Electronic Instrumentation Experiment 5 * Part A: Bridge Circuits * Part B: Potentiometers and Strain Gauges * Part C: Oscillation of an Instrumented Beam.

Slides:



Advertisements
Similar presentations
Chapter 7.
Advertisements

Series-Parallel Circuits
RLC circuits - Part 2 Resonance/Notches/Bandpass Cartoon from Agilent,
Adapted from Holt book on physics
Let us examine this LC circuit mathematically. To do this let us examine the energy of the system. Conservation of Energy 2 nd order differential equation.
Alternating Current Circuits
Electronic Instrumentation Experiment 4 * Part A: Bridge Circuits * Part B: Potentiometers and Strain Gauges * Part C: Oscillation of an Instrumented Beam.
Electronic Instrumentation Experiment 3 * Part A: Instrumented Beam as a Harmonic Oscillator * Part B: RC and RLC Circuits – Examples of AC Circuits.
1 Thevenin Voltage Equivalents w Thevenin invented a model called a Thevenin Source for representing a complex circuit using A single “pseudo” source A.
AC Review Discussion D12.2. Passive Circuit Elements i i i + -
1 Sinusoidal Functions, Complex Numbers, and Phasors Discussion D14.2 Sections 4-2, 4-3 Appendix A.
CHAPTER 5 DC AND AC BRIDGES.
electronics fundamentals
Electronic Instrumentation Experiment 5 Part A: Bridge Circuit Basics Part B: Analysis using Thevenin Equivalent Part C: Potentiometers and Strain Gauges.
بسم الله الرحمن الرحيم FCI.
Series RLC Network. Objective of Lecture Derive the equations that relate the voltages across a resistor, an inductor, and a capacitor in series as: the.
Source-Free RLC Circuit
Spring Forces and Simple Harmonic Motion
Oscillation.
10/17/2013PHY 113 C Fall Lecture 151 PHY 113 A General Physics I 11 AM – 12:15 PM TR Olin 101 Plan for Lecture 15: Chapter 15 – Simple harmonic.
Dynamic Presentation of Key Concepts Module 2 – Part 3 Meters Filename: DPKC_Mod02_Part03.ppt.
Chapter 15 Oscillatory Motion.
1 W12D2 RC, LR, and Undriven RLC Circuits; Experiment 4 Today’s Reading Course Notes: Sections , 11.10, ; Expt. 4: Undriven RLC Circuits.
1 Unit Eight: Thevenin’s Theorem Maximimum Power Transfer Theorm John Elberfeld ET115 DC Electronics.
Alternating Current Circuits
Chapter 32 Inductance. Joseph Henry 1797 – 1878 American physicist First director of the Smithsonian Improved design of electromagnet Constructed one.
ES250: Electrical Science
Preview Objectives Schematic Diagrams Electric Circuits Chapter 18 Section 1 Schematic Diagrams and Circuits.
electronics fundamentals
Review Part 3 of Course. Passive Circuit Elements i i i + -
Lesson#23 Topic: Simple Circuits Objectives: (After this class I will be able to) 1. Explain the difference between wiring light bulbs in series and in.
Class 34 Today we will: learn about inductors and inductance
DC Circuits Muhajir Ab. Rahim School of Mechatronic Engineering Universiti Malaysia Perlis.
P Class 26: Outline Hour 1: Driven Harmonic Motion (RLC) Hour 2: Experiment 11: Driven RLC Circuit.
The V  I Relationship for a Resistor Let the current through the resistor be a sinusoidal given as Is also sinusoidal with amplitude amplitudeAnd.
Chapter 14 VIBRATIONS AND WAVES In this chapter you will:  Examine vibrational motion and learn how it relates to waves.  Determine how waves transfer.
L C LC Circuits 0 0 t V V C L t t U B U E Today... Oscillating voltage and current Transformers Qualitative descriptions: LC circuits (ideal inductor)
Periodic Motion Motion that repeats itself over a fixed and reproducible period of time is called periodic motion. The revolution of a planet about its.
09/16/2010© 2010 NTUST Chapter 6 Yu-Chi Lai 賴祐吉. 09/16/2010© 2010 NTUST Most practical circuits have combinations of series and parallel components. Components.
Chapter 6 Series and Parallel Circuits 1 of 81 MECH of 81 Chapter 6 Series and Parallel Circuits MECH1100 Topics Identifying Series- Parallel Relationships.
Periodic Motion What is periodic motion?
Lecture 3: Bridge Circuits
Phasors and Kirchhoff’s Current Law
Self Inductance Consider a solenoid L, connect it to a battery Area A, length  l, N turns What happens as you close the switch? Lenz’s law – loop resists.
A sinusoidal current source (independent or dependent) produces a current That varies sinusoidally with time.
Lecture - 7 First order circuits. Outline First order circuits. The Natural Response of an RL Circuit. The Natural Response of an RC Circuit. The Step.
Chapter 19 Principles of Electric Circuits, Conventional Flow, 9 th ed. Floyd © 2010 Pearson Higher Education, Upper Saddle River, NJ All Rights.
Chapter 6 Series-Parallel Circuits. Objectives Identify series-parallel relationships Analyze series-parallel circuits Analyze loaded voltage dividers.
1 Driven Oscillations Driven Oscillators –Equation of motion –Algebraic solution –Complex algebra solution Phase and amplitude of particular solution –Algebraic.
Network Theorems Topics Covered in Chapter 8 8-1: Kirchhoff’s Current Law (KCL) 8-2: Kirchhoff’s Voltage Law (KVL) 8-3: Superposition Theorem 8-4: Thevenin’s.
CHAPTER 5 DC AND AC BRIDGES.
1 10. Harmonic oscillator Simple harmonic motion Harmonic oscillator is an example of periodic motion, where the displacement of a particle from.
PHY 151: Lecture Motion of an Object attached to a Spring 12.2 Particle in Simple Harmonic Motion 12.3 Energy of the Simple Harmonic Oscillator.
The Wheatstone Bridge Using Kirchhoff’s Voltage Law:
Electronic Circuit CH. 1 Dept. of Electrical and Electronic Engineering Chang Bum, Lee Office: 1315 (055)
SCHOOL OF ENGINEERING Introduction to Electrical and Electronic Engineering Part 2 Pr. Nazim Mir-Nasiri and Pr. Alexander Ruderman.
Topics Identifying Series- Parallel Relationships
EGR 2201 Unit 6 Theorems: Thevenin’s, Norton’s, Maximum Power Transfer
Chapter 7.
TOPIC 3: FREQUENCY SELECTIVE CIRCUITS
Sinusoidal Functions, Complex Numbers, and Phasors
Electric Circuits Fundamentals
BASIC ELECTRICAL ENGINEERING
2. 2 The V-I Relationship for a Resistor Let the current through the resistor be a sinusoidal given as Is also sinusoidal with amplitude amplitude.
The Theorems we will look at are:
Chapter 7.
Mechatronics Engineering
Chapter 8.
Apply KCL to the top node ,we have We normalize the highest derivative by dividing by C , we get Since the highest derivative in the equation is.
Series-Parallel Circuits
Presentation transcript:

