Chapter 3. Amplifiers and Signal Processing John G. Webster

Slides:



Advertisements
Similar presentations
Introduction Goal: Understand the design of op-amp based ICs (comparators, oscillators, integrators, differentiators, instrumentation amplifiers) for applications.
Advertisements

Operational Amplifiers
Operational Amplifiers 1. Copyright  2004 by Oxford University Press, Inc. Microelectronic Circuits - Fifth Edition Sedra/Smith2 Figure 2.1 Circuit symbol.
Chapter 7 Operational-Amplifier and its Applications
CHAPTER 3: SPECIAL PURPOSE OP-AMP CIRCUITS
Chapter 1. Basic Concepts of Medical Instrumentation Walter H. Olson
Experiment 17 A Differentiator Circuit
ENTC 3320 Absolute Value.
8C Inleiding Meten en Modellen – 8C120 Prof.dr.ir. Bart ter Haar Romeny Dr. Andrea Fuster Faculteit Biomedische Technologie Biomedische Beeld.
Waveform-Shaping Circuits
Chapter 3. Amplifiers and Signal Processing John G. Webster
Operational Amplifiers
1 ECE 3336 Introduction to Circuits & Electronics MORE on Operational Amplifiers Spring 2015, TUE&TH 5:30-7:00 pm Dr. Wanda Wosik Set #14.
Astable multivibrators I
Content Op-amp Application Introduction Inverting Amplifier
Chapter 8 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Characteristics of Op-Amp &
Integrator Op Amp Amplifier
EKT314/4 Electronic Instrumentation
A Differentiator Circuit.  All of the diagrams use a uA741 op amp. ◦ You are to construct your circuits using an LM 356 op amp.  There is a statement.
Experiment 17 A Differentiator Circuit
Chapter 8 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Chapter 2 Basic Concepts of Electronics. Figure 2.1 Electric current within a conductor. (a) Random movement of electrons generates no current. (b) A.
Differential Amplifier
Data Acquisition ET 228 Op –Amp Applications Subjects Covered Overview of OP Amp Applications High Resistance Voltmeters Phase Shifter Circuit Integrators.
Transistor Amplifiers
Microelectronic Circuits, Sixth Edition Sedra/Smith Copyright © 2010 by Oxford University Press, Inc. C H A P T E R 02 Operational Amplifiers.
10/11/2015 Operational Amplifier Characterization Chapter 3.
Operational Amplifiers. Chapter 14. Operational Amplifiers.
1 Fundamentals of Microelectronics  CH1 Why Microelectronics?  CH2 Basic Physics of Semiconductors  CH3 Diode Circuits  CH4 Physics of Bipolar Transistors.
An understanding of the complex circuitry within the op amp is not necessary to use this amplifying circuit in the construction of an amplifier.
UNIT – III : OP-AMPS AND APPLICATIONS
Fundamentals of Electric Circuits Chapter 5 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Operational Amplifiers The operational amplifier, also know as an op amp, is essentially a voltage amplifier with an extremely high voltage gain. One of.
3/19/2016 Subject Name: LINEAR IC’s AND APPLICATIONS Subject Code:10EC46 Prepared By: Kumutha A Department: Electronics and Communication Date:
© From J. G. Webster (ed.), Medical instrumentation: application and design. 3 rd ed. New York: John Wiley & Sons, Figure 3.1 Op-amp equivalent circuit.
1 Chapter 8 Operational Amplifier as A Black Box  8.1 General Considerations  8.2 Op-Amp-Based Circuits  8.3 Nonlinear Functions  8.4 Op-Amp Nonidealities.
1 Operational Amplifiers 1. 2 Outlines Ideal & Non-ideal OP Amplifier Inverting Configuration Non-inverting Configuration Difference Amplifiers Effect.
Operational Amplifiers 1. Copyright  2004 by Oxford University Press, Inc. Microelectronic Circuits - Fifth Edition Sedra/Smith2 Figure 2.1 Circuit symbol.
NON LINEAR IC APPLICATION USING OP AMP NAME:- ROLL NO. ROHAN V. KHRISTI 14ELEE310 AFJAL A. RATHOD 14ELEE311 NIKUNJ K. PARMAR 14ELEE312 SUB :- ANALOG ELECTRONIC.
1 UNIT –V Signal Generators and Waveform- Shaping Circuits.
An operational amplifier (Op-Amp) is a differential amplifier that amplifies the difference of voltages applied to its two input terminals (differential.
 The differentiator or differentiating amplifier is as shown in figure.  This circuit will perform the mathematical operation of differentiation.
BME 311: BIOMEDICAL INSTRUMENTATION I Lecturer: Ali Işın
APPLICATIONS OF OP-AMPS
Figure 3. 1 Op-amp equivalent circuit. The two inputs are 1 and  2
Operational Amplifiers
Ch 03 Amplifiers and Signal Processing
Electronic Devices and Circuit Theory
Open book, open notes, bring a calculator
Operational Amplifier
ECE 1270: Introduction to Electric Circuits
Absolute Value.
Analogue Electronic 2 EMT 212
Applications of operational Amplifiers
Alexander-Sadiku Fundamentals of Electric Circuits
Examples of Negative Feedback Applications: A) Inverting Amplifiers
OP-AMPS: basics & Inverting-amplifier
Wave Generation and Shaping
Feedback Amplifiers.
Industrial Electronics
تقویت کننده های عملیاتی
Figure 3. 1 Op-amp equivalent circuit. The two inputs are 1 and  2
Operational Amplifier (Op-Amp)-μA741
Chapter 4 – Operational Amplifiers – Part 2
Fundamentals of Electric Circuits Chapter 5
ELECTRONICS II 3rd SEMESTER ELECTRICAL
Alexander-Sadiku Fundamentals of Electric Circuits
Chapter 5 OUTLINE Op-Amp from 2-Port Blocks
Chapter 5 Operational Amplifiers
Presentation transcript:

Chapter 3. Amplifiers and Signal Processing John G. Webster Medical Instrumentation Application and Design, 4th Edition John G. Webster, Univ. of Wisconsin, Madison ISBN: 978-0-471-67600-3

fig_03_01 Figure 3.1 Op-amp equivalent circuit. The two inputs are vl and v2. A differential voltage between them causes current flow through the differential resistance Rd. The differential voltage is multiplied by A, the gain of the op amp, to generate the output-voltage source. Any current flowing to the output terminal vo must pass through the output resistance Ro.

fig_03_02 Figure 3.2 Op-amp circuit symbol A voltage at v1, the inverting input, is greatly amplified and inverted to yield vo. A voltage at v2, the noninverting input, is greatly amplified to yield an in-phase output at vo.

fig_03_03 Figure 3.3 (a) An inverting amplifier. Current flowing through the input resistor Ri also flows through the feedback resistor Rf. (b) A lever with arm lengths proportional to resistance values enables the viewer to visualize the input–output characteristics easily. (c) The input–output plot shows a slope of –Rf/Ri in the central portion, but the output saturates at about ±13 V. fig_03_03

figun_03_01 Figure E3.1 (a) This circuit sums the input voltage vi plus one-half of the balancing voltage vb. Thus the output voltage vo can be set to zero even when vi has a nonzero dc component, (b) The three waveforms show vi, the input voltage; (vi + vb/2), the balanced-out voltage; and vo, the amplified output voltage. If vi were directly amplified, the op amp would saturate.

fig_03_04 Figure 3.4 (a) A follower, vo = vi. (b) A noninverting amplifier, vi appears across Ri, producing a current through Ri that also flows through Rf. (c) A lever with arm lengths proportional to resistance values makes possible an easy visualization of input–output characteristics, (d) The input–output plot shows a positive slope of (Rf + Ri)/Ri in the central portion, but the output saturates at about ±13 V. fig_03_04

Figure 3.5 (a) The right side shows a one-op-amp differential amplifier, but it has low input impedance. The left side shows how two additional op amps can provide high input impedance and gain, (b) For the one-op-amp differential amplifier, two levers with arm lengths proportional to resistance values make possible an easy visualization of input-output characteristics. fig_03_05

fig_03_06 Figure 3.6 (a) Comparator. When R3 = 0, vo indicates whether (vI + vref) is greater or less than 0 V. When R3 is larger, the comparator has hysteresis, as shown in (b), the input–output characteristic.

