Scale Drawings Today you will learn to: identify similar figures

Slides:

Advertisements

Similar presentations

5.7 Scale Drawings and Models

Advertisements

SCALE FACTORS MODELS & MAPS In addition to level 3.0 and above and beyond what was taught in class, the student may: · Make connection with other.

Scale Drawings Matchbook Definitions: MG 1.2 Construct and read scale drawings MG 1.3 Use measures expressed as rates. Purpose and Rationale: Students.

Quiz Use the properties of similar figures to answer 1 and 2:

Bell Quiz. Objectives Learn to write and solve problems using proportions.

Unit 6: Scale Factor and Measurement

Scale Drawings.

Learning Target I can use proportional reasoning to solve scale drawing problems.

Similar Shapes and Scale Drawings

What will I learn today? Learn to understand ratios and proportions in scale drawings. Learn to use ratios and proportions with scale.

Pre-Algebra 7-7 Scale Drawings HW: Page 370 #1-6 and #21-26.

Pre-Algebra 7-7 Scale Drawings Learn to make comparisons between and find dimensions of scale drawings and actual objects.

Estimating Measurements 5.1a Estimate the area of irregular shapes, angle measurement, or weight of common objects 5.2a Estimate, make and use direct and.

6.2 – Use Proportions to Solve Geometry Problems

Geometry Notes Lesson 4.3B – Similarity and Scale Drawings T.2.G.1 Apply congruence (SSS …) and similarity (AA …) correspondences and properties of figures.

Geometry with Cosby Missy Cosby Okemos High School Math Instructor.

Scale Drawings & Proportions

Use scales to find missing parts: maps blueprints models

Surface Area and Volume

4-2(B) Scale Drawing.

7-4 Scale Drawings p  Indicator – M4 Solve problems involving scale factors.

Find Actual Measurements

Lesson 17 Using Scale Drawings. Scale Drawings Scale drawings and scale models make it possible to show objects accurately that are either too large or.

All scale drawings must have a scale written on them. Scales are usually expressed as ratios. Normally for maps and buildings the ratio: Drawing length:

Target: Use proportions to solve problems involving similar figures.

2 pt 3 pt 4 pt 5pt 1 pt 2 pt 3 pt 4 pt 5 pt 1 pt 2pt 3 pt 4pt 5 pt 1pt 2pt 3 pt 4 pt 5 pt 1 pt 2 pt 3 pt 4pt 5 pt 1pt Proportions Similar Figures PercentsApplications.

BLUEPRINT READING FOR CABINETMAKERS. PICTORIAL DRAWINGS.

Holt CA Course 1 5-8Scale Drawings and Scale Models NS1.3 Use proportions to solve problems (e.g., determine the value of N if T =, find the length of.

Scale Drawing and Models

Scale Drawings and Models

Scale Drawing - a two dimensional drawing that is similar to the object it represents. Scale Model - a three-dimensional model that is similar to the object.

Extension 3.6 Proportions and Similar Figures A.What do you know about similar triangles and congruent triangles? B.Definitions 1.Similar triangles – have.

 Two figures are similar if…  1.) Their corresponding angles are congruent  2.) The corresponding sides are PROPORTIONAL!!! 5 in A B C D 4 in 10 in.

Defining Success For Bigger or Smaller In this lesson we will: NxG M.7.G.1 - Solve problems involving scale drawings of geometric figures, including:

2.8 – Proportions & Similar Figures “I can solve proportions using scale factors.” “I can find missing side lengths of similar figures.”

Gateway – Unit 7 – Green Architecture

Dimensioning 1’ - 8” 8’ - 4” Unit 8.

Scale Drawings. Scale – The ratio that compares the measurements of the real object and its model. EX: 1 in = 6 ft Scale factor – written as a ratio without.

6.2 Use Proportions to Solve Geometric Problems Goal:You will use proportions to solve geometry problems.

6.2 USE PROPORTIONS TO SOLVE GEOMETRIC PROBLEMS Goal:You will use proportions to solve geometry problems.

Chapter 6.2 Notes: Use Proportions to Solve Geometry Problems Goal: You will use proportions to solve geometry problems.

6.2 Use Proportions to Solve Geometry Problems Hubarth Geometry.

GEOMETRY HELP Circle A with 3-cm diameter and center C is a dilation of concentric circle B with 8-cm diameter. Describe the dilation. The circles are.

FINDING VOLUME USING FORMULAS Volume. Find the Volume! Find the volume of the rectangular prism below: V = ______cubic units.

PreAlgebra Farris * I can use scale drawings and construct scale drawings.

 2.5: Similar Figures. What is a Similar Figure?  Figures that have the same shape, but not necessarily the same size.  Two figures are similar when:

Area and Perimeter of Similar Figures

Objectives Use ratios to make indirect measurements.

A man who is 6 feet tall is standing near a cactus

Similar Polygons.

Scale Drawings Bell Ringers

Scale and use scale drawings to solve problems.

Maps and scale drawings are:

Use Proportions to Solve Geometry Problems

A scale drawing is a drawing in which all parts of the drawing are reduced or enlarged by the same scale factor. A scale is a ratio that compares the measurements.

Proportions Rachel Wraley.

ALGEBRA I - SECTION 2-8 (Proportions and Similar Figures)

Chapter 3: Solving Equations

AIM 7-5: How can we use ratios to make indirect measurements?

Goal: The learner will use proportions to find measures of objects.

Insert Lesson Title Here

HW L10-3 pg 392 #8-14 L10-3 Notes: Scale Drawings and Models

Study Island Homework Due Friday Maintenance Sheet 18

Homework- Due Friday- Study Island- Maintenance Sheet 18

6.2 Use Proportions to Solve Geometric Problems

Homework- Study Island- Due Friday & Parent Letter Due

Homework- Maintenance Sheet 18 Due Friday- Goformative. com

Presentation transcript:

Scale Drawings Today you will learn to: identify similar figures solve problems involving scale drawings of geometric figures, including finding length. M07.C-G.1.1.1: Solve problems involving scale drawings of geometric figures, including finding length and area.

Scale Drawings

Scale: Example

Blueprints

Blueprints: Example The following blueprint of a kitchen has dimensions of 7 inches by 7 inches. The island has been highlighted in red. The island's actual dimensions are 2 5/8 feet by 1 5/16 feet. If the scale of the blueprint is 1 inch = 3 feet, what are the dimensions of the island on the blueprint?