Electronic Instrumentation Experiment 5 * Part A: Bridge Circuits * Part B: Potentiometers and Strain Gauges * Part C: Oscillation of an Instrumented Beam * Part D: Oscillating Circuits

Part A w Bridges w Thevenin Equivalent Circuits

Wheatstone Bridge A bridge is just two voltage dividers in parallel. The output is the difference between the two dividers.

A Balanced Bridge Circuit

Thevenin Voltage Equivalents w In order to better understand how bridges work, it is useful to understand how to create Thevenin Equivalents of circuits. w Thevenin invented a model called a Thevenin Source for representing a complex circuit using A single “pseudo” source, Vth A single “pseudo” resistance, Rth   

Thevenin Voltage Equivalents This model can be used interchangeably with the original (more complex) circuit when doing analysis. The Thevenin source, “looks” to the load on the circuit like the actual complex combination of resistances and sources.

The Battery Model w Recall that we measured the internal resistance of a battery. w This is actually the Thevenin equivalent model for the battery. w The actual battery is more complicated – including chemistry, aging, …

Thevenin Model Load Resistor Any linear circuit connected to a load can be modeled as a Thevenin equivalent voltage source and a Thevenin equivalent impedance.

Note: w We might also see a circuit with no load resistor, like this voltage divider.

