In this configuration the nose strut tube needs to be cut off. The old nose fork and block/steering collar are removed. The new block must be installed.

Slides:



Advertisements
Similar presentations
How To Catch A Swarm Using Buckets. Take 2 plastic buckets and cut a large matching hole in the bottom of each. Using screen wire, preferably 1/8 hardware.
Advertisements

How to install a PL-259 My Way! by Steve, N1NXU. Start with a clean cut. Notice how the top cable end is a nice clean round cut. It was cut with a cable.
Gable Ends, Verge, Eaves & Erection of Gable Roofs
Instructions for making plunger fork tool. Drawing for the trigger assembly.
Frame Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team
1 STEPMILL 7000 PT ASSEMBLY INSTRUCTIONS PART NUMBER
Step-by-step assembly instructions
Trim Fwd Spar End Brackets July 6, H2-2, Horizontal Stab Rear Spar 7H1-2, Stab Full Rib Corner of Forward.
ASSEMBLY INSTRUCTIONS. 2 ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: SIDE CUTTING PLIERS PRY BAR 7/16” & 9/16” WRENCH 3/16” ALLEN WRENCH T-15 TORQUE.
Making a trap cage. You need plastic bottles, wire, string, a plastic bag and tools.
Transformation of Energy Through Digestion
Hydraulic Digger Step-by-step assembly instructions (c) 2013 Mechanical Kits Ltd.1.
106. Nov 2008 / RH “Pavement Breaker” Rosta-Repair INDUSTRIAL PRODUCTS GROUP Remove nut on left side handle (w/o switch) and remove the side handle.
Tool Use Strip wire. Soldering Iron Step 1: Tinning the iron Tinning helps to make soldering easier and quicker while keeping the iron in good condition.
Features Specs Price List Torque Wrench CCCP Space Systems CCCP Model 757XS.
Energy Coffee Can Racer Lab
Model 12 Intek Horizontal OHV Crankcase Disassembly and Assembly Lab #7.
Common Problems Freeboard Anchors and U-bars Sag System hardware.
INSTALLATION INSTRUCTIONS FOR GERARD METAL SHINGLES
The Estes Viking Rocket
Approved Training Manual’s Lesson Plans And Courseware STAR MARIANAS AIR, INC. Initial New Hire – Flight Crew Part III – Aircraft Ground Training Section.
Components Connection Jig Graph Paper (#4101) Mounting Blocks (#5902) Nails Tape Measure Pen Hammer Customer Coordinates.
Making A Motor Exploring the Magic of Electricity.
Manufacturing Assembly Plan P Mechanical Spine Test Platform.
Polaris 6x6 UTV Instructions for Fuel Tank Vent Tube Modification 2005 – 2009 models For further information contact: Michelle Ryerson or Carl Dorsey,
Building A Model Rocket
Title: Corvette C5 Column Lock Bypass Originator: John Neese Date: 30 Jan 2005 Revision: Sheet: 1 of 6 Column Lock Bypass.
By Mattia Costa 9H. I used my sisters old dress to unstitch the top part from it leaving me with the skirt. After that I went to the op shops and looked.
July Vehicle Selection – BMW 3 series (E46) 318i, 87kW, 1998 – 2001.
Respiratory Surfaces Making a Model of the Lungs.
3 Little Pigs Story Video
K u r e n t. About the Carnival One of the most important traditions in Slovenia is related to Carnival (on Thursday in February). The "strange" figure.
Installing a single Dreamscreen Set unit in place and attach with 2 ½ “ screw. Do not tighten the screw yet, tighten just enough to keep from falling.
Up and Over Step-by-step assembly instructions (c) 2013 Mechanical Kits Ltd.1.
Model 12 Intek Horizontal OHV
SLHC Engineering Upgrade FCAL Remove-Install step by step procedure. Mircea Cadabeschi-University of Toronto March 01,
A-Frame Operation The A-Frame will provide support for odd shaped loads, loads where you are unable to get directly below the load, and for stabilizing.
1 MOMENTUM 3800 RC ASSEMBLY INSTRUCTIONS PART NUMBER
Purpose The purpose of this activity is to make a working model of the lungs.
Easy Reach 7.0 Honda Element Packing List QtyDescriptionPacked 115ft 10ga Red Wire 16ft 10ga Black Wire 140amp Breaker 23/8 Yellow Ring Terminals 25/16.
Chocolate Mold Design. Design your desired finished product part.
Use original rear consol support/seat belt mountUse supplied console support bracket (front.) Unit Can possibly pop pocket off lower door. IF NOT,
Foldable Tie Book Instructions. Materials Needed 2 pieces of scrap paper Glue stick Paper Hole Punch Tool 1 piece of yarn cut to one arm’s length.
MNM Fatal Falling Material Accident Falling Material Accident January 6, 2009 (California) January 6, 2009 (California) Sand & Gravel Operation.
Assembly of steering.
GENERAL CAUTION TOOLS REQUIRED ASSEMBLY AND INSTALLATION
Assembly Instructions:
LANDING GEAR SYSTEMS THIS TRAINING MANUAL HAS BEEN PREPARED FOR MAINTENANCE TECHNICIANS AND DOES NOT SUPERSEEDED INFORMATION CONTAINED IN APPLICABLE AIRCRAFT.
InNova Perfecto Headrest Assembly Instructions
The Lung Model Lesson 16.
Easy-Cliner Manual Cable Version Assembly Instruction
Landing gear systems.
Hall A Target Status 9/27/16 Dave Meekins.
Siren Name: Lenka Somorová.
installing electrical system
Step-by-step assembly instructions

How to Fix “Invalid Refill” Error in Lexmark Printer: Lexmark Printer Support | Printer Customer Support Lexmark Printer Support Printer Customer Support.
How to Install a Garage Door.
‘Bling up’ your bike or scooter.
المدخل إلى تكنولوجيا التعليم في ضوء الاتجاهات الحديثة
זכויות סוציאליות.
Exploring the Magic of Electricity
AQUARIUM DREAMS CHALLENGE ASSIGNMENT.
Please plug the 4 rudder pedal attachment bushings prior to powder coat also plug all nut plate holes.
Membrane Potentiometer Carrier – Assembly Diagrams
Can we apply our “3 Basic Steps” process to power a non-Aristo loco?
Make your CORRUGATOR run BETTER
Materials By Products Bottle Reshaping Bottle Cleaning Making String
Presentation transcript:

In this configuration the nose strut tube needs to be cut off. The old nose fork and block/steering collar are removed. The new block must be installed where the original scissor link was attached. The strut tube is cut off flush with bottom of fork. The nose block and nose fork are installed in accordance with instructions provided.

In this configuration the nose strut tube needs to be cut off. This was an improper installation made by a customer. The new block should be installed in place of preexisting block/steering collar. Strut tube is cut off flush with bottom of fork. The torque link attaches to new Airglas block. The new block and nose fork are installed in accordance with instructions provided.

In this configuration the nose strut tube does not require cutting. The nose fork and integrated block are removed and new block is attached to strut tube using the existing holes. The new block and nose fork are installed in accordance with instructions provided.

In this configuration the nose strut tube does not require cutting. The nose fork and integrated block/steering collar are removed and new block is attached to strut tube using the existing holes. The new block and nose fork are installed in accordance with instructions provided.