Presentation of designs to YKK Team leader : Poon San On (Zen) Team members: Lee Man Kit(Jason) Kong Yau Choi(Eddie) Mak Fu Shun(Vincent) Wong Ching Pong.

Slides:



Advertisements
Similar presentations
Pneumatic Valves Lesson 4.
Advertisements

BEST Engineering Mechanics
The Cleveland Load.
Unit Eight Check Valves, Cylinders, and Motors
Optical Manufacturing Solutions 1 Probe Assembly.
Cylinders and Actuators
Hydraulic Power Assist
MU 7 Mak Fu Shun Kong Yau Choi Lee Man Kit Poon San On Zen YKK Project: Automatic adhesive machine.
Mechatronics Department Graduation Project II. OutlineIntroduction. Methodology. Mechanical Design. Control Design.
C-Base Transmission Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team
Technology Education Shop and lab safety Band Saw Scroll Saw
0 Beach Cities Robotics Pneumatics August 12, 2007 Rick Wagner, APM, Redwood I&T Northrop Grumman Corporation.
PROJECT 100. PROJECT 100 DESIGNED TO BE: Cost Effective Compact Strong Simple Light Reliable.
Auto - Drive An Automated Driving Range. Team Members Mike Loiselle Jared Beland Jeremy Paradee.
Initial Design. At this region, here are the 2 adhesive machines given from YKK, which are not shown to reduce complicated drawing. The cylinder with.
Mechanisms Paul Ventimiglia WPI Student, Team 190.
Pneumatic Logic Sensors and Actuators
TOPIC: BEARINGS OBJECTIVE: TO TALK ABOUT THE IMPORTANCE OF BEARINGS WHILE DESCRIBING THE DIFFERENT TYPES OF BEARINGS AND THEIR USES Presenter: SHER AFZAL.
Pneumatic Actuators Brief Overview Kunal Sinha Grad General Engineering EFR : 2 per min.
Mechanical Systems Unit Review. Early Machines machines help us do work and use energy more efficiently early machines were simple devices to help us.
Power Transmission Devices
SAFE LIFTING Did you know? –80% of all Americans will suffer a back injury that will require medical attention? –Once you suffer a back injury, you are.
TOOL: Radial Arm Saw NEXT STEP: Radial Arm Saw RESULTS: Finish Top Apron Pieces at 9” L x 4” W x ¾ “ Th PROJECT Square Plant Stand PART Top Apron # NEEDED.
Conveyor Control using PLC, VFD, and Sensor
MECHANISM Exit Next Page Pulleys 1 Rotary cams 1 Gears 2
Final Review Powerpoint
Course of MT- 362 Material Handling Lecture # 8.
CONNECTING MODULE – conveyor 2 – sorting mechanism (waste bin) 3 – connectors (air, cooling water)
This multimedia product will help you to understand the basic Automotive Engine Parts, The engine, The gearbox, The clutch, The pistons, The crankshaft,
The Elements of Machines.
Sci 701 Unit 6 As learned in Unit 5: Speed, Power, Torque, and DC Motors, a motor can generate a set amount of power. Introduction to Gears Since there.
Software Overview The software that controls the Place n’ Paste is designed to be robust and error proof. With minimal intervention from the user, the.
MACHINE GUARDING. contents  What is a Guard?  Why are guards used?  Where should machine guards be used?  Hazardous Machine Areas  Hazardous Actions.
Unit 4: Mechanical Systems. Topic 2: The Wheel and Axle, Gears, and Pulleys.
Safety Rules for 9 th Grade Shop Radial Arm Saw: Safety Rules Never cut a board that is less than 12 inches long. Always pull the saw using the handle;
Printer Velocity Team 6 Mitchell Fiegel Tom Graf Jaclyn Fissinger Matt Leu Alejandro Buxo Sumit Zaver.
Drawings Review. Drawings Drawings are used to communicate information –Sketch: A drawing done without instruments or measurements, but conveys the general.
Preliminary Design Review Team 1: Game of Ohms Vending Machine.
After completing Unit 6: Gears, Chains, and Sprockets, you will be able to: Identify whether a gear reduction causes a speed reduction or a speed increase,
Levers & Fluids Rig Step-by-step assembly instructions (c) 2012 Mechanical Kits Ltd.
Introduction to 3d Modeling Simple Polygon Modeling Using 3D Max
Power Transmission Devices
BRAKES.
Problem Statement & Conceptual Designs September 6, 2006 Team Moondogs Chris Culver Rahul Kirtikar Elias Krauklis Christopher Sampson Michael Widerquist.
Dumplings Done Right Anneliese Freitag, Ryan Boyle, Josh Gregov, Wenhan Introduction to Engineering Design 100 Section: 16 Team: #3.
Accumulator : A robot mechanism designed to pick up a large number of similar objects.
Multi-Angle Photos to help you build.
Team work : Sherief Gameel el sayed Mohamed Ahmed abd elsalam Omar Medhat ezzat el kordy Presented to : Prof.Yehia Hendawy Eng.
Unit D: Mechanical Systems What is a Simple Machine?  A simple machine has few or no moving parts.  Simple machines make work easier 2.
Automotive Steering System
Double Acting Cylinder
Steering System Function of Steering System
Chapter 4.2 and 4.3 Machines.
Welcome to a world full of machines!
SuperQuest Salem Arms – Best Practices.
MECHANICAL ENGINEERING
BRAKES.
RUBE GOLDBERG Mr.Masters CADD.
PLC based automated coal crushing and conveyor system
What is a simple machine?
Brakes.
Hagerty Robotics Tesla Training Day.
Mechanical Advantage and Efficiency
Korea University of Technology and Education
INTRODUCTION TO PNEUMATICS
3D Max screen shot Top view Right side view Front view
Complex Mechanical Function
Mechanisms- Levers and linkages
Presentation transcript:

