Data Link Protocols(HDLC & PPP)

Data Link Protocols The set of specifications used to implement the DLL. DLL Protocols Synchronous Protocols Character-oriented Bit-oriented Asynchronous Protocols Timing Co-ordination No Timing Co- ordination

Character-Oriented Protocols: interpret a transmission frame as a succession of characters, each usually composed of one byte. (Byte- oriented Protocols) Example: BSC (Binary Synchronous Communication)  Developed by IBM  Specifies half-duplex transmission with stop-and-wait ARQ. Character-oriented Protocols

Bit-oriented Protocols A bit-oriented protocol is a communications protocol that sees the transmitted data as an opaque stream of bits with no semantics, or meaning. Control codes are defined in terms of bit sequences instead of characters. Bit oriented protocol can transfer data frames regardless of frame contents. It can also be stated as "bit stuffing" this technique allows the data frames to contain an arbitrary number of bits and allows character codes with arbitrary number of bits per character. Examples: HDLC & PPP

High Level Data Link Control Most widely used DLL protocol Published by ISO Supports both half-duplex & full-duplex modes in Point-to-point & Multipoint Configurations. Systems using HDLC can be characterized by :  station types,  configurations,  response modes.

HDLC Station Types Primary station —Controls operation of link —Issues commands (frames) —Maintains separate logical link to each secondary station Secondary station —Under control of primary station —Issues responses (frames) Combined station —May issue commands and responses —Combines the features of primary and secondary stations

HDLC Link Configurations Configuration refers to the relationship of hardware devices on a link. Primary, Secondary & Combined stations can be configured in 3 ways: Unbalanced:  One primary and one or more secondary stations.  Supports full duplex and half duplex Balanced:  Two combined stations  Supports full duplex and half duplex Symmetrical:  Each Physical station on a link consists of two logical stations, one a Primary & the other a Secondary

HDLC Link Configurations

HDLC Transfer Modes Normal Response Mode (NRM) —Unbalanced configuration —Primary can only initiate transmission —Secondary may only transmit data in response to command (poll) from primary —Used on multi-drop lines —Host computer as primary —Terminals as secondary

HDLC Transfer Modes Asynchronous Balanced Mode (ABM) —Balanced configuration —Either station may initiate transmission without receiving permission —Most widely used —No polling overhead Asynchronous Response Mode (ARM) —Unbalanced configuration —Secondary may initiate transmission without permission form primary —Primary is responsible for connect, disconnect, error recovery, and initialization —rarely used

HDLC Transfer Modes ( In Nutshell) NRMARMABM Station Type Primary & Secondary Combined InitiatorPrimaryEitherAny

Frame Structure Defines 3 types of frames (I,S,U frames)

Flag Fields Delimit frame at both ends Receiver hunts for flag sequence to synchronize Bit stuffing used to avoid confusion with data containing —The transmitter inserts 0 bit after every sequence of five 1s with the exception of flag fields —If receiver detects five 1s it checks next bit If 0, it is deleted If 1 and seventh bit is 0 (i.e., 10), accept as flag If sixth and seventh bits 1 (i.e., 11), sender is indicating abort

Bit Stuffing Example with possible errors

Address Field Identifies secondary station that sent or will receive frame Usually 8 bits long May be extended to multiples of 7 bits —LSB of each octet indicates that it is the last octet (1) or not (0) All ones ( ) is broadcast

Control Field Different for different frame type —I-frame (information frame) data to be transmitted to user (next layer up) Flow and error control piggybacked on information frames —S-frame (Supervisory frame) Used for flow and error control —U-frame (Unnumbered frame) supplementary link control First one or two bits of control filed identify frame type

Control Field Diagram

Poll/Final Bit Use depends on context Command frame —P bit : used for poll from primary —1 to solicit (poll) response from peer Response frame —F bit : used for response from secondary —1 indicates response to soliciting command

I-frame Contains the sequence number of transmitted frames and a piggybacked ACK N(S)P/FN(R)

S-frame Used for flow and error control SP/FN(R) RR --- receive ready RNR --- receive not ready REJ --- reject on frame N(R) SREJ --- selective reject on N(R) 0

U-frame Mode setting, recovery, connect/diconnect MP/FM1 Unnumbered function bits

Unnumberred frames Set normal response mode (SNRM) Set asynchronous response mode (SARM) Set asynchronous balanced mode (SABM) Disconnect (DISC) Unnumberred acknowledgement (UA) Disconnect mode (DM) Request disconnect (RD) Unnumberred poll (UP) Reset (RSET) Exchange identification (XID) Test (TEST) Frame reject (FRMR)

Information Field Only in information and some unnumbered frames Must contain integral number of octets Variable length

Frame Check Sequence Field FCS Error detection 16 bit CRC Optional 32 bit CRC

HDLC Operation Exchange of information, supervisory and unnumbered frames Three phases —Initialization —Data transfer —Disconnect

PPP ( Point-to-Point Protocol)

Transition States Idle State: link is not being used. Establishing State: When one of the end-points start the communication, the connection goes into the establishing state. Authenticating State: is optional, the two end-points decide during establishing state whether to opt for authenticating state or not. Networking State: the exchange of user control and data packets. Terminating State: Close the link.

Transition States Idle Establishing Authenticating Terminating Networking State Detect Carrier Success Finish Fail Drop Carrier

PPP Flags FlagAddressControlProtocolData & padding FCSFlag