Security Speed A utomatic S ource T ransfer < 8 Cycles < 150ms.

Slides:



Advertisements
Similar presentations
1 UNIT I (Contd..) High-Speed LANs. 2 Introduction Fast Ethernet and Gigabit Ethernet Fast Ethernet and Gigabit Ethernet Fibre Channel Fibre Channel High-speed.
Advertisements

Network Hardware and Physical Media
Network Devices Repeaters, hubs, bridges, switches, routers, NICs.
Introduction to Network
Chapter 3: Planning a Network Upgrade
Topic 7 Local Area Networks (LAN)
MFS, MPO 4/8/12-Fiber connectors and Fan-Out assemblies.
A Very Basic Fiber Optic Tutorial (Not A Dummy’s Guide to Fiber Optics!)
Structured Network Cabling CIS 399 Day 1, Morning Session 2 Dale Smith University of Oregon & NSRC
Optical communications & networking - an Overview
Chapter 4 Circuit-Switching Networks
Prepared by:Mohammed Ayesh
Shalini Bhavanam. Key words: Basic Definitions Classification of Networks Types of networks Network Topologies Network Models.
Department of Computer Engineering University of California at Santa Cruz Networking Systems (1) Hai Tao.
Fiber-Optic Communications
Fiber Optics FIBER CONNECTOR TYPES.
Many Roads To Home. LAN Roads UTP STP Coaxial Fiber Optics.
DataLink Layer1 Ethernet Technologies: 10Base2 10: 10Mbps; 2: 200 meters (actual is 185m) max distance between any two nodes without repeaters thin coaxial.
Connecting LANs, Backbone Networks, and Virtual LANs
Chapter 11 Extending LANs: Fiber Modems, Repeaters, Bridges, & Switches Hub Bridge Switch.
SPLICING OF FIBER CABLE
Chapter 6 High-Speed LANs Chapter 6 High-Speed LANs.
TC 361 Data Networking Test Review
Carrier Networks (Chapter 4) Long Haul/Core Network Metro Network Access Network Technologies Convergence Signaling Digital Hierarchy/SONET.
NETWORK CABLING Chapter 2
Network Access and Transmission Methods Chapter 10.
Virtual LAN Design Switches also have enabled the creation of Virtual LANs (VLANs). VLANs provide greater opportunities to manage the flow of traffic on.
Chapter 8 Help is here!. Cabling Whenever you need cabling that will protect your signal from electrical interference there is only one correct answer:
Wan Technologies. OSI Model Do a quick internet search to find a good picture of an OSI model.
Chapter 5 Switching. Introduction Look at: –Bridges and Bridging(5.1) –Switches and Switching(5.2) –Spanning Tree Algorithm(5.3) –Virtual Local Area Networks.
1/28/2010 Network Plus Network Device Review. Physical Layer Devices Repeater –Repeats all signals or bits from one port to the other –Can be used extend.
Repeaters and Hubs Repeaters: simplest type of connectivity devices that regenerate a digital signal Operate in Physical layer Cannot improve or correct.
Chapter 6 Wide Area Networking Concepts, Architectures, & Services.
Intorduction to Lumentis
Campus Network Best Practices: Structured Cabling Dale Smith University of Oregon/NSRC This document is a result of work by the Network.
Mr. Mark Welton.  A computer network, or simply a network, is a collection of computers and other hardware interconnected by communication channels.
Module 8: Ethernet Switching
Data and Computer Communications Circuit Switching and Packet Switching.
Cisco 3 - LAN Perrine. J Page 110/20/2015 Chapter 8 VLAN VLAN: is a logical grouping grouped by: function department application VLAN configuration is.
1 CHAPTER 8 TELECOMMUNICATIONSANDNETWORKS. 2 TELECOMMUNICATIONS Telecommunications: Communication of all types of information, including digital data,
Review: –Ethernet What is the MAC protocol in Ethernet? –CSMA/CD –Binary exponential backoff Is there any relationship between the minimum frame size and.
Click to edit Master subtitle style
Campus Network Best Practices: Structured Cabling Dale Smith University of Oregon/NSRC This document is a result of work by the Network.
Cisco S3C3 Virtual LANS. Why VLANs? You can define groupings of workstations even if separated by switches and on different LAN segments –They are one.
Computer Networking Dinesh Kumar Ram PGT Comp.Sc. KV NAD Aluva.
Chapter 3 - VLANs. VLANs Logical grouping of devices or users Configuration done at switch via software Not standardized – proprietary software from vendor.
Cisco Network Devices Chapter 6 powered by DJ 1. Chapter Objectives At the end of this Chapter you will be able to:  Identify and explain various Cisco.
McGraw-Hill©The McGraw-Hill Companies, Inc., 2004 Connecting Devices CORPORATE INSTITUTE OF SCIENCE & TECHNOLOGY, BHOPAL Department of Electronics and.
Oz – Foundations of Electronic Commerce © 2002 Prentice Hall Essentials of Telecommunications.
Optical Fiber & OF Cables.
 Describe the basic and hybrid LAN physical topologies and their uses, advantages, and disadvantages  Describe the backbone structures that form the.
© ExplorNet’s Centers for Quality Teaching and Learning 1 Select appropriate hardware for building networks. Objective Course Weight 2%
Application Note Fiber Connectivity Riedel solutions for broadcast applications 1 Application Note - Fiber Connectivity.
3 Fiber-Optic Cable Permission granted to reproduce for educational use only.© Goodheart-Willcox Co., Inc. Objectives  Explain how fiber-optic cable.
Connectors, Repeaters, Hubs, Bridges, Switches, Routers, NIC’s
Network Devices Repeaters, hubs, bridges, switches, routers, NIC’s.
Network Access and Transmission Methods
Instructor Materials Chapter 1: LAN Design
Optical-Based Switching Solutions
Lab 2 – Hub/Switch Data Link Layer
Chapter 4 Data Link Layer Switching
Introduction to Computers
Lab 2 – Hub/Switch Data Link Layer
PON Extra Material.
Ethernet LAN 1 1.
Flexible Transport Networks
Fall 2013 Networking Presentation
Optical communications & networking - an Overview
Connecting Devices Hosts and networks do not normally operate in isolation Connecting devices connect hosts together to make a network or connect networks.
Connectors, Repeaters, Hubs, Bridges, Switches, Routers, NIC’s
Presentation transcript:

