Impact Wrenches Available in 3/8, 1/2 and ¾ inch drive.

Slides:

Advertisements

Similar presentations

Measuring and Testing Instruments

Advertisements

Basic Small Engine Maintenance and Repair Projects

“The Strength of Experience”

Tools and Functions R7AxwS3BnU.

 Wear proper eye protection, ear protection, and protective clothing.  Secure hair and loose clothing.  Work in areas with good lighting.  Make sure.

Clutch Fundamentals Chapter 69.

Engine Cylinder Leakage Test Tune 8 NATEF Section A8, A.11 P-1.

Tools and Measuring Instruments

Model 12 Intek Horizontal OHV

Lesson 3 Measuring Engine Components and Specifications.

New Mexico FFA Agricultural Mechanics Career Development Event Engine Power.

Model 12 Intek Horizontal OHV Crankcase Disassembly and Assembly Lab #7.

BASIC HAND TOOLS OPEN END WRENCH BOX END WRENCH.

REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.

Copyright © 2007 by Nelson, a division of Thomson Canada Limited. 6-1Chapter 6 Prepared by Martin Restoule Algonquin College Diagnostic Equipment and Special.

CARBURETED FUEL SYSTEM

Tool Identification Power Technology. Standard Screw Driver.

Preventative Maintenance & Troubleshooting

New Mexico FFA Agricultural Mechanics Career Development Event Engine Power.

© 2011 Pearson Education, Inc. All Rights Reserved Automotive Technology, Fifth Edition James Halderman IN-VEHICLE ENGINE SERVICE 27.

1 Basic Hand tools Basic Tools. 2 3 Objectives Upon completion of this class and activities, you will be able to: –Recognize basic hand tools. –Identify.

Lesson No. 09 Week No. 05 Lesson Name Reamer. REAMER Use:- Reamer is used enlarging by finishing previously drilled hole to accurate size. Material:-

I.C. ENGINES Practical No: 1 (17 Mar, 2014). Measurement of Cylinder Pressure If your vehicle has been running roughly or losing power, there may be a.

Tools & Measuring Instruments

Measuring Engine Components and Specifications

Chapter 9 Hand Tools. chapter 9 Hand Tools FIGURE 9.1 A forged wrench after it has been forged but before the flashing, extra material around the wrench,

Hand Tools. 1. Adjustable Wrench Adjustable Wrench Turning various size nuts and bolts.

Hand Tools. Tool vocabulary 1. Ratchets11.Ball peen hammer 21.Lug wrench 2. 1tubing wrench 12.Phillips/standard screw driver 22.Feeler Gauge 3. 2pt.&

Unit 1.5 Hand Tools All Students must know their tools.

Unit A 6-3 Mechanical Systems and Technology. Problem Area 6 Agricultural Power Systems.

Model 12 Intek Horizontal OHV Carburetor Disassembly & Assembly Lab #3.

Measuring Engine Components and Specifications. Next Generation Science/Common Core Standards Addressed! CCSS.ELA Literacy.RST.9 ‐ 10.3 Follow precisely.

Automotive Brake Systems, 5/e By James D. Halderman Copyright © 2010, 2008, 2004, 2000, 1995 Pearson Education, Inc., Upper Saddle River, NJ All.

Note location of different length bolts

+ The Four Stroke Cycle By Elizabeth Fahey. + Outline Time Required: 1-3 classes Grades: 9-12 Background: Lesson is in conjunction with the small engine.

Engine Reassembly Technicians need to take their time when reassembling an engine. This is not a race! Listen for instruction when to add the next piece.

Model 12 Intek Horizontal OHV

Lesson 3 Measurement Tools used in measuring engine components Micrometer caliper – precision measuring tool for taking outside measurements. Inside.

1 Flywheel 2 Connecting Rod 3 Valve 4 Primer 5. Timing Gear.

Auto Mechanics Tools Piston Ring Compressor.

Automotive Engines: Theory and Servicing, 6/e By James D Halderman © 2009 Pearson Education, Inc. Pearson Prentice Hall - Upper Saddle River, NJ

1 Spark Plugs. 2 Spark Plugs ignite the air fuel mixture in the engine. ≈10,000 volts jump the gap between the center electrode & the ground electrode.

1 Engine Mechanical Labs R. Bortignon. 2 Repair Information – essential! locate model number!

By John Templeton.  Definition- the science that deals with the laws governing water or other liquids in motion and their applications in engineering;

SAFE WORK PRACTICES IN AGRICULTURAL MECHANICS AG MECH II.

Tool List. Open-End Wrench Box-End Wrench Combination Wrench.

© Goodheart-Willcox Co., Inc.. Purchase Quality Tools  With tools, you usually get what you pay for  Quality tools are lighter, stronger, easier to.

REV AUTO SHOP FINAL. 1. If you owned a Toyota car and an early model Chevy truck, what types of wrenches and sockets should you purchase? US standard.

6832 –7.00 Proper use of tools Handle Files should have a ______ to prevent hand injuries.

Pistons and piston rings

CH 6.5 Electric Power Tools.

Automotive Engines Theory and Servicing

BASIC GAS METAL ARC WELDING

Automatic Transmissions and Transaxles

Clutch Fundamentals.

Small Engine Disassembly

IN-VEHICLE ENGINE SERVICE

Tools of the Trade Contren #

Combination pliers.

Tools of the trade.

Ignition Systems Overview

Cylinder Head: Parts and Service

Agricultural Mechanics Career Development Event Engine Power

AUTOMOTIVE TOOL IDENTIFICATION

Servo Pilot SFP-150 to 1500.

Automotive Engines Theory and Servicing

Hand and Power Tools This presentation will explore:

Presentation transcript:

Impact Wrenches Available in 3/8, 1/2 and ¾ inch drive.

Compression Gauge Ranges from 0 to 300 pounds.

Battery Pliers Used for removing battery terminals. The end clearance prevents cell-cover damage.

Power Timing Light Operates on 6 or 12 volt DC producing a blue-white flash for reading of timing mark.

Spark Plug Gauge Set Usually ranges from.020 to.040 thick wire sizes.

Torque Wrench Comes in 1/4, 3/8, 1/2, and ¾ inch drives.

Retaining Ring Pliers User for remove and install internal and external retaining (snap) rings.

Tachometer Useful for checking speed on tools, machines, and engines.

Expansion or Adjustable Reamer Used for reaming piston pin holes, king pin holes, holes for water pump bushings, valve stem guides and other precision reaming jobs.

Air Pressure Type Grease Gun It is portable but must be attached to an air line.

Lever Type Grease Gun It is filled by hand, cartridge, or from an air pressure gun.

Zerk Grease Fitting This fitting will withstand high pressure. The grease gun "snaps on" to the fitting.