Requirements on a CIPP-System. Requirement on a CIPP-System.

Slides:

Advertisements

Similar presentations

First EUREKA meeting Тhe activities of the EUREKA project DE_AMATECH in the year PROJECT Development of new actuators, materials and technology.

Advertisements

Fiber Reinforced Plastic beam manufacturing process

Euro-Zel th International Symposium Advanced Composite Materials for the Railroad cars Presented by Irina Garustovich Moscow State University of.

KORSCH Tablet Compression Technology

The New Technology To Save Primary Energy And To Reduce CO2 Emission

Is presenting:.

VI. GREENHOUSE COVERINGS A. Selection - factors to consider 1. Photosynthesis –Transmission vs plant reception 2. light quality – nanometers.

The Best Solution for CIPP American Made, American Support Introducing America’s First UV Cured Fiberglass CIPP.

RESEARCH PROGRAMS Culvert Liners High Value Research Sue Sillick Montana Department of Transportation July 2011.

S URE FIT ® / R.TEC ® CLOSE-FIT-LINER AGRULINE. CONTENTS  Introduction – current situation  Production  Installation  Advantages  Quality assurance.

BKP-BEROLINA UV STABILIZED LINER TECHNOLOGY TECHNOLOGY BROUGHT TO YOU BY- DATTATREYA INC.

1470 NW 107 th Ave Suite E, Miami, FL Phone:

Matt Bobinski Karen Cariaga Zane Gravino HIGH FIBER.

The simplest of the fabrication processes, hand lay-up is used in low-volume production of large products, e.g., wind turbine components, concrete forms,

SPRAY-UP. WHAT IS SPRAY-UP? one or more continuous fiber rovings fed through a chopper one or more continuous fiber rovings fed through a chopper fiber.

   About Us Catalogue of Products Exit  Contact Us.

Engine friction and lubrication

Mechanical Engineering Department Advanced Composites Dr. Talal Mandourah 1 Lecture 11 & 12 Processing Routes Compression Molding: -One type is matched.

Mechanical Properties of Roebel Coated Conductor Cable A.Kario 1, S. Otten 1,2, C. M. Bayer 1, M. Vojenciak 1,3, A. Kling 1, B. Ringsdorf 1, B. Runtsch.

DR.PRADIP DUTTA Department of Mechanical Engineering Indian Institute of Science Bangalore.

Magnetic circuits of transformers. Magnetic circuits of transformers - assembly Obtuse layout (no-overlapping) easy assembly for small-sized transf. disadvantages:

The simplest of the fabrication processes, hand lay-up is used in low-volume production of large products, e.g., wind turbine components, concrete forms,

FIBROUS REINFORCEMENT Structure: 1.Continuous bundles of fibers. 2.Woven fabrics. 3.Chopped fiber.

 Single Component Products TT-P-1952E - Waterborne traffic paint TT-P-1952E - Waterborne traffic paint A-A-2886A - Solvent traffic paint A-A-2886A - Solvent.

HEATING SYSTEMS AND SANITARY INSTALLATION OUT OF PP - R AGRUSAN.

Marc Crans Chris Henderson Matthew Leroux Deryl Sedran 1.

We master aggressive media Surface Protective Systems Refractory Systems Plastics Engineering Industrial Corrosion Protection KERAVERIN / KERAPOLIN.

1 COMPOSITE MATERIALS What are composite materials? Two or more materials bound together Example from civil engineering: Concrete reinforced with steel.

Robert Gleim Oct. 27 th,  Pipe is designed to handle the following load conditions: ◦ A minimum design life of 20 years at MAOP and MAOT ◦ Hydro.

Mechanical Engineering Department Advanced Composites Dr. Talal Mandourah 1 Lecture 11 & 12 Processing Routes Molding Compound -Short fibers, preimpregnated.

MAE 661 Laminated Composites Introduction Materials and Processes

Silver / Polystyrene Coated Hollow Glass Waveguides for the Transmission of Visible and Infrared Radiation Carlos M. Bledt a and James A. Harrington a.

Eucard WP 7.3 HFM Winding and tooling tests Insulation choice F.Rondeaux /01/2011 Dipole design review- II-8 Winding and tooling tests – insulation.

Composite Materials Manufacturing Composite Materials Manufacturing 정분방.

LSA Tube is a heat-shrinkable tube with an excellent insulation and flexibility. Light-weighted and thin, it can be applied to the severely bent part.

4.2 Notes RESISTANCE IN FLUID SYSTEMS. Resistance in Fluid Systems Drag - the force opposing motion when a solid moves through a fluid Drag occurs only.

PSB dump: proposal of a new design EN – STI technical meeting on Booster dumps Friday 11 May 2012 BE Auditorium Prevessin Alba SARRIÓ MARTÍNEZ.

Reactor pressure vessels of WWER (materials and technology) Janovec, J

Alumina Reinforced High Porosity Al-alloys with Extreme Hardness Dr. László A. Gömze 1, University of Miskolc, Miskolc, Hungary Tel.:

Put an end to corrosion & water ingress by self-healing fully amorphous visco- elastic technological systems Solution for Risers.

