GNI0003H PP1 Loop Trainer. GNI0003H PP2 Reason for Study Because the Loop Trainer gives instructors the capability to control water flow, pressure and.

Slides:



Advertisements
Similar presentations
Generic Pressurized Water Reactor (PWR): Safety Systems Overview
Advertisements

Circulating Water System
START-UP AND OPERATION OF MECHANICALLY SEALED EQUIPMENT 1:13.
Setup/Installation/Operation of an Environmental Control Unit (ECU)
Perform Control Test. Check for Consistent Liquid Temperatures Entering and Leaving Liquid Temperatures should be close when the water pumps are on but.
STEAM TRAPS.
UL/FM Fire Pump Systems Lunch & Learn 04/18/05
Filter manifold Holding tank Iron- manganese filter Aeration tank Control unit Pre- filter To storage tanks Backwash overflow SO2 vent Bypass Cutoff valve.
1B-1 Fire Engine Maintenance Unit 1B – Pump Inspections and Maintenance.
"AIR COOLER" Heat Exchanger
ACADs (08-006) Covered Keywords Components, functions, operation, Auxiliary feedwater, Startup, hot standby, plant cooldown, emergency. Description Supporting.
AC Power TCZ Pump VVVF Drive TT 2 W/H CWS 4-way valves TT 3 TT 4 TT 1 S2 S1 FT 1 CWR FT 2 CW CWS = Cold Water Supply CWR = Cold Water Return CW = Cold.
Skilled Trades 1201 Residential Plumbing.
Pump Installation Vigyan Ashram, Pabal.
Chapter 12: Alternative Technologies To be used with the Guide to Building Energy Efficient Homes in Kentucky.
Fuel Oil Systems Fuel Oil Systems consist of: Storage Tanks Pumps
STEAM HEATING.
Hydronic Mechanical Controls
Hydraulics For The Long Term
ELECTRONIC FUEL INJECTION COMPONENTS
2 Instructor Training MPTT Flow Loop System VLP-TRN-MPTT.
ACADs (08-006) Covered Keywords Description Supporting Material
Lease Automatic Custody Transfer
1 Fuel Pumps. 2 Pumps 1.All oil burners for residential heating have pumps A. They are connected to a motor through a coupling 2.Description A. An oil.
Water Handling Operations
Plan 2 – Dead-end Seal Chamber Optional Jacket
Industrial Process Control: CONTROL OF HEAT EXCHANGER
APPROVED TRAINING MANUAL’S LESSON PLANS AND COURSEWARE STAR MARIANAS AIR, INC. Recurrent – Flight Crew Part III – Aircraft Ground Training Section 2 –
BOILER PLANT OPERATION Presented By Mr. Sivanand Ray
JC Equipments Pvt. Ltd Heat Exchanger Manufacturers
                    P&ID: Tutorial 1
“Fix Tube Sheet” Heat Exchanger
HOW THE DUMP RESISTOR’S TANK LOOKS LIKE COOLING OF THE LHC ENERGY EXTRACTION RESISTORS G. Peón (ST/CV), K. Dahlerup-Petersen, G. Coelingh (AT/MEL) Air.
Model 2537A Training Course Detailed Instrument Description Rev: Nov
LSU Petroleum Engineering Research and Technology Transfer Laboratory “The Well Facility”
Weekly Checks Monday – VSP Room Tuesday – Pilothouse System Controls Wednesday – Starboard / Engine Room Thursday – Foam Room Friday – Port / Engine Room.
Monday – VSP Room weekly checks Visually Check: Hvac system for leaks & valve settings Fresh water system for leaks & valve settings VSP linkage Autopilot.
Potable Water System General Locations and Operations.
Machinery Cooling Water System Locations and Operations.
1 OF 16 INFO:You observe that this fire pump system is leaking. This fire pump system is not designed to leak. DEF:Leaking Central Water Supply (Domestic.
OILGEAR PVV PUMPS PVV 200 Performance Curves.
Pulp Mill Operator Training Class 3
Ice Energy Extraction Unit. Throttling Valve Ice Tank PVC piping Radiator Drain Valve Plexiglas Fan mounted against back of radiator Overall View Plywood.
SYSTEMS. Pumps Systems Our systems are identified as follows Example: model D-CPS-HT-1000-VFD Dis for Duplex units CPSis for Constant Pressure System.
TYPE “HOS” 6” Stroke Compressor & Ancillary Equipment
ARÇELİK TİCARİ KLİMA EĞİTİM DÖKÜMANI APPENDIX.
Vertical Pump Motor Manifold Upgrade. VPMM Replaces Existing Pumps, Motors, Relief Valves, Check Valves, Discharge Filters, Pump Running Pressure Gauges,
James McIntyre VRF Training Manager V5 Key Components.
Industrial Resources, Inc.
DEAERATOR-STAGE-II/TPS-II /NLC INDIA LTD
ACTIVE SOLAR DESIGN ALTERNATIVE ENEGRY SOURCES.
Design, Evaluation and Application of a Fuel Cell Vehicle
Brooks Expert Support Tool (BEST) Software
Design of the thermosiphon Test Facilities 2nd Thermosiphon Workshop
ARAC/H/F Air-cooled water chillers, free-cooling chillers and heat pumps Range: kW.
COMPONENTS OF SOLAR WATER HEATER
Module 3 Domestic Heating/MMA Welding
Student CD for Commercial Refrigeration for A/C Technicians Chapter 12 Ice Machines.
SB Packing Automatic Downpuller Power Unit
R3 Controls, Valves, Accessories & Heat Pumps
Reheat Coil (Typical of 5)
AIR COMPRESOR Chapter-13.
Air Treatment School Refrigerated Dryer Training
WATER AND STEAM SYSTEM.
SNS PPU Cryomodule Instrumentation
Presentation transcript:

