeller wrench Screw Nut (2) Cylinder top Tiny screw IGNORE:

Place the propeller on the screw Tighten a nut behind it Tighten another nut midway up the screw

Using small pliers, remove the cap from the motor

Place cylinder top on motor Make sure hole is directed at the flat side Place screw on wrench Screw into cylinder top

Tighten screw into cylinder top Tighten nut onto cylinder top **When finished with propeller, use lock- tight glue to secure nuts and propeller. DO NOT use lock-tight glue if you plan to rebuild propellers with students.

Use specialized pieces as propeller mounts!

How will propeller placement effect speed/maneuverability? Where on the ROV? Close together? Far apart? In frame? Out of frame? Think about morning activity

What are your ideas?