Drager PSS 7000 Breathing Apparatus Set Breathing Apparatus Collaboration Drager PSS 7000 Breathing Apparatus Set Quick Menu To navigate this presentation use slide 4 and click on the numbered icons on the left

To introduce personnel to the Dräger PSS 7000t BA Set. Aim To introduce personnel to the Dräger PSS 7000t BA Set.

Objectives: By the end of this session personnel Will have sufficient knowledge and understanding of the functions relating to the use of the Dräger PSS 7000t BA

Dräger PSS 7000 Cylinder 3 Slides Reducer 1 Slide Back plate 3 Slides Quick Selection Menu Cylinder 3 Slides Reducer 1 Slide Back plate 3 Slides Harness 3 Slides Pneumatics 2 Slides LDV 1 Slide FPS 7000 Face Mask 1 Slide Bodyguard 7000t EMU 3 Slides Log Off

Cylinder: Final Resin Layer Glass Wrap Carbon Wrap Aluminium Liner HIGH PERFORMANCE LIGHT WEIGHT COMPRESSED AIR CYLINDER Final Resin Layer Glass Wrap Carbon Wrap Aluminium Liner Anti corrosive layer Cylinder: Aluminium lined Carbon Fibre wrap coated in glass fibre wrap finished with an Epoxy Resin top coat (Dräger Tweed). Carry using main body of valve, facing away from body. Store valve pointing down. From closed to fully open, no less than 2 full turns (3.5 Revolutions). Don’t Over Tighten Marked with cylinder re-test date. 300 bar 2454 litres air – 9ltr water capacity.(1.1 correction factor ) Pressure tested every 5 yrs with 20 year lifespan. Never completely drain cylinder, leave min of 2 bar in to prevent internal contamination & moisture ingress. Black & white quartering on shoulders denotes breathable air. 9 x 300/1.1 = 2454 Litres Cylinder Valise 300bar cylinder Re-enforcing strap at top Zip to close Carry handle Made from durable re-enforced plastic material Main valve Anti-debris tube (First Stage Filtration) Female threaded connector Main valve handle – pull & turn to close Copper anti debris tube Right angled cylinder valve NEXT

Cylinder: Working Pressure (bar) Water Volume (L) Cylinder serial number Red indicates the more relevant information Date of manufacture + 5# years… PREVIOUS NEXT

Bar Cylinder Calculations Drager 9 ltr Vol x 300 Bar = 2700 ltr 2700 x 0.9 ( correction factor ) = 2430 = 2430 50 ltrs Min Total Duration = 49 Mins Safety Margin - 12 Mins Working Duration = 37 Mins PREVIOUS MENU

Reducer Anti-tamper disk Longer Thread for 300 bar Built in Anti-vibration O-ring Spring loaded reducer mounting Pneumatic Whistle 2nd wearer ‘Y-Piece’ Pneumatics. First stage pressure reducer – Nickel Plated Brass, with inbuilt mechanical whistle. Reduces from 300 bar to 6 -9 bar. 10 year service life. Threaded hand wheel to connect to cylinder, finger and thumb only! Compression ‘O’ ring acts as anti-vibration device. (Inbuilt into hand wheel) Sintered bronze filter. 2 outlet ports, one high pressure, one medium pressure. (Medium pressure port incorporates pressure relief valve – hose lifts very slightly off its seating). 11-16 bars. Pneumatic whistle operates between 60 +/- 5 bars Electronic whistle in the bodyguard operates at 74 Bar (There will be some time delay between operation of both LPWW’s this is normal and due to the electronic monitoring unit detecting cylinder contents). O-Ring & Bronze Sintered Filter changed every 12 Months Choke screw set to 25L/Min Hoses. Flexible anti-kinking hose made from Ethylene-Propylene-Diene-Monomer (EPDM) rubber. Medium pressure travels from medium pressure port through a small ‘Y’ piece to the Demand Valve via female quick release coupling. From the other side of the ‘Y’ piece, there is a dual purpose hose for used for second wearer attachment High pressure travels from high pressure port to Electronic Monitoring Unit (EMU). From here there is a series of wires which are routed through a protective hose to the Body guard 7000. High pressure hose is different from medium pressure - inside it is a fine bore copper capillary tube coil wound round a multi-stranded phosphor bronze wire. Capillary tube and wire are brazed to each of the end fittings of the tube/wire assembly. High pressure air flows through the capillary tube. O-ring for pressure seal Bronze sintered filter MENU

Back Plate High strength light-weight carbon composite Pivoting/swivelling waist belt Fully adjustable yoke to 3 sizes (S,M,L) Built-in carrying handles Integrated electronics Integrated hoses Modular design NEXT

Back Plate Bodyguard Spring Clips size adjustment ( Gauge ) Spring Clips size adjustment Size Markings (S,M,L) Hose routed through back plate Battery release point Spring-loaded waist belt pivot point Backplate Two carrying handles. Moulded carbon composite, anti-static, lightweight & durable. Rubber buffer at base. 3 height shoulder yolk adjusted by two spring loaded buttons. Waist belt pivot slide assembly to improve weight distribution and freedom of movement. Twin hook reducer housing allowing reducer to pivot for ease of cylinder fitting. Bodyguard pressure module & Battery pack Battery ( A fully charged battery will last for 8 hrs ) PREVIOUS NEXT

Back Plate Carrying Handles LDV Auxiliary take off Reducer Housing Two carrying handles. Moulded carbon composite, anti-static, lightweight & durable. Rubber buffer at base. 3 height shoulder yolk adjusted by two spring loaded buttons. Waist belt pivot slide assembly to improve weight distribution and freedom of movement. Twin hook reducer housing allowing reducer to pivot for ease of cylinder fitting. Rubber Buffer Charging point PREVIOUS MENU

Harness: Neoprene rubber bonded to polyester fibre matrix High wear resistance Harness remains in position High temperature performance Material grips the wearers clothing and prevents slippage. NEXT

Harness Shoulder straps (designed to grip wearers PPE) Hose retaining flaps Cylinder strap with “camlock” buckle Spark-proof buckles Harness & Cylinder Strap. Two Neoprene Polyester photo luminescent hose retaining flaps with lift to spot locking studs. Quick release waist belt & shoulder straps constructed from flame retardant woven polyester wrap coated with flame retardant Neoprene. Trident clip buckle made from flame retardant Nylon. Universal cylinder strap made from 100% Navy Nomex. Camlock Buckle made from glass filled Nylon. All straps manufactured containing 50% Kevlar webbing meeting EN 137. Stainless steel spark-proof shoulder strap buckles. Designed to carry 2/3 weight on hips. Curved trident clip on waist belt assembly The shoulder and waist padding are manufactured using a compression forming process. The inner padding is produced from a flame retardant, closed cell, fully vulcanised foam. The inner liner is then covered with outer layers of woven polyester covered with Neoprene. The outer edges are covered with a stitched binding of the same material as the outer layer. Trident clip Quick release Waist belt assembly PREVIOUS NEXT

Harness Quick release shoulder harness and waist belt Quick assembly and disassembly Quick turnaround times in the workshop Easy cleaning Heavy duty stainless steel friction buckles Webbing will not twist within buckle Easy adjustment with gloves PREVIOUS MENU

Pneumatics Filter and ‘O’ ring replaced annually. Reducer exchanged every ten years. Reducer output 6-9 bar (dynamic & static pressures ) Reducer relief valve lift off pressure 11-16 bar. Choke screw set to 25 lts per minute. Pneumatic LPWW operates at 60 Bar + or – 5 Bar Whistle uses approx. 4 ltrs of air per minute. Positive pressure in mask between 0.1 and 0.3 bar above atmosphere… NEXT

Pressures 300 Bar – Nominal Charge (100%) 270 Bar – Minimum for full test (New Cylinder) (90%) 245 Bar - Minimum on completion of General test 240 Bar – Minimum Initial Entry (80%) 150 Bar – Minimum Re-entry (50%) 120 Bar – Minimum for Decontamination (40%) 74 Bar – Bodyguard LPWW (25%) 60 +/- 5 Bar – Pneumatic (failsafe LPWW) (20%) Any rounding up or down of figures are within the tolerances Bar Pressure x Water Vol. / 1.1 = Remaining volume of air (– 600l for safety margin) Consumption rate 50l/min Remaining vol. / consumption rate = Time remaining to whistle 150 bar calculated to give 12 minutes before TOW. 120 bar calculated to give just under 8 minutes before TOW. 74 bar is calculated to give a 12 minute safety margin. 60 Bar gives a 9.8 minute safety margin and is set by Draeger as a failsafe should the Bodyguard fail we still have a LPWW PREVIOUS MENU