GNI0003H PP1 Loop Trainer

GNI0003H PP2 Reason for Study Because the Loop Trainer gives instructors the capability to control water flow, pressure and temperature, it can be used to simulate almost any scenario in real time.

GNI0003H PP3 Reason for Study The Loop Trainer can also be used to simulate special conditions, such as radiation control areas and to train employees on clearance and tagging procedures as well as maintenance and operation tasks.

GNI0003H PP4 Objectives Given the Loop Trainer System Description EXPLAIN the system function of: –Cooling Water Loop –Heat Transfer Loop –Recirculation Loop –Loop Cross-connections

GNI0003H PP5 Objectives Given the Loop Trainer System Description EXPLAIN the following components: –Electrical Power Sources –Cooling Water Pumps –Heat Transfer Pump –Recirculation Pump

GNI0003H PP6 Objectives Given the Loop Trainer System Description EXPLAIN the following components: –Motor Operated Valves –Air Operated Valves –Solenoid Valves –Controls

GNI0003H PP7 Objectives Given TAP-414, “TTF Flow Loop Trainer Operation,” PERFORM a walk-through of how to place the loop trainer in service (Laboratory).

GNI0003H PP8 Objectives Given “TTF Flow Loop Trainer Qualification Checkout Card QCC INQ0007H,” REVIEW the elements required to obtain the qualification.

GNI0003H PP9

10 Cooling Water Storage Tank Valve locations

GNI0003H PP11 Cooling Water Storage Tank Valves Drain Valve Isolation Valve Instrument Isolation Valve

GNI0003H PP12 Cooling Water Pump B Cooling Water Pump A

GNI0003H PP13 1CW-016, Cooling Water Pumps Suction Strainer

GNI0003H PP14 1CW-015, Cooling Water Pumps Pressure Switch Isolation Valve PS-9010, Pressure Switch

GNI0003H PP15 1CW-018, Cooling Water Pump 1B Suction Isolation Valve 1CW-017, Cooling Water Pump 1A Suction Isolation Valve

GNI0003H PP16 1CW-004, Cooling Water Pump 1B Discharge Isolation Valve 1CW-002, Cooling Water Pump 1A Discharge Isolation Valve

GNI0003H PP17 1CW-009, Cooling Water Pump Recirculation Valve

GNI0003H PP18 Emergency Stop Buttons for Cooling Water Pumps

GNI0003H PP19

GNI0003H PP20 Mechanical Lab 120 Components

GNI0003H PP21 Continuation of Cooling Water Loop with Piping and MOV’s

GNI0003H PP22 MOV’s for Cooling Water Loop

GNI0003H PP23 1CW-023, LP Heater #1 Inlet Tube Side Drain Valve 1CW-005, LP Heater #1 Inlet Tube Side Isolation Valve

GNI0003H PP24 1CW-021, Cooling Water Outlet Header Drain Valve 1CW-006, LP Heater #1 Outlet Tube Side Isolation Valve

GNI0003H PP25 1CW-024, LP Heater #2 Inlet Tube Side Drain Valve 1CW-007, LP Heater #2 Inlet Tube Side Isolation Valve

GNI0003H PP26 1CW-022, Cooling Water Outlet Header Drain Valve 1CW-008, LP Heater #2 Outlet Tube Side Isolation Valve

GNI0003H PP27 1CW-019, TCV for LP Heater #1 1CW-020, TCV for LP Heater #2

GNI0003H PP28 LCV 2001 & 2002 M/A Stations on Loop Trainer Control Panel for 1CW-019 & 1CW-020 Temperature Control Valves

GNI0003H PP29 1CW-9 Switch to OPEN

GNI0003H PP30 MCC

GNI0003H PP31 MCC Main Breaker

GNI0003H PP32

GNI0003H PP33

GNI0003H PP34 Loop Trainer Control Panel

GNI0003H PP35

GNI0003H PP36

GNI0003H PP37

GNI0003H PP38

GNI0003H PP39 1CW-9 Switch to MODULATE

GNI0003H PP40 LCV 2001 & 2002 Stations

GNI0003H PP41 Emergency Stop Buttons for Cooling Water Pumps

GNI0003H PP42 Cooling Water Pumps can be stopped from Loop Trainer Control Panel

GNI0003H PP43 General View of Heat Transfer Loop

GNI0003H PP44 Hot Water Storage Tank Loop Trainer Control Panel MOV’s for Cooling Water Loop LP #1 & #2 Heaters

GNI0003H PP45 LP Heater #1 LP Heater #2 Hot Water Storage Tank

GNI0003H PP46 LP Heater #1 LP Heater #2

GNI0003H PP47 View from Rear of Lab 120 Flow Loop MOV’s for Cooling Water Loop LP #1 & #2 Heaters

GNI0003H PP48 View from Rear of Lab 120 Flow Loop LP #1 & #2 Heaters Hot Water Storage Tank

GNI0003H PP49 Fill Connection for Heat Transfer Loop (near Relief Valve 1HT-017)

GNI0003H PP50 Heat Transfer Loop High Point Vent Valve 1HT-019

GNI0003H PP51 1HT-004 Bonnet (may require loosening to allow air to escape when filling venting Heat Transfer Loop)

GNI0003H PP52 1HT-005 Heat Transfer Pump Suction Drain Valve SHUT

GNI0003H PP53 1HT-001, LP#1 Heater Shell Inlet Isolation Valve OPEN

GNI0003H PP54 1HT-002, LP#2 Heater Shell Inlet Isolation Valve OPEN

GNI0003H PP55 1HT-003, LP#1 Heater Shell Outlet Isolation Valve OPEN

GNI0003H PP56 1HT-001, LP#2 Heater Shell Outlet Isolation Valve OPEN

GNI0003H PP57 Heat Transfer Pump Suction Strainer Clean

GNI0003H PP58 1HT-006, Heat Transfer Pump Suction Isolation Valve OPEN

GNI0003H PP59 1HT-007, Heat Transfer Pump Suction PI Isolation Valve OPEN

GNI0003H PP60 1HT-013, Heat Transfer Pump Discharge Isolation Valve OPEN

GNI0003H PP61 FT-2000 Valved in & Vented

GNI0003H PP62 FT-2000 Valved in & Vented

GNI0003H PP63 1HT-016, Heat Transfer Flow Control Valve

GNI0003H PP64 1HT-016, Heat Transfer Loop Pressure Relief Valve

GNI0003H PP65

GNI0003H PP66

GNI0003H PP67 TC-2000 & FC-2000

GNI0003H PP68 Tune FC-2000 (or TC-2000) to adjust flow through 1HT-016 as required

GNI0003H PP69

GNI0003H PP70 Heat Transfer Pump Emergency Stop Button

GNI0003H PP71 Heat transfer Pump can be stopped from Loop Trainer Control Panel

GNI0003H PP72 Recirculation Loop

GNI0003H PP73 Fill Location for Hot Water Storage Tank (at manway)

GNI0003H PP74 Water must cover heater elements in Hot Water Storage Tank (ensure above tube bundle)

GNI0003H PP75 1HW-004, Hot Water Pump Suction Line Drain Valve SHUT

GNI0003H PP76 1HW-021, Hot Water Pump Suction Strainer is CLEAN

GNI0003H PP77 1HW-003, Pressure Switch PS-1100 Isolation Valve OPEN

GNI0003H PP78 1HW-007, Hot Water Pump Discharge IsolationValve is OPEN

GNI0003H PP79 1HW-015, Hot Water Discharge Line DrainValve is SHUT

GNI0003H PP80 1HW-016, Hot Water Tank Isolation Valve is OPEN

GNI0003H PP81

GNI0003H PP82

GNI0003H PP83

GNI0003H PP84 DP Gauge for Hot Water Pump In Recirculation Loop – Throttle 1HW-007 Discharge Valve to maintain 12.5 to 14.5 psi

GNI0003H PP85

GNI0003H PP86

GNI0003H PP87

GNI0003H PP88 Heater Elements in Hot Water Storage Tank

GNI0003H PP89 TI-2200 (Temperature Indication <140 degrees F

GNI0003H PP90 Emergency Stop Button for Recirculation Pump (Hot Water Pump)

GNI0003H PP91

GNI0003H PP92

GNI0003H PP93 Electrical Components

GNI0003H PP94 Power Panel PPAA located in chase between Labs 107 and 108

GNI0003H PP95 Large Breaker at bottom of PPAA Panel (480 VAC 3 phase that powers 6.9 KV breaker simulator)

GNI0003H PP96

GNI0003H PP97

GNI0003H PP98

GNI0003H PP99

GNI0003H PP100

GNI0003H PP101

GNI0003H PP102

GNI0003H PP103

GNI0003H PP104

GNI0003H PP105

GNI0003H PP106

GNI0003H PP107

GNI0003H PP108

GNI0003H PP109

GNI0003H PP110

GNI0003H PP111

GNI0003H PP112

GNI0003H PP113

GNI0003H PP114

GNI0003H PP115

GNI0003H PP116

GNI0003H PP117

GNI0003H PP118

GNI0003H PP119

GNI0003H PP120

GNI0003H PP121 MCC & ARP-1

GNI0003H PP122 Time for Questions and Objectives Review