Reading Technical Drawings: Test

Slides:

Advertisements

Similar presentations

Equivalent lists. The Ratio p : q is What is the scaling from p to q as as a fraction? as a decimal ? Increase or Decrease ? INVERSE The Ratio q : p is.

Advertisements

Objective: Develop plans for kitchen cabinets.

1 of 4 LESSON #13 A REVIEW OF ORTHOGRAPHIC PROJECTION

Reading Technical Drawings

Unit 4 Extension Lines And Dimension Lines

1 Blueprint Reading for the Machine Trades, Sixth Edition Unit 12: Auxiliary Views Russ Schultz and Larry Smith PowerPoint presentation created by LaVonne.

Fractional/decimal equivalents There are several uses for equivalents for fractions in our shop. We need to know that ½ is.500 To use taps and dies To.

Fractions, Decimals, & Percent Conversions

Demonstrate correct drawing procedures

People Fractions. Problem 1 of 20 Answer 1 = 10 Problem 2 of 20 Answer 2 = 5.

6.14 SOL 6.14 The student, given a problem situation, will

Functional Maths Skills Online Activities Northern College

By: Sean F.. Solving Equations Finding VolumePercent Increase and Decrease Measure of angles and shapes Multiplying Fractions and Decimals

Decimals and Fractions

Which answer includes a mixed number that is equivalent to one and three twelfths.

Converting Fractions to Decimals

Catalyst Thursday, October 6, 2011 Of the 75 teachers at a school, 15 teach mathematics. What percent of the teachers at the school teach mathematics?

FIND THE UNIT RATE 9000 tickets 6 hours. FIND THE UNIT RATE 240 tickets = x tickets hour minute.

I can use proportions to solve problems involving scale.

Structural Drafting Connection Details and Gages.

Multiplication of Decimal Fractions STEPS : 1. Count the number of places BEHIND the decimals 2. Treat the problem like you are multiplying whole numbers.

Scale Drawing - a two dimensional drawing that is similar to the object it represents. Scale Model - a three-dimensional model that is similar to the object.

The Fractions Challenge When you see a fraction, change it into the equivalent decimal number. When you see a decimal number, change it into the equivalent.

1 SheetCourse: Engineering Graphics 1504Memorial University of Newfoundland Engineering Graphics 1504 Lecture 2 – Orthographic Sketches Objectives l Recap.

Chapter 1 Section 3 Measurement. Objectives and Questions.

Converting Fractions to Decimals Ms. Stewart Math 7 COPY SLIDES WITH A PENCIL ICON.

Lesson 4: Equivalent Fractions  Date:  Objective: SWBAT find equivalent fractions and compare fractions  Do Now:  DON”T DO THE OPENING. NEED TO ADJUST.

Pre-Algebra 7-9 Scaling Three-Dimensional Figures Pre-Algebra Homework Page 378 #10-18 & #32-39 (SR) Answers.

Dimensioning 1’ - 8” 8’ - 4” Unit 8.

WALT- use a number line to help round numbers to the nearest whole number to the nearest whole number to the nearest whole number.

© Nuffield Foundation 2012 Free-Standing Mathematics Activity Fractions, decimals, percentages.

5 Minute Math In which place is the 4 in each of the following: 140,399 48, ,394 Write 2 equivalent fractions for each of the following:

Equivalents ½ ½ ⅔.

Fractions and Decimal Fractions Fractions Decimal Fractions

Introduction to Dimensioning © 2012 Project Lead The Way, Inc.Introduction to Engineering Design.

Working with Percentages. Writing percentages as fractions ‘Percent’ means ‘out of 100’. To write a percentage as a fraction we write it over a hundred.

6.14 SOL 6.14 The student, given a problem situation, will a) construct circle graphs; b) draw conclusions and make predictions, using circle graphs; and.

On each number line, the distance from 0 to 1 represents one mile. These students each marked the distance they live from school on the number lines below.

Detail Drawings Suggested Layouts Dimensioning Guidelines

Measuring and Drawing Angles with a Protractor. Protractor Center Hole.

Teknologi Dan Rekayasa

Type your name and send:

Find the common denominator. Make equivalent fractions.

Fractions and decimals review

Russ Schultz and Larry Smith

Map scales A scale drawing is a drawing in which all dimensions have been reduced in exactly the same proportion. For example, if a model boat is made.

Dimensioning Dimensioning PLTW Gateway®

Chapter 4 Orthographic Writing.

Dimensioning Dimensioning Gateway To Technology®

Fractions and Decimals

Write this fraction as a decimal.

Dimensioning Dimensioning PLTW Gateway®

How to Use a Protractor.

Break down Lance rack Cut one of each of these for each rack

Today we will explain fractions in different ways

Fractions, Decimals & Percentages

Operations and Rational Numbers (Fractions)

Isometric and Oblique Pictorials

Designing Open Tasks for All Students

Understanding Number I can check adding and subtracting calculations by rounding to the nearest 10 or 100. I use knowledge of context to decide if an answer.

Forging new generations of engineers

Objective: Develop plans for kitchen cabinets.

Dimensioning Dimensioning Gateway To Technology®

Dimensioning Dimensioning PLTW Gateway®

Understanding Number I can check adding and subtracting calculation by rounding whole numbers to the nearest 10, 100 and I use knowledge of context.

Extending your knowledge Circumference of a circle =

A series of vessels of uniform cross section look like letters when viewed face-on. They are 1cm thick, and the corners of the vessels have either whole.

Powers of Ten – Negative Exponents

Presentation transcript:

Reading Technical Drawings: Test Foundations of Manufacturing

Thermostat Gasket 1. What is the part number? 11A001

Thermostat Gasket 2. What is the name of the part? Thermostat gasket

Thermostat Gasket 3. What is the drawing size? (A, B, or C) A

Thermostat Gasket 4. What scale is the drawing? 1:1

Thermostat Gasket 5. Use words to explain the answer to question 4. Actual size

Thermostat Gasket 6. How thick is the part? .06

Thermostat Gasket 7. Is the part symmetrical? Yes

Thermostat Gasket 8. Which system of dimensioning was used? (Refer to page 21.) Decimal

Thermostat Gasket 9. What is the fractional equivalent of the center hole size? 2 3/16

Thermostat Gasket What is the fractional equivalent of the mounting hole spacing? (Refer to the equivalency chart, page 25.) 3 5/8

Thermostat Gasket 11. Calculate the longest overall dimension of the part. 4.24

Thermostat Gasket 12. Calculate the overall dimension of the part (height.) 2.88

Thermostat Gasket 13. Calculate the material remaining between the large hole and the nearest outside edge. .345

Thermostat Gasket 14. Calculate the material remaining between the small hole and the nearest outside edge. .155

Thermostat Gasket 15. Calculate the material remaining between the large hole and the nearest small hole. .56

Reading Technical Drawings: Test Foundations of Manufacturing