Chapter 12. Direct Synthesis ( G includes G m, G v ) 1. Specify closed-loop response (transfer function) 2. Need process model, (= G P G M G V ) 3. Solve.

Slides:



Advertisements
Similar presentations
Controller Design Based on Transient Response Criteria
Advertisements

PID Controllers and PID tuning
Discrete Controller Design
Enhanced Single-Loop Control Strategies
Chapter 6.1 Common Core – A.REI.6 Solve systems of linear equations exactly and approximately, focusing on pairs of liner equations in two variables. Objectives.
Ratio Control Chapter 15.
Nyquist Stability Criterion
Process Control: Designing Process and Control Systems for Dynamic Performance Chapter 19. Single-Loop IMC Copyright © Thomas Marlin 2013 The copyright.
Nise/Control Systems Engineering, 3/e
Solving Equations = 4x – 5(6x – 10) -132 = 4x – 30x = -26x = -26x 7 = x.
CHE 185 – PROCESS CONTROL AND DYNAMICS
Control System Design Based on Frequency Response Analysis
Enhanced Single-Loop Control Strategies
Chapter Summer 2. Comparator 3. Block Blocks in Series
Dynamic Behavior and Stability of Closed-Loop Control Systems
Controller Tuning: A Motivational Example
Dynamic Behavior and Stability of Closed-Loop Control Systems
Chapter 11 1 Closed-Loop Responses of Simple Control Systems In this section we consider the dynamic behavior of several elementary control problems for.
Vocabulary Chapter 6.
Solving Systems of three equations with three variables Using substitution or elimination.
Block Diagram Reduction SUBMITTED BY: Mrs. RAMANDEEP KAUR ASSOT. PROFESSOR-EEE.
Introduction to Industrial Control Systems
Write and graph a direct variation equation
Control System Design Based on Frequency Response Analysis
Anis Atikah Ahmad CHAPTER 11: Dynamic Behaviour & Stability of Closed-Loop Control Systems Anis Atikah Ahmad
Cascade and Ratio Control
3x – 5y = 11 x = 3y + 1 Do Now. Homework Solutions 2)2x – 2y = – 6 y = – 2x 2x – 2(– 2x) = – 6 2x + 4x = – 6 6x = – 6 x = – 1y = – 2x y = – 2(– 1) y =
3.5 – Solving Systems of Equations in Three Variables.
Control Engineering Application
DYNAMIC BEHAVIOR AND STABILITY OF CLOSED-LOOP CONTROL SYSTEMS
Chapter 8 Model Based Control Using Wireless Transmitter.
Controller Design (to determine controller settings for P, PI or PID controllers) Based on Transient Response Criteria Chapter 12.
PID Controller Design and
Prof. Wahied Gharieb Ali Abdelaal CSE 502: Control Systems (1) Topic# 3 Representation and Sensitivity Analysis Faculty of Engineering Computer and Systems.
Chapter 7 Adjusting Controller Parameters Professor Shi-Shang Jang Chemical Engineering Department National Tsing-Hua University Hsin Chu, Taiwan.
CHAPTER 12: Controller Design, Tuning, & Troubleshooting
Section 5.3 Solving Systems of Equations Using the Elimination Method There are two methods to solve systems of equations: The Substitution Method The.
7.4. 5x + 2y = 16 5x + 2y = 16 3x – 4y = 20 3x – 4y = 20 In this linear system neither variable can be eliminated by adding the equations. In this linear.
Chapter - Continuous Control
Review. Feedback Terminology In Block diagrams, we use not the time domain variables, but their Laplace Transforms. Always denote Transforms by (s)!
Solving a System of Equations in Two Variables By Substitution Chapter 8.2.
SOLUTIONS ERT 321 Process Control & Dynamics Anis Atikah binti Ahmad EXERCISE 3.
Review after Christmas!. Solve the below equations for the variable..5 (6x +8) = 16 1.
The Substitution Method Objectives: To solve a system of equations by substituting for a variable.
SOLVING SYSTEMS OF EQUATIONS BY SUBSTITUTION. #1. SOLVE one equation for the easiest variable a. Isolated variable b. Leading Coefficient of One #2. SUBSTITUTE.
Notes 6.5, Date__________ (Substitution). To solve using Substitution: 1.Solve one equation for one variable (choose the variable with a coefficient of.
Anis Atikah Ahmad CHAPTER 11: Dynamic Behaviour & Stability of Closed-Loop Control Systems Anis Atikah Ahmad
Chapter 11 1 ERT 210/4 Process Control CHAPTER 11 DYNAMIC BEHAVIOR AND STABILITY OF CLOSED-LOOP CONTROL SYSTEMS.
Dead Time Compensation (Smith Predictor)
Solving Linear Systems
Systems of Equations can be linear or non-linear
Block Diagram Reduction
Chapter 12 Section 1.
Controller Tuning: A Motivational Example
Solving Equations by Factoring and Problem Solving
Section 2 – Solving Systems of Equations in Three Variables
Ch 4.4: Variation of Parameters
Factor and Solve Polynomial Equations
Homework 1: Electrical System
Problems of the Day Express the relation {(–3, 4), (–1, 2), (–3, 3), (2, 4) (4, 3)} as a table, as a graph, and as a mapping diagram. State the Domain.
Solving One-Step Equations
Solving systems using substitution
Solving Equations with Variables on Both Sides
Solving Equations with Variables on Both Sides
Warm Up 12/3/2018 Solve by substitution.
Proportional Control and Disturbance Changes
6 minutes Warm-Up 1. Find the slope of the line containing the points (-2,5) and (4,6). 2. Find the slope of the line y = x – Find the slope of the.
PID Controller Design and
Solving a System of Linear Equations
Balanced scales and equations
Presentation transcript:

Chapter 12

Direct Synthesis ( G includes G m, G v ) 1. Specify closed-loop response (transfer function) 2. Need process model, (= G P G M G V ) 3. Solve for G c, Chapter 12 (12-3b)

Specify Closed – Loop Transfer Function (first – order response, no offset) But other variations of (12-6) can be used (e.g., replace time delay with polynomial approximation) Chapter 12

Derivation of PI Controller for FOPTD Process Consider the standard first-order-plus-time-delay model, Substituting and rearranging gives a PI controller, with the following controller settings: Chapter 12 Specify closed-loop response as FOPTD (12-6), but approximate

Chapter 16 Time Delay Compensation Model-based feedback controller that improves closed-loop performance when time delays are present Effect of added time delay on PI controller performance for a second order process (  1 = 3,  2 = 5) shown below

Chapter 16

No model error: (sensitive to model errors > +/- 20%) Chapter 16

Direct Synthesis Approach (Smith Predictor) Assume time delay between set-point change and controlled variable (same as process time delay,  ). If then From Block Diagram, Equating... Chapter 16