Air tank installation instructions Included parts: Raw aluminum air tank bracket 5/16-18 button head bolts (qty 4) M8x1.25 button head bolts (qty 4) M8.

Slides:



Advertisements
Similar presentations
Sectional Assembly and Installation
Advertisements

J.P. Langston Brake Retrofit
Mechanical Division Standard Hand Tools. Topics Design T-Square Drafting Triangle Fabrication Hacksaw Cordless Drill File Sandpaper & Steel Wool Assembly.
Stable Rise – Fixed Bracket / Stationary Top Installation and Set Up Guide Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH
Tools MVRT Season. Overview Design –Combination Square –Caliper Fabrication –Hacksaw –File –Drill –Sandpaper/Steel Wool –Shears Assembly –Allen.
Frame Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team
Installation instructions for the one and only 3 point strut bar for the 5 th gen Accord Please follow the instructions to ensure proper fitment of the.
Peppermill Demo Bayou Woodturners Demonstrator Jim Shackelford November 2009.
Metering Pump Spare Parts Replacement. Pump Components (Metering Pump) Pumps are supplied with a 120VAC or 240VAC power cord. Use care to ensure pump.
Instructions for Diaphragm Replacement Cat. Nos. 2052B-01, 2054B-01
Honda 450 Installation Manual.
A-dec 300 Dual Mount on 500 Installation. Agenda ► General Information ► Recommended tools ► Installation ► Follow through install guide ► Hands-on install.
Installation. Indoor Unit Installation Typical Installation.
ZIPP 404 BEARING REPLACMENT GUIDE Tools Needed:
RL brake caliper Installation instructions Included parts: Solid billet aluminum caliper brackets (qty 2) 9/16 grade 8 bolts (qty 2) 9/16 grade 8 washers.
Click on this image to open the full PDF document.
Series I Pump and Prep Pump Prior to removing the head, rotate the flag on the top of the motor so the piston is fully retracted. Remove thumb nuts.
Flange-lok Installation Instructions Quick Installation Guide rev. DB.
Rev. A Control Number XXXXXXXXXXX Effective Date 10/2/2008 Field Work Instructions for Placard replacement Functional Trainer Page 1/4 Revised Date 10/2/2008.
1 STEPMILL 7000 PT ASSEMBLY INSTRUCTIONS PART NUMBER
Honda Recon TRX-250 Installation Manual. STEP 1: Remove rear tires and install axle spacers. Use blue thread locker and tighten lugs to ATV specification:
MyLock 644D Service Seminar.
Robot Quick Build Session Frame Assembly Instructions Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team 1750 Special Thanks to Oklahoma.
Step 12 Here is the issue…..the mount for the throttle arm is pushed up against the side of the housing. The problem with this is it allows (due to alignment)
Stable Rise –Pull and Swivel Top Installation and Set Up Guide Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH
ASSEMBLY INSTRUCTIONS. 2 ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: SIDE CUTTING PLIERS PRY BAR 7/16” & 9/16” WRENCH 3/16” ALLEN WRENCH T-15 TORQUE.
860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in  Lead free version (LF860) was introduced in Parts do not.
994 RPDA 21/2”- 6”. Modification Overview  Production of the 994RPDA began in 1999 and is current.  The 994 RPDA currently utilizes the ¾” 009M3 for.
Service Seminar Memory Craft Table of Contents MC10001 Top Cover Removal…………………………………………………………………..…………1 Belt Cover Removal……………………………………………………………..……………2-4.
Extended top hats installation instructions Included parts: Extended top hats (qty 2) Spring isolator bushing (qty 2) Energy Suspension top hat bushings.
Drilling machine.
USING THE LATHE TO MAKE THE TENSILE TESTING SAMPLE
Hand Tools Power Tools Shop Equipment Measurement.
After Receiving this error code, Follow these steps to correct the problem… Click for next slide.
MR. PATTERSON CONSTRUCTION TECH 1
MC11000 Kit Replacement 1 1. Open the face plate and remove the 2 screws. Remove and discard the original face plate. 3. Remove the 2 white caps on the.
General Instructions for “KidWind Light” wind tunnel.
Module-6 Drilling.
Getting Ready Gather tools, oil and filter. If you plan to change your oil regularly, consider investing in jack stands, a socket set and an oil drain.
© 2011 Pearson Education, Inc. All Rights Reserved Automotive Technology, Fifth Edition James Halderman FASTENERS AND THREAD REPAIR 8.
994 2½ ”- 10”. Modification Overview  Production for the 994 began in 1999 and is current.
Shop Built Magnetic LED Light Bob Clark Aug, 11, 2011.
LAB #9 Valve Head replacement. Insert the valve. Make sure that the cap goes on the intake valve. Insert the springs. Insert the keeper.
LAB #10. Governor Control Arm Using a 10mm socket install the two bolts that hold the governor control arm. Finger tighten then torque to 100 “#
Model 12 Intek Horizontal OHV
TURBO REBUILD TURBO REBUILD. Step 1 Step 1: - Using the small pick or screwdriver, walk the tiny snap ring back into the groove on both the compressor.
How to Change Raptor Knife Blades. Step 1: Use a Phillips screwdriver to remove the 5 screws. It is not necessary to remove the lanyard/webbing to change.
XR621 Drive Hose Update Kit. Removal Turn off Battery dis Drain hydraulic tank Remove both rubber lines under chassis and discard. Remove and discard.
Easy Reach 7.0 Honda Element Packing List QtyDescriptionPacked 115ft 10ga Red Wire 16ft 10ga Black Wire 140amp Breaker 23/8 Yellow Ring Terminals 25/16.
450 4”-10”. Modification Overview  Production of the 4” - 10” sizes began in  The lead free version (XL) was introduced in 2011.
Rapid Change Technology The following is a presentation to aid Technicians in the replacement of the Rapid Change Technology Block.
AVIVA™ ELECTRIC BIKES VIPER ASSEMBLY INSTRUCTIONS Aviva™ - For A New Way Of Life.
Genuine N1. Conversion Installation manual LC 120 5D 2003
Assembly of steering.
Annex 4 - Moving Frame and Whiffletree assembly
Instructions for Diaphragm Replacement Cat. Nos. 2052B-01, 2054B-01
Assembly Instructions:
FASTENERS AND THREAD REPAIR
IN-VEHICLE ENGINE SERVICE
826YD 21/2”-10”.
Easy Reach 7.0 Honda Element 2003
Easy Reach 7.0 Honda Element 2003
2000SS 2½”-12”.
Genuine N1. Conversion Installation manual LC
Assembly instructions for M-K all bolt together hoppercone kit.
Mounting a BalanceBox®650 to a brick wall
774 DCDA 21/2”-12”.
2000SS 2½”-12”.
880V 21/2”-10”.
774 2½”-12”.
Presentation transcript:

Air tank installation instructions Included parts: Raw aluminum air tank bracket 5/16-18 button head bolts (qty 4) M8x1.25 button head bolts (qty 4) M8 washers (qty 4) M8x1.25 flange nuts (qty 4) Tools needed for installation: Rachet 12mm socket 13mm socket 5mm allen wrench 3/8 allen wrench Center punch Stepped drill bit Cordless drill Interior panel puller

Step 1 – Lower the back seat to expose the 5 interior panel clips that will need to be removed. Use your panel puller took to remove them.

Step 2 – Next, lift the edge of the plastic panel to expose the 12mm factory bolt that needs to be removed. There are 2 that need to be removed.

Step 3 – After you have removed the factory bolt, replace it with the supplied M8x1.25 button head bolt and washer.

Step 4 – Now get your bracket and flip it over so the recessed holes are facing towards you. Take the supplied 5/16 bolts and your EXO mounts and bolt these together.

Step 5 – Here you can see the two new bolts that were installed in Step 3, take you FFC bracket with the EXO mounts installed and slide it over the exposed thread of the bolts. Install the supplied M8 flange nuts and tighten by hand.

Step 6 – Now take your center punch and mark where to drill. After you have center punched the hole, go ahead and remove the FFC bracket.

Step 7 – Get your stepped drill bit and cordless drill, find your center punch mark and begin drilling. *Be sure you hold the plastic panel on the other side to prevent from drilling into it. Depending on how perfect your center punch hole is you may need to enlarge the hole slightly. Start with a 3/8 inch hole, if that doesn’t work, then widen the hole by a 1/32 nd of an inch at a time. *Note: Go no larger than a 7/16 th hole.

Step 8 – Re-install the FFC bracket and use the supplied M8 bolts and large washers, thread them into the bracket. Be sure to hole the FFC bracket tight to car as you tighten the bolts.

Step 9 – Now installed the supplied nuts onto the bolts that you just installed and tightened. Be sure the bolts are tight before installing the nuts.

Step 10 – After you tighten the lower nuts, go ahead and tighten the upper nuts that were installed just hand tight.

Step 12 – Be sure that when you install your air tank that you used the cut out for your pressure switch. Rotate the air tank until you have it the correct way.

Step 12 – Install your air tank, Congratulations you are finished installing your new FFC air tank bracket.