Thevenin Method w Find Vth (open circuit voltage) Remove load if there is one so that load is open Find voltage across the open load w Find Rth (Thevenin resistance) Set voltage sources to zero (current sources to open) – in effect, shut off the sources Find equivalent resistance from A to B A B

Example: The Bridge Circuit w We can remodel a bridge as a Thevenin Voltage source    

Find Vth by removing the Load AABB Let Vo=12, R1=2k, R2=4k, R3=3k, R4=1k

To find Rth w First, short out the voltage source (turn it off) & redraw the circuit for clarity. AB A B

Find Rth w Find the parallel combinations of R1 & R2 and R3 & R4. w Then find the series combination of the results.

Redraw Circuit as a Thevenin Source w Then add any load and treat it as a voltage divider.

Thevenin Method Tricks w Note When a short goes across a resistor, that resistor is replaced by a short. When a resistor connects to nothing, there will be no current through it and, thus, no voltage across it.

Thevenin Applet (see webpage) w Test your Thevenin skills using this applet from the links for Exp 3

Does this really work? w To confirm that the Thevenin method works, add a load and check the voltage across and current through the load to see that the answers agree whether the original circuit is used or its Thevenin equivalent. w If you know the Thevenin equivalent, the circuit analysis becomes much simpler.

Thevenin Method Example w Checking the answer with PSpice w Note the identical voltages across the load = 4.1 (only two significant digits in Rth)

Thevenin’s method is extremely useful and is an important topic. w But back to bridge circuits – for a balanced bridge circuit, the Thevenin equivalent voltage is zero. w An unbalanced bridge is of interest. You can also do this using Thevenin’s method. w Why are we interested in the bridge circuit?

Wheatstone Bridge Start with R1=R4=R2=R3 V out =0 If one R changes, even a small amount, V out ≠0 It is easy to measure this change. Strain gauges look like resistors and the resistance changes with the strain The change is very small.

Using a parameter sweep to look at bridge circuits. PSpice allows you to run simulations with several values for a component. In this case we will “sweep” the value of R4 over a range of resistances. This is the “PARAM” part Name the variable that will be changed

Parameter Sweep w Set up the values to use. w In this case, simulations will be done for 11 values for Rvar.

Parameter Sweep w All 11 simulations can be displayed w Right click on one trace and select “information” to know which Rvar is shown.

Part B w Strain Gauges w The Cantilever Beam w Damped Sinusoids

Strain Gauges When the length of the traces changes, the resistance changes. It is a small change of resistance so we use bridge circuits to measure the change. The change of the length is the strain. If attached tightly to a surface, the strain of the gauge is equal to the strain of the surface. We use the change of resistance to measure the strain of the beam.

Strain Gauge in a Bridge Circuit

Cantilever Beam The beam has two strain gauges, one on the top of the beam and one on the bottom. The stain is approximately equal and opposite for the two gauges. In this experiment, we will hook up the strain gauges in a bridge circuit to observe the oscillations of the beam.

Modeling Damped Oscillations w v(t) = A sin(ωt)

Modeling Damped Oscillations w v(t) = Be -αt

Modeling Damped Oscillations w v(t) = A sin(ωt) Be -αt = Ce -αt sin(ωt)

Finding the Damping Constant w Choose two maxima at extreme ends of the decay.

Finding the Damping Constant w Assume (t0,v0) is the starting point for the decay. w The amplitude at this point,v0, is C. w v(t) = Ce -αt sin(ωt) at (t1,v1): v1 = v0e -α(t1-t0) sin(π/2) = v0e -α(t1-t0) w Substitute and solve for α: v1 = v0e -α(t1-t0)

Part C w Harmonic Oscillators w Analysis of Cantilever Beam Frequency Measurements

Examples of Harmonic Oscillators w Spring-mass combination w Violin string w Wind instrument w Clock pendulum w Playground swing w LC or RLC circuits w Others?

Harmonic Oscillator w Equation w Solution x = Asin(ωt) w x is the displacement of the oscillator while A is the amplitude of the displacement

Spring w Spring Force F = ma = -kx w Oscillation Frequency w This expression for frequency holds for a massless spring with a mass at the end, as shown in the diagram.

Spring Model for the Cantilever Beam w Where l is the length, t is the thickness, w is the width, and m beam is the mass of the beam. Where m weight is the applied mass and a is the length to the location of the applied mass.