fig_03_07 Figure 3.7 (a) Full-wave precision rectifier. For vi > 0, the noninverting amplifier at the top is active, making vo > 0. For vi < 0, the inverting amplifier at the bottom is active, making vo > 0. Circuit gain may be adjusted with a single pot. (b) Input–output characteristics show saturation when vo > +13 V. (Reprinted with permission from Electronics Magazine, copyright © December 12, 1974; Penton Publishing, Inc.) (c) One-op-amp full-wave rectifier. For vi < 0, the circuit behaves like the inverting amplifier rectifier with a gain of +0.5. For vi > 0, the op amp disconnects and the passive resistor chain yields a gain of +0.5. fig_03_07

fig_03_08 Figure 3.8 (a) A logarithmic amplifier makes use of the fact that a transistor's VBE is related to the logarithm of its collector current. With the switch thrown in the alternate position, the circuit gain is increased by 10. (b) Input–output characteristics show that the logarithmic relation is obtained for only one polarity; X1 and X10 gains are indicated.

fig_03_09 Figure 3.9 A three-mode integrator. With S1 open and S2 closed, the dc circuit behaves as an inverting amplifier. Thus vo = vic and vo can be set to any desired initial condition. With Si closed and S2 open, the circuit integrates. With both switches open, the circuit holds vo constant, making possible a leisurely readout.

fig_03_10 Figure 3.10 Bode plot (gain versus frequency) for various filters. Integrator (I); differentiator (D); low pass (LP), 1, 2, 3 section (pole); high pass (HP); bandpass (BP). Corner frequencies fc for high-pass, low-pass, and bandpass filters.

figun_03_02 Figure E3.2 The charge amplifier transfers charge generated from a piezoelectric sensor to the op-amp feedback capacitor C.

fig_03_11 Figure 3.11 A differentiator. The dashed lines indicate that a small capacitor must usually be added across the feedback resistor to prevent oscillation.

Figure 3.12 Active filters. (a) A low-pass filter attenuates high frequencies, (b) A high-pass filter attenuates low frequencies and blocks dc. (c) A bandpass filter attenuates both low and high frequencies. fig_03_12

fig_03_13 Figure 3.13 Op-amp frequency characteristics. Early op amps (such as the 709) were uncompensated, had a gain greater than 1 when the phase shift was equal to -180°, and therefore oscillated unless compensation was added externally. A popular op amp, the 411, is compensated internally, so for a gain greater than 1, the phase shift is limited to -90°. When feedback resistors are added to build an amplifier circuit, the loop gain on this log-log plot is the difference between the op-amp gain and the amplifier-circuit gain. fig_03_13

fig_03_14 Figure 3.14 Noise sources in an op amp. The noise-voltage source vn is in series with the input and cannot be reduced. The noise added by the noise-current sources in can be minimized by using small external resistances.

fig_03_15 Figure 3.15 The amplifier input impedance is much higher than the op-amp input impedance Rd. The amplifier output impedance is much smaller than the op-amp output impedance Ro.

fig_03_16 Figure 3.16 Functional operation of a phase-sensitive demodulator. (a) Switching function, (b) Switch, (c), (e), (g), (i) Several input voltages, (d), (f), (h), (j) Corresponding output voltages.

fig_03_17 Figure 3.17 A ring demodulator This phase-sensitive detector produces a full-wave-rectified output vo that is positive when the input voltage vi is in phase with the carrier voltage vc and negative when vi is 180° out of phase with vc.

fig_03_18 Figure 3.18 A square wave of period T oscillates between two values. From J. G. Webster, Ed., Bioinstrumentation, New York: John Wiley & Sons, 2004.

fig_03_19 Figure 3.19 The 555 timer. (a) Pinout for the 555 timer IC. (b) A popular circuit that utilizes a 555 timer and four external components creates a square wave with duty cycle > 50%. (c) The output from the 555 timer circuit shown in (b). From J. G. Webster, Ed., Bioinstrumentation, New York: John Wiley & Sons, 2004.