Two Categories of Plant Tissues AP Biology Spring 2011.

Design Guidelines Injection Moulding Engineering Design.

Extrusion Plastics 001 Profile Extrusion. Extrusion Plastics 001 Introduction – Extrusion is a process that can make long parts with a constant cross-section.

10-Jun-16S.Movchan Straw manufacturing and QC1 Straw manufacturing conditions and QC tape and straw parameters specification conditions of straw production.

Polymer Matrix Composites Matrix Resins and Composite Fabrication

Epoxy Infusion System – Hardener SIN B17 Polynt’s SIN B17 is the world’s first Epoxy resin hardener based on anhydride chemistrythat has been specially.

Wet laid, Air laid, and Random laid

B [OT - Mechanics & Cooling] Stefan Gruenendahl February 2, 2016 S.Grünendahl, 2016 February 2 Director's Review -- OT: Mechanics &

Cold Fluid Applied Reinforced Roofing. Agilast Cool Roof Systems Highly durable Water based Waterproof Reinforced with tough polyester fabrics/chopped.

Fluid Power Control FLUID POWER INTRODUCTION TO PNEUMATICS # Learning Objectives : Upon completion of this chapter, Student should be able to …  Describe.

Lesson 7: Thermal and Mechanical Element Math Models in Control Systems ET 438a Automatic Control Systems Technology 1lesson7et438a.pptx.

NATIONAL CONFERENCE ON RECENT ADVANCES IN COMPOSITES M.SURENDER NATH INNOVATIVE FRP SYSTEMS PVT LTD PANNAMGADU, TADA 16/06/2012 Composites For Wind Energy.

Rosava Group Engineering ,

High Density Polyethylene Pipes Our Products & Services

27-28 April 2015 Eng. Mubarak Yusuf Al-Kawari Presented by:

Reinforced Plastics.

Sierra Assembly Technology Inc.

AND AFTER INSTALLATION Technical Director, NASSCO

Greenhouse Management

SANDWICH CONSTRUCTION

China Beihai Group.

Fibre-reinforced plastic

WATER MAIN REHABILITATION

- BEAM Sinusoidal Web Beam

INTD 503- Materials Topic: FABRIC

New ST line with high energy saving for ECO applications

HIE-LINAC status report

ET 438a Automatic Control Systems Technology

Vehicle Components Business

Presentation transcript:

Requirements on a CIPP-System

Requirement on a CIPP-System

Requirements on a CIPP-System Low loss of diameter Short installatoin time 50 years service life Smooth inner surface Chemical resistance Long storage time Advantages in general Installations length as long as possible Quality controlled production Low shrinkage Ready to install Good mechanical qualities Excellent stretching behavior

Requirements on a CIPP-System Viscosity, curing system, resin Long storage time Short installation time Chemical resistance Reinforce- ment Length of liner as long as possible Low shrinkage Good mechanical qualities Low loss of diameter Overlapping zone Excellent stretching behavior Inner film, outer film, rope, impregnation Ready to install Should be done in factory Thickener UV-light Polyester, Vinylester Glass fiber Layer construction Advantages of elements

Requirements on a CIPP-System Thickener Long storage time During impregnation low viscosity After impregnation an optimal level If level will become to high expansion is handicapped. If level is to low resin starts flowing. Advantages Viscosity of resin Viscosity change with different dosages

Requirements on a CIPP-System Short installation time Fast curing speed up to 600 mm/min (depends on wall thickness and light source). Liner installation without overtime possible. No unnecessary hindrance to traffic in towns, air traffic at airports, material flow in industrial plants. Curing System Curing systemUV-light

Requirements on a CIPP-System Long storage time Curing is independent of temperature (exclusively started by UV radiation). Changes of the time shedule have no influence of quality (within 6 month after manufacturing). Simple logistic. No cooling transport required. ReinforcementUV-light Curing System

Requirements on a CIPP-System Reinforcement by glass fiber Length of liner as long as possible Low shrinkage Low loss of diameter Good mechanical qualities Diameter 300 mm, wall thickness 5 mm, max. pulling force: 234 kN (4,643 m) 0,5 % Ring modulus > N/mm 2 (for comparison purpose: Polyester Felt < N/mm 2 ) E.g. diameter of 600 mm, SN : Wall thickness - glass fiber reinf. 13,5 mm, Wall thickness – Polyester Felt ~ 20 mm

Requirements on a CIPP-System Excellent stretching behavoir Woven roving Chopped strand mat Properties Overlapping zoneLayer construction

Requirements on a CIPP-System Diameter change from 450 mm to 500 mm Overlapping zoneLayer constructionGood mechanical qualities Properties

Requirements on a CIPP-System Thank You For Your Attention! BKP Berolina Polyester GmbH & Co. KG Am Zeppelinpark Berlin Germany Phone: +49 (30) Fax: +49 (30) Web: