RLC circuits - Part 2 Resonance/Notches/Bandpass Cartoon from Agilent,

Inductors - how do they work? L Start with no current in the circuit. When the battery is connected, the inductor is resistant to the flow of current. Gradually the current increases to the fixed value V 0 /R, meaning that the voltage across the inductor goes to zero. In reality the inductor has a finite resistance since it is a long wire so it will then be more like a pair of series resistances. R V0V0

Inductors - time constant L/R Again the behavior of an inductor is seen by analysis with Kirchoff’s laws. Suppose we start with no current. VRVR V0V0 VLVL There is a fundamental time scale set by L/R, which has units of seconds (=Henry/Ohm) thenand

RLC circuits with sinusoidal sources The AC analysis of circuits with inductors is also easy, with the effective resistance (impedance) of an inductor equal to i  L. From a phasor point of view this means that the inductor leads the resistor by 90 degrees. High pass and low pass filters can be made from inductors as well. However the inductors are usually bulkier and relatively expensive compared to capacitors (and more difficult to make in an integrated circuit) so are not used as commonly. Another limitation is that they are far from ideal. The impedance is usually R L +i  L, which means that in order to find the breakpoint you use f = L/(2  (R L +R)).

Notch and Bandpass A filter can also serve to select or eliminate a narrow band of frequencies. Examples are radio (select) and parental control “channel eliminator” circuits. V out Log 10 f V out Log 10 f

Mathematical analysis of a series LRC circuit - bandpass filter R V in C L V out First find the total impedance of the circuit Using a voltage divider The phase shift goes from 90°to -90°.

Mathematical analysis of a series LRC circuit - bandpass filter (2) R V in C L V out The magnitude of the gain, A v, is Note that for high frequencies  L is dominant and the gain is R/  L or small. At low frequencies the gain is  RC because the impedance of the capacitor is dominant. At  2 = 1/LC the gain is one (assuming ideal components).

Graphing for a series LRC circuit RLC bandpass filter Log10 Freq Gain Although the gain falls off at 20 dB/decade at high and low frequencies (this means that it is proportional to  ) it is more typical to plot it as shown on a semi-log graph, since this emphasizes the peak.

Q factor for a Series LRC circuit RLC bandpass filter Log10 Freq Gain The quality factor or Q is defined as the energy stored divided by the energy loss/cycle. For an electronic bandpass it is the peak frequency divided by the width of the peak or bandwidth (defined by the frequencies where the gain is 3 dB lower than the maximum). Solve

Parallel LRC circuit Measured across the resistor, this circuit is a notch filter, that is it attenuates a small band of frequencies. The bandwidth in this case is defined by 3dB from the lowest point on the graph. R V in C V out

Transients in a series LRC circuit - Ringing Suppose instead of a sinusoidal source we had a slowly varying square waveform or a sharp turn on of voltage. How would a LRC circuit behave? We can start by using Kirchoff’s laws again. R V in C L V out This is a second order differential equation that can be solve for the general and particular solutions.

Transients in a series LRC circuit - Ringing (2) The solutions to the quadratic above determine the form of the solutions. We will just state the solutions for different value of R, L and C. R V in C L V out

Transients in a series LRC circuit - Ringing (3) The last, underdamped, results in an exponentially decaying envelope and a sinusoidal oscillations. This ringing is commonly observed. It can be thought of as two parts: a loss of energy related to R and an oscillation related to the product LC. This not exact so lets look at the mathematical solution. R V in C L V out When (RC )2 >>LC the cos will oscillate several times at a frequency almost equal to the resonant frequency.