Security

Speed A utomatic S ource T ransfer < 8 Cycles < 150ms

Build an asset Fiber has a 20 year + life Any excess fiber can be leased or sold

 Multimode Fiber ◦ Large Core most common 62.5um ◦ Only good for < 4KM  Single Mode Fiber ◦ ITU-T G.652-Zero Dispersion around 1310 nm\ ◦ Supports CWDM and DWDM and Standard Ethernet  Dispersion Compensated Fiber ◦ ITU-T G.655-Zero Dispersion around 1550 nm ◦ Supports DWDM and Standard nm ◦ Support Long Spans 50 KM+

Loose Tube Fiber ◦ Commonly used in lashed or under ground deployments. ◦ Has very little internal support. ◦ Fiber loose in buffer tubes to allow for temperature and moisture change. Armored Fiber ◦ Loose tube fiber with corrugated steel Armor ◦ Must be grounded

◦ ADSS(All-Dielectric Self-Supporting)  Support and span length engineered into fiber  No grounding requirements  Installed using Pulleys Dead End with Slack

ADSS Minimum Bend Radius To arrive at a working bend radius for cable installation, multiply 20 times (20 x) the cable outside diameter. Cable Diameter = 0.46 in (11.8 mm) Example: 20 x 0.46 in = 9.2 in (177 mm) Minimum Working Bend Radius = 9.2 in (17.7 cm) To find the minimum diameter requirement for pull wheels or rollers, simply double the minimum working bend radius:

ADSS Tensions As temperature increases ADSS tension will also increase. This is opposite of ACSR (conductor) Incorrect tension can damage fiber over time

Single mode starts at $.25/foot

Ribbon Fiber  Efficient packaging of higher fiber counts  Lightweight and easy to handle during installation  Specialized Splicers to splice 12 Fiber simultaneously

 Optical Ground Wire (OPGW) ◦ Fiber optics engineered into ground wire(Shield) ◦ Wire and Fiber must be Pre-engineered for access of fiber optics( No access mid span) ◦ Lower cost than underground

Core Alignment Splicer Uses Servos and Camera to align core Very precise low loss splice Electrical Arc fuses Glass Must be cleaved V Groove Splicer Less Precise Lower cost to purchase and maintain Must be cleaved

Dome enclosures High Capacity enclosure Customizable using grommets Splice trays separate Typically used for butt connections Low Count enclosures Compact Size Low splice capacity Inline or Butt splices

ADSS Dead Ends Used to make high angle turns Must use for slack storage Creates Shear points Tangents Supports fiber between dead ends Line angle limitation < 20 degrees Some models can be used in pulling short spans 1. Keeper 2. Cushion Inserts (With or Without Grit) 3. Captured Bolt and Washer (Captured with Grommet) 4. Lock Nut 5. Anchor Shackle with Eye-nut (Optional not shown) 6. Structural Reinforcing Rods (optional, not shown)