Presentation of designs to YKK Team leader : Poon San On (Zen) Team members: Lee Man Kit(Jason) Kong Yau Choi(Eddie) Mak Fu Shun(Vincent) Wong Ching Pong (Richard)

Introduction Founded in 1966, YKK Hong Kong Limited is as a subsidiary of YKK Corporation. The company is one of the biggest corporation in producing and selling zippers.

We are glad to do the manufacturing project working under YKK. Today, we present the designs of adhesive paper tapping machine.

Adhesive Machine Design 1 By Vincent

Once the box press the senor, cylinder will push the box to the second conveyer. Therefore, the box can change the direction. Sensor

Then the box will pass through the sticking machine.

For the different size of the box, some parts can be adjusted.

Advantages: The mechanism is simple. The cost is relatively low. The box need not to stay in one place and can move through all the process. Disadvantage: The machine is in L-shape, a large area may be needed.

Adhesive Machine Design 2 By Eddie

brush smoother

Operation 1 When the box arrives at the set position, the belt will stop.( There are some sensors to detect the box’s position.) Two gears will start to move in x-direction through the “rack and pinion”. Since there are drafts to connect everything, two adhesive papers are moving in x-direction too.

Operation 2 At the same time, there are a plastic smoother and a brush following it. So the adhesive paper can be sticked on the box. By installing a timer on the machine, the belt will move again when the process is finished.

Pros and Cons Advantages Low in cost User-friendly Disadvantages Big in size (occupied large area) Slow

Designed by Zen 2 stages for sticking the adhesive papers. 1 stage for compressing the adhesive papers against the box. 8 pneumatics to adjust position. 3 sensors with timers to stop the box.

Step 3: The bar is extended with Pneumatic to absorb the adhesive paper using the absorber! Step 1: The box is moved by rollers, there is one sensor to stop there is one sensor to stop the roller from moving when arriving at the mechanism. Step 2: The four pneumatics extend to push the box in the middle position!

Step 4: The Absorber absorbs the adhesive paper and pulls it out to the one end of the box then stop!

Step 5: The Absorber absorbs the adhesive paper and Pulls it out to the one end of the box then stop! Step 6: The cutter is extended to cut off the adhesive paper

Step 7: The Absorber retreats, and return to the beginning position! Step 8: The 4 pneumatics and the cutter retreat! Step 9: The rollers will start moving the box after a few seconds using a timer.

Step 10: The box is moved to the next stage for front attachment! and the absorber return to original position! Step 11: the Front attachment is the same as the Back attachment!

Step 12: The plate will push the two adhesive papers against the box, and make them stick together smoothly and firmly! The plate can rotate 90 degree to compress the latter adhesive paper.

The box is then carried on for next process

Advantages Compacted, everything is done within shorter distance. It requires smaller area, save space. Do not require to turn the box by 90 degree.

Disadvantages Complicated with many mechanisms and parts. Has to stop for a while, the efficiency will be decreased. The cost is high.

Adhesive paper design 4 By Jason

Operation 234 Box stops at 2 Start to put adhesive paper on the box Box stops at 3 Make sure the adhesive paper stick on the box Also, at 2, the adhesive paper start to put on the box Box stops at 4, then 3 will run again its operation

Sticking part cylinder Paste the adhesive paper on the box at right position (operating by rack and pinion) After that, the adhesive paper will reture the starting position by rack and pinion, to the ready state for next side

Pressing part To make sure that the adhesive paper has stricked on the box. Load the “T” shape brush down to the box.

T shape brush brush Gear connected to rack

Adhesive paper roller Adhesive paper Gear connected to rack

Advantages Easy to assemble: Few components to be added in the system Effenient: Two adhesive paper can be put for two boxes at the same by two structures Space saving : only one conveyor is required

Disadvantages The “T” shape brush and lots of sensors will be used to detect the positions of the boxes Time costly: The boxes have to be stopped for the whole operation

Adhesive machine design 4 By Richard

Operation 1 First, the box will be picked up by the pump. Then, the box will be rotated by 90 degrees. Air pumpConveyor 1

Operation 2 After rotation, the box will be on another conveyor with larger width. The adhesive paper device will put the paper on the box and smooth the paper.

Adhesive paper brush Detecting bar Cutter

Operation 3 After the operation, the box will be rotated by 90 degree again. Finally, it is putting back to the conveyor for further process.

Advantages Efficient: Two adhesive papers will be attached and smoothed at the time Time saving: Time can be saved when two pump is used.

Disadvantages The structure is complicated. Cost is relatively high. The box have to move and rotate from one to another place.

Preferred Design Design 1 Reasons: Simple structure Low Cost Shortest Time for each operation