Finally, a compressed air piping system so simple…it’s EZ!

What is EZAir ? Low cost aluminium piping system –Higher flow rates –Safe, secure, and leak proof –Reduced pressure loss Simple push to connect fittings –Easy to install piping –Easy to reconfigure system

EZAir Markets For all compressed air systems downstream of the air receiver Small to medium body shops Light industrial manufacturing and assembly Dealers/resellers

Selling advantages of EZAir Cost, Cost, Cost Ease of installation No skill needed Little tooling needed (only pipe cutter) Very light Very fast to install

EZAir Fittings Manufactured from high quality acetal plastic or brass Small line of items that easily meet any requirement –Only 22 items in total product line Simple for distributors to carry a full range of low cost inventory

EZAir Fittings 15mm and 22mm Range Straight Union Elbows Tees Water Trap Tee (22mm) Stem Elbow Straight Reducer Brass Stem Adaptors Pipe Clips & Spacers Brass Wing Back (15mm)

EZAir Fittings 28mm Range Straight Union Elbows Tees Water Trap Converter Brass Stem Adaptor Plugs Pipe Clips & Spacers

22mm Water Trap Tee Applications High air quality Systems without dryers Will reduce condensate at point of use Should not be used in place of a dryer

28mm Water Trap Tee Converter Fits into standard 28mm Tee Same applications as 22mm Water Trap Tee

U:Doheny_LT/SectorCompetitivePartsInitiative.ppt 28mm – 22mm –15mm Reducers Provide a simple solution to interchange between: 28mm piping and fittings to 22mm piping and fittings or 22mm piping and fittings to 15mm piping and fittings

U:Doheny_LT/SectorCompetitivePartsInitiative.ppt 15mm and 22mm Stem Elbows Enables tight 90-degree turns from the outlet of any 15mm or 22mm fitting

Brass Stem Adaptors Provide a male threaded connection converting to push-fit fitting

How do the fittings work? Simple push-to-connect system Collet gripper has stainless steel teeth that bite into tubing “O” ring provides permanent leak-proof seal

Tubing EZAir line promotes use of non-anodized tubing Anodized tubing is too hard for stainless collet to bite into tubing Non anodized tubing makes installation simple and requires very little instruction

Non-Anodized Tubing Achieves better air quality delivery than black steel or galvanized tubing Equal quality to that of copper tubing Non-anodized tubing could oxidize if moisture is allowed to lay in the piping Will build up white powder to self protect against corrosion

EZAir Tubing 10 foot tubing lengths sold in pack quantities of 10 Shorter lengths - less handling in warehouse Lower cost and easier transportation Less storage space needed, easier for distributors to stock Tubing can still be formed with pipe bender

Assembly of Pipe & Fittings It is essential that all installers and users of the EZAir system have a copy of our installation instructions. It is vital that the procedures stated in the instructions are followed for a safe and secure working system.

Tube Preparation Tubing must be cut square. Use a suitable pipe cutter to ensure that the ends of the tubing are free from any burrs that might damage the “O” ring

Assembly of 15mm and 22mm fittings Make sure the tube ends are cut square Verify the piping and fittings are clean Simply push the pipe until it reaches a stopping point in the fitting Pull on the pipe to check that fitting is secure. Assembly Check

Disconnecting 15mm and 22mm Tube & Fittings Push in collet and pull on tubing

Assembly of 28mm Fittings Prepare tubing Loosen screw cap 1/4 turn Insert tubing until it reaches internal stop Push tubing until it reaches internal stop and turn screw cap until tight on tubing 28mm assembly

Disconnecting 28mm Tubing Turn screw cap counter-clockwise 1/4 turn Push in collet & pull on pipe at the same time Disconnection

Piping Capacities 15mm 103psig (7 bar) 15mm 118psig (8 bar) 15mm 147psig (10 bar) 22mm 103psig (7 bar) 22mm 118psig (8 bar) 22mm 147psig (10 bar) 28mm 103psig (7bar) 28mm (8bar) 28mm 147psig (10bar) 1 psi loss per 30 meters (100ft) for a straight line.5 psi loss per 30 meters (100ft) for a loop system

EZAir Testing Tested to ANSI B x burst psig test 1.5 times leak - 225psi test No leakage at any pressure - up to failure 150psig (10BAR) Maximum working pressure allowed to comply with ANSI B31.1 testing standard

EZAir Endurance Testing EZAir line tested in temperature chamber between : -20°C (-4°F) to +60°C (+140°F) Cycle tested every 5 seconds (0-175psig) Temperature range cycled every 2 hours Over 1,000,000 cycles completed so far

Competition Steel pipe – needs skill, tooling, heavy and time consuming to install Copper – needs skill, costly and time consuming to install Plastic pipe & hose – not durable and very dangerous

Marketing Support 4 Page Sales Brochure Installation Instructions

A Light Industrial Revolution You now have the solution!