Lung Demand Valve (LDV) LDV Release Buttons Re-set button Swivel coupling Lung Demand Valve. ESA Coupling to FPS 7000 Face Mask Two spring-loaded release buttons (depress together to release from mask Fitted with medium pressure hose via a swivel coupling at one end to male instantaneous coupling at the other. Made from moulded glass filled nylon. Demand valve re-set button and supplementary supply button. Medium pressure is reduced to a breathable level, which fluctuates as wearer inhales and exhales but will always remain in positive pressure during breathing cycle. Green reset button denotes CBRN compliant materials Constant flow switch MENU

FPS 7000 Face Mask 5 Point head harness attachments Polycarbonate Visor Voice Enhancement power button on R/H side Mask body LDV Port Inner Mask (orinasal) Exhalation Valve Mushroom Valve Voice Enhancement Speaker    FPS 7000 face mask. (Fire fighter Protection System). Small, medium & large sizes available. Ethylene-Propylene-Diene-Monomer (EPDM) rubber. Polycarbonate visor where the outside is scratch resistant and the inside is anti-fog, it also has ballistic protection at extreme temperatures. Held in place by upper & lower lens frames. 5 point head harness constructed from chloroprene & neoprene. Double reflex seal. Inner mask with 2 inhalation valves. The inner mask is also cut away at the bottom for better drainage. Reduces dead space and allows air to flow over the visor. Integrated comm’s speaker PTT Button Radio connection MENU

Bodyguard 7000 Digital pressure reading Radial segments pressure and timing Right hand button Left Hand button Time to whistle Distress alarm button BODYGUARD 7000(T) & ELECTRONIC MONITORING UNIT (EMU) ● Integrated Electronic Monitoring Unit (EMU) ● Comprises of an Electronic Pressure Transmitter Module, a Display Unit and a Powerpack ● A short High Pressure Hose, routed from the High Pressure Sensor housing of the EPTM; This connects to the High Pressure outlet of the Pressure Reducer valve. ● The Display Unit features a digital screen, it has a multi functioning system and incorporates the following: Available Pressure TTW Visual LED’s Motion Sensor and Automatic DSU Battery Life Backlight feature Personal ID – Not used by KFRS   ● Power Supply is 7.5 Volts, which is powered by 5 x 1.5 Volt AA batteries. Replaced annually or if low battery warning is displayed on Bodyguard user interface. Low Battery warning displayed when 2 hours of battery life left. Blue, Red & Green LED’s ADSU Tally key Hose/Cable assembly to electronic pressure transmitter module NEXT

Bodyguard 7000 Provides continuous monitoring of the SCBA. ( GREEN LED flashes every second when bodyguard is in operation, When linked to Merlin Board two additional BLUE LEDs flash intermittently ) Monitoring of the cylinder pressure. ( Digital reading updated every 20 seconds ) Time to whistle (TTW). Digital reading. Button activated Distress Signal Unit. ( DSU 96-105 db )... PREVIOUS NEXT

Bodyguard 7000 Movement sensor and Automatic Distress Signal Unit. (If no movement detected after 30 seconds a pre-alarm will sound, if no movement after a further 15 seconds full alarm sounds with 2 RED & 2 BLUE LEDs flashing intermittently) Back light feature. (On pressing either Left or Right button the body guard unit will illuminate the display for 3-5 seconds) Electronic Whistle Warning Unit. (Electronic whistle will operate at 74 Bar , 90 db) PREVIOUS MENU

(Close Cylinder wheel and vent Air Supply) Log Off A – AIR SUPPLY (Close Cylinder wheel and vent Air Supply) B – BODYGUARD (allow gauge to read ZERO, bodyguard will automatically turn off within 20 sec ) C – COMMSa (Switch off comms ; radio & speech enhancer) This will ensure that the set has logged off from the Merlin board MENU

Any Questions MENU