 Lashed Fiber Fiber lashed to steel carrier Must be grounded Can not be installed in power space

SC (Subscriber Connector) Square connector Push-Pull snap LC (Lucent/little connector) Small high density Snap fit Used on Lasers(XFP/SFP) ST (Straight Tip) Round Twist lock Common in Sub Stations UPC (Ultra Physical Contact) polish style of fiber optic ferrules Standard for most applications APC (Angled Physical Contact) Has Lower lightwave reflectance Used in RF optical applications

Passive One Fiber 32 to 64 Customers Requires optical Splitters Bandwidth is Shared Active One Fiber One Customer Bandwidth not shared Requires high fiber counts Non Powered Optical splitter

 Sonet (Synchronous Optical Network)  Based on older Time Division Multiplexing T1-T3 Technology  Poor bandwidth Efficiency(Protection Path No bandwidth) Limited bandwidth sizes  Sub 50ms protection  High Deployment cost Active Path Reserved path No activity

 Ethernet ◦ Low Cost Deployment ◦ Flexible bandwidth rates ◦ Sub 50ms protection without stranding bandwidth ◦ Mesh and Ring Topologies ◦ Easily Scalable Active Path Secondary path Active Path

DWDM Multiplex up to 160 channels of bandwidth on 2 fibers Capable of long distance communications Wavelength sizes up to 100Gb Can use a digital wrapper(OTN) to encapsulate many types of data and maintain packet quality Most systems do not have protection

Standard Ethernet DWDM TXRCV TXRCV

 Layer 2 (Facts) 1. Switching determined by MAC address database 2. If Packet Collision occurs, packet randomly retries 3. Packet Broadcast transverses all switches on domain 4. Vlans provide segmentation of domain 5. Vlans also allow for security and network traffic flow management

A B C D Layer 3 Router Layer 2 Switch Vlan 10 Sub A Vlan 20 Sub B Vlan 30 Sub C Vlan 40 Sub D Ethernet Ring Block G IPs terminated on Router Vlan 10= /27 Vlan 20= /27 Vlan 30= /27 Vlan 40= /27 29 usable IPs per Vlan / / /27

1.ITU G.8032 provides a method of ethernet protection while preventing loops. 2.Master node blocks traffic on one interface of ethernet ring 3.Failover achieved in less than 50ms 4.Many derivatives of this technology that are proprietary (Nodes must be of same Manufacture and same Firmware)

Layer 3 (Facts) 1. Network Control by routing IP address 2. No problems controlling Broadcast domains 3. Control Services and bandwidth based on IP subnets 4. Ring and Mesh redundancy available 5. Traffic flooding and storming easy controlled 6. Most Layer 3 devices support layer 2

A B C D Layer 3 Switch/Router Ethernet Ring Block G IPs terminated on Router Vlan 10= /30 Vlan 20= /30 Vlan 30= /30 Vlan 40= /30 2 usable IPs per segment / / /27 L ayer 2 Ring Traffic controlled by static or Dynamic routing MESH Topology

 MPLS packets transverse fiber node based on shortest path and label  MPLS allows transport of ATM, Sonet and Ethernet  VPLS (Virtual Private Lan Service) allow for layer 2 type connectivity with layer 3 controls  While running MPLS switch processor and QOS are easily controlled per vpls instance  Availability of complex traffic engineering

A B C D Layer 3 Switch/Router Ethernet Ring Block G L ayer 2 Ring Traffic controlled by Labels VPLS creates layer 2 connectivity Fiber Cut MPLS Restores Path

OTDR optical time-domain reflectometer Used to test quality and length Shows projected fiber loss Find fiber optic breaks

OTDR Output

Single-mode/Multimode Loss Test Kit Measure true loss of fiber Fiber identification Certify Fiber for Sale/IRU Optical Fiber Identifier Fiber Identification Power Meter and Direction

Features no other SCADA protocol has had before... Self-description and browsers Structured data Device models, not data points Capability for access security Fast peer-to-peer communications Dramatic reduction of necessary wiring Powerful reporting features A wide choice of lower layers

 What is the Purpose of the Network ?  What is the necessary capacity ?  How critical is the DATA transport ?  What types of DATA do I wish to transport ?  What is the future plans for the Network ?  Will We transport public DATA ?  What security levels do I need ??

Thank You Billy Wise