WETSIDE DESIGN © Copyright 2008 HVAC Design Solutions1 Essential Design Programs with Accurate Sizing Calculations help to “Streamline Your Design” Essential Design Programs with Accurate Sizing Calculations help to “Streamline Your Design” H VAC D ESIGN S OLUTIONS ENGINEERING SOFTWARE ENGINEERING SOFTWARE

 “Wetside Design” from HVAC Design Solutions is a package of software programs for many of the HVAC Designer’s sizing tasks:  Hydronic System Sizing -“Optimum Sizes”  Pump Head Calcs (Primary, Secondary, & Condenser Water Pumps)  Heating Water Expansion Tank Sizing  Chilled Water Expansion Tank Sizing  Coil Psychrometrics & Coil GPM Calcs  Extensive Help Files, and “Extras” © Copyright 2008 HVAC Design Solutions2

 Reduce your dependence on Reference Books, Charts, Graphs, and “Rules of Thumb”.  Eliminate many of the usual HVAC Design Tasks  Reduce common errors and mistakes  Create an easy-to-follow, step-by-step “Procedure for Wetside Design” for all projects. © Copyright 2008 HVAC Design Solutions3 Software Package contains most of the sizing calculations and procedures for typical projects

© Copyright 2008 HVAC Design Solutions4 “Any One of these programs is worth the cost of the Entire Package!” Quick Links to all calculation programs

© Copyright 2008 HVAC Design Solutions5 Begin with Basic Project Information input Information automatically transfers to all programs Design Conditions are used in many calculations

© Copyright 2008 HVAC Design Solutions6 Warning Flags for Alternate Sizes Alternate Pipe Sizes Quick and Easy Input Most “Economical” Pipe Sizes to meet Sizing Criteria (Velocity and Pressure Drop)

© Copyright 2008 HVAC Design Solutions7 Preliminary Pump Head Calcs, for preliminary Pump HP requirements Quick and Easy Input “Approximate” Fitting and Valve counts

© Copyright 2008 HVAC Design Solutions8 Typical Project Example for Primary Pump Head Calcs

© Copyright 2008 HVAC Design Solutions9 Easy Input of System Components and GPM Quantities Running Total of Approx. Pump BHP

© Copyright 2008 HVAC Design Solutions10 Easy Input of System Components and GPM Quantities Built-in Fitting Coefficients

© Copyright 2008 HVAC Design Solutions11 Allowance for Items at Chiller or Boiler Generic Values Built-in (Conservative) if Mfgr’s. Data Unknown

© Copyright 2008 HVAC Design Solutions12 Adjustments for Glycol (if applicable) and/or Safety Factor Imput Length of “Longest Run” Piping (Measured “Out & Back” to Pump) Final, Totalized Primary Pump Head (Ft.) for the System

© Copyright 2008 HVAC Design Solutions13 After Input is complete, press “Compile & Print” Button for full System Report

© Copyright 2008 HVAC Design Solutions14 Psychrometric Calculations Assist with Preliminary Equipment Selection, Preliminary Pump Sizing, Etc.

© Copyright 2008 HVAC Design Solutions15 Heating Water and Chilled Water Expansion Tank Sizing Programs Built-in Water Volumes, Expansion Factors, Acceptance Factors, and Expansion Formulas

© Copyright 2008 HVAC Design Solutions16 “Programming” Information Request Forms for Owner or Architect Input

© Copyright 2008 HVAC Design Solutions17 Extensive “Quality Control” Mechanical Checklists are available in a separate “Mechanical Peer Review” Software Package Over (110) Pages of Checklists and Spreadsheets for a thorough review of Mechanical Construction Documents

© Copyright 2008 HVAC Design Solutions18 Example of Quality Control Check List Items

© Copyright 2008 HVAC Design Solutions19 After completing input and calculations, Output and Sizing Documents can be printed for submittal to building department officials and for addition to drawings and schedules

© Copyright 2008 HVAC Design Solutions20 Extensive Wetside Programs to help “Streamline” your Design Procedures

 Straightforward takeoff and input allows easy calculation and sizing of Wetside Systems.  Extensive procedures, formulas, charts, and tables as prescribed by Mechanical Codes and as recommended by ASHRAE and Equipment Manufacturers have been included and have been used to establish the “Accurate” Wetside System Sizes.  Multiple Programs are included, covering most of the typical Wetside Design Tasks for most projects. © Copyright 2008 HVAC Design Solutions21

 Significantly reduces “Reference Material Dependence” which can save a great deal of time and effort.  Output in the form of Compliance Documents or System Sizing Summaries for submittal to appropriate code enforcement officials or building departments.  Extensive “Help Files” that are hyperlinked to each program, form, or table. © Copyright 2008 HVAC Design Solutions22

 Limited time “Special Pricing” available at our website  Wetside Design Package Original Price: $225 US, Special Price: $169 US  Mechanical Peer Review Package Original Price: $275 US, Special Price: $198 US © Copyright 2008 HVAC Design Solutions23

 Current Version: 2.12, with latest update (08/24/2008) Free updates, as available.  To purchase Wetside Design or Mechanical Peer Review, visit our website at and go to the Prices/Orders page  Software can be downloaded for immediate installation (with password) after purchase is confirmed © Copyright 2008 HVAC Design Solutions24

 OS: Windows® 98, 2000, XP, 2003, Vista  Processor: Pentium® or equivalent  Ram: 512MB (minimum recommended)  Disk Space: 100 MB (recommended)  Software: MS Word®, MS Excel® © Copyright 2008 HVAC Design Solutions25

 Thank you for taking your time to review our Wetside Design software packages  If you have any questions or comments, you can to: steve”at”hvacdesignsolutions.com, or support”at”hvacdesignsolutions.com  We also have an interactive demo of our Wetside Design software that can be delivered, on request, via . © Copyright 2008 HVAC Design Solutions26