Finding Young’s Modulus w For a beam loaded with a mass at the end, a is equal to l. For this case: where E is Young’s Modulus of the beam. w See experiment handout for details on the derivation of the above equation. w If we can determine the spring constant, k, and we know the dimensions of our beam, we can calculate E and find out what the beam is made of.

Finding k using the frequency w Now we can apply the expression for the ideal spring mass frequency to the beam. w The frequency, f n, will change depending upon how much mass, m n, you add to the end of the beam.

Our Experiment w For our beam, we must deal with the beam mass and any extra load we add to the beam to observe how its performance depends on load conditions. w Real beams have finite mass distributed along the length of the beam. We will model this as an equivalent mass at the end that would produce the same frequency response. This is given by m = 0.23m beam.

Our Experiment To obtain a good measure of k and m, we will make 4 measurements of oscillation, one for just the beam and three others by placing an additional mass at the end of the beam.

Our Experiment w Once we obtain values for k and m we can plot the following function to see how we did. w In order to plot m n vs. f n, we need to obtain a guess for m, m guess, and k, k guess. Then we can use the guesses as constants, choose values for m n (our domain) and plot f n (our range).

Our Experiment The output plot should look something like this. The blue line is the plot of the function and the points are the results of your four trials.

Our Experiment w How to find final values for k and m. Solve for k guess and m guess using only two of your data points and two equations. (The larger loads work best.) Plot f as a function of load mass to get a plot similar to the one on the previous slide. Change values of k and m until your function and data match.

Our Experiment w Can you think of other ways to more systematically determine k guess and m guess ? w Experimental hint: make sure you keep the center of any mass you add as near to the end of the beam as possible. It can be to the side, but not in front or behind the end.

Part D w Oscillating Circuits w Comparative Oscillation Analysis w Interesting Oscillator Applications

Oscillating Circuits w Energy Stored in a Capacitor CE =½CV² w Energy stored in an Inductor LE =½LI² w An Oscillating Circuit transfers energy between the capacitor and the inductor.

Voltage and Current w Note that the circuit is in series, so the current through the capacitor and the inductor are the same. w Also, there are only two elements in the circuit, so, by Kirchoff’s Voltage Law, the voltage across the capacitor and the inductor must be the same.

Oscillator Analysis w Spring-Mass w W = KE + PE w KE = kinetic energy=½mv² w PE = potential energy(spring)=½kx² w W = ½mv² + ½kx² w Electronics w W = LE + CE w LE = inductor energy=½LI² w CE = capacitor energy=½CV² w W = ½LI² + ½CV²

Oscillator Analysis w Take the time derivative

Oscillator Analysis w W is a constant. Therefore, w Also w W is a constant. Therefore, w Also

Oscillator Analysis w Simplify

Oscillator Analysis w Solution x = Asin(ωt) V= Asin(ωt)

Using Conservation Laws w Please also see the write up for experiment 5 for how to use energy conservation to derive the equations of motion for the beam and voltage and current relationships for inductors and capacitors. w Almost everything useful we know can be derived from some kind of conservation law.

Large Scale Oscillators Tall buildings are like cantilever beams, they all have a natural resonating frequency. Petronas Tower (452m) CN Tower (553m)

Deadly Oscillations The Tacoma Narrows Bridge went into oscillation when exposed to high winds. The movie shows what happened. physics/tutor/2210/mechanical_oscilla tions/ In the 1985 Mexico City earthquake, buildings between 5 and 15 stories tall collapsed because they resonated at the same frequency as the quake. Taller and shorter buildings survived.

Atomic Force Microscopy -AFM w This is one of the key instruments driving the nanotechnology revolution w Dynamic mode uses frequency to extract force information Note Strain Gage

AFM on Mars w Redundancy is built into the AFM so that the tips can be replaced remotely.

AFM on Mars w Soil is scooped up by robot arm and placed on sample. Sample wheel rotates to scan head. Scan is made and image is stored.

AFM Image of Human Chromosomes w There are other ways to measure deflection.

AFM Optical Pickup w On the left is the generic picture of the beam. On the right is the optical sensor.

MEMS Accelerometer w An array of cantilever beams can be constructed at very small scale to act as accelerometers. Note Scale

Hard Drive Cantilever w The read-write head is at the end of a cantilever. This control problem is a remarkable feat of engineering.

More on Hard Drives w A great example of